time in the cases where it really sends the drive out to lunch, but it also
allows us to catch very wierd edge cases of strange drives that might take
a very long time (emulated disk drives over a network, e.g.).
quirk regarding the C- series makes me suspect that all Olympus models have
the same quirks, but I cannot prove it.
Submitted by: Bernd Walter <ticso@cicely8.cicely.de>
attempts to set buffered mode was printing out "unable to set buffered
mode" no matter what. Oops.
Spotted by: Joerg Wunsch <joerg_wunsch@uriah.heep.sax.de>
MFC after: 3 weeks
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
Clear residual counts after a successful samount (the user doesn't
care that we got an N-kbyte residual on our test read).
Change a lot of error handling code.
1. If we end up in saerror, check more carefully about the kind of
error. If it is a CAM_SCSI_STATUS_ERROR and it is a read/write
command, we'll be handling this in saerror. If it isn't a read/write
command, check to see whether this is just an EOM/EOP check condition-
if it is, just set residual and return normally. A residual and
then a NO SENSE check condiftion with the ASC of 0 and ASCQ of
between 1 and 4 are normal 'signifying' events, not errors per se,
and we shouldn't give the command to cam_periph_error to do something
relatively unpredictable with.
2. If we get a Bus Reset, had a BDR sent, or get the cam status of
CAM_REQUEUE_REQ, check the retry count on the command. The default
error handler, cam_periph_error, doesn't honor retry count in these
cases. This may change in the future, but for now, make sure we
set EIO and return without calling cam_periph_error if the retry
count for the command with an error is zero.
3. Clean up the pending error case goop and handle cases more
sensibly.
The rules are:
If command was a Write:
If we got a SSD_KEY_VOLUME_OVERFLOW, the resid is
propagated and we set ENOSPC as the error.
Else if we got an EOM condition- just mark EOM pending.
And set a residual of zero. For the longest time I was just
propagating residual from the sense data- but my tape
comparison tests were always failing because all drives I
tested with actually *do* write the data anyway- the EOM
(early warning) condition occurred *prior* to all of the
data going out to media- that is, it was still buffered by
the drive. This case is described in SCSI-2, 10.2.14,
paragraph #d for the meaning of 'information field'. A
better fix for this would be to issue a WFM command of zero
to cause the drive to flush any buffered data, but this
would require a fairly extensive rewrite.
Else if the command was a READ:
If we got a SSD_KEY_BLANK_CHECK-
If we have a One Filemark EOT model- mark EOM as pending,
otherwise set EIO as the erorr.
Else if we found a Filemark-
If we're in Fixed Block mode- mark EOF pending.
If we had an ILI (Incorrect Length Indicator)-
If the residual is less than zero, whine about tape record
being too big for user's buffer, otherwise if we were in
Fixed Block mode, mark EIO as pending.
All 'pending' conditions mean that the command in question completes
without error indication. It had succeeded, but a signifying event
occurred during its execution which will apply to the *next* command
that would be exexcuted. Except for the one EOM case above, we always
propagate residual.
Now, way back in sastart- if we notice any of the PENDING bits set,
we don't run the command we've just pulled off the wait queue. Instead,
we then figure out it's disposition based upon a previous command's
association with a signifying event.
If SA_FLAG_EOM_PENDING is set, we don't set an error. We just complete
the command with residual set to the request count (not data moved,
but no error). We continue on.
If SA_FLAG_EOF_PENDING- if we have this, it's only because we're in
Fixed Block mode- in which case we traverse all waiting buffers (which
we can get in fixed block mode because physio has split things up) and
mark them all as no error, but no data moved and complete them.
If SA_FLAG_EIO_PENDING, just mark the buffer with an EIO error
and complete it.
Then we clear all of the pending state bits- we're done.
MFC after: 4 weeks
Handle both old and new TARGIOALLOCUNIT/TARGIOFREEUNIT cases- the new
one allows us to specify inquiry data we want to use.
Handle more of the CAM_DIS_DISCONNECT case.
Move TARGCTLIOALLOCUNIT to OTARGCTLIOALLOCUNIT, TARGCTLIOFREEUNIT
to OTARGCTLIOFREEUNIT and redefine old associated structure to be
old_ioc_alloc_unit- deprecation but preservation of binaries.
Add new structure for same- but this one contains a pointer to
user defined INQUIRY data so you can define what the target
device looks like to the outside world.
1. If we get frozen, unfreeze for disable disconnects.
2. Put CAM_DIS_DISCONNECT commands at the head of the work queue
(we have a target still connected and we can't run anything else
until this command completes).
If we had an error sending the last CTIO, unfreeze the queue anyway.
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
This is useful if you want to dynamically move into a Fibre Channel
or Multi-initiator environment that happens to be particularly noisy
and ugly that requires a lot of retries (with shorter I/O timeouts)
for commands destried by LIPs or Bus Resets.
Reviewed by: deafening silence on audit && scsi on the retry counts
MFC after: 2 weeks
1. Add SA_IO_TIMEOUT as an option (4 minutes default) to cover reads,
writes, wfm, test unit ready.
2. Add internal SCSIOP_TIMEOUT (e.g., for mode sense) at 1 minute. This
should not require an option, but is cleaner to parameterize.
MFC after: 1 week
drivers.
- change daprevent() to set CAM_RETRY_SELTO and SF_RETRY_UA when it calls
cam_periph_runccb().
- change the pt(4) driver to ignore unit attentions
- change the targ(4) driver to retry selection timeouts
- clean up a few formatting glitches in the targ(4) driver
Reviewed by: gibbs
prevent scsi_sense_desc() from deferencing a NULL pointer when a drive
happens to return one of these sense keys.
Reported by: Michael Samuel <michael@miknet.net>
With the recent changes in the CAM error handling, some problems in
the error handling of sa(4) have been uncovered. Basically, a number
of conditions that are not actually errors have been mistreated as
genuine errors. In particular:
. Trying to read in variable length mode with a mismatched blocksize
between the on-tape (virtual) blocks and the read(2) supplied buffer
size, causing an ILI SCSI condition, have caused an attempt to retry
the supposedly `errored' transfer, causing the tape to be read
continuously until it eventually hit EOM. Since by default any
simple mt(1) operation does an initial test read, an `mt stat' was
sufficient to trigger this bug.
Note that it's Justin's opinion that treating a NO SENSE as an EIO
is another bug in CAM. I feel not authorized to fix cam_periph.c
without another confirmation that i'm on the right track, however.
. Hitting a filemark caused the read(2) syscall to return EIO, instead
of returning a `short read'. Note that the current fix only solves
this problem in variable length mode. Fixed length mode uses a
different code path, and since i didn't grok all the intentions behind
that handling, i did not touch it (IOW: it's still broken, and you get
an EIO upon hitting a filemark).
The solution is to keep track of those conditions inside saerror(),
and upon completion to not call cam_periph_error() in that case. We
need to make sure that the device gets unfrozen if needed though (in
case of actual errors, cam_periph_error() does this on our behalf).
Not objected by: mjacob (who currently doesn't have the time to
review the patch)
