It seems the EEE made RX MAC enter LPI(Low Power Idle) mode such
that dwc(4) was not able to receive packets. Ideally dwc(4) should
be able to use EEE to save power during periods of low link
utilization(i.e. gating off clock). Due to lack of dwc(4)
datasheet it's not easy to take required steps for EEE on LPI
enter/exit events. Disabling EEE in PHY seems to be easy
workaround until dwc(4) supports EEE.
Updating EEE advertisement register on RTL8211F seems to have no
effect until reprogramming MII_ANAR, MII_100T2CR and MII_BMCR
with auto-negotiation. It's not clear whether it's related with
mii_phy_reset()'s BMCR_ISO handling for RTL8211F though.
It seems rgephy_reset() needs careful investigation for newer
RealTek PHYs.
Ganbold submitted working version based on NetBSD change and
tested lots of changes I made. Thanks a lot!
Submitted by: ganbold (initial version)
In collaboration with: ganbold
Gleaned from a public header file. 5402 and 5404 look like they may be
used on embedded devices. 5478 and 5488 are switch PHYs. 5754 change is just
to note a product alias.
Differential Revision: https://reviews.freebsd.org/D3338
Submitted by: kevin.bowling@kev009.com
o rev. 1.10: Nuke trailing whitespace.
o rev. 1.15: Fix typo in comment.
o rev. 1.16: Add the following registers from IEEE 802.3-2009 Clause 22:
- PSE control register (0x0b)
- PSE status register (0x0c)
- MMD access control register (0x0d)
- MMD access address data register (0x0e)
o rev. 1.17 (comments only): The bit location of link ability is different
between 1000Base-X and others (see Annex 28B.2 and 28D).
o rev. 1.18: Nuke dupe word.
Obtained from: NetBSD
MFC after: 1 week
Sponsored by: genua mbh
the index array, not a value for BMCR register. In case of IFM_10_T there
could be either MII_MEDIA_10_T or MII_MEDIA_10_T_FDX, which are 1 and 2,
accordingly. Neither matches a valid BMCR value. My guessing is that this
write is harmless, since later mii_phy_setmedia() would write a proper
value there.
The code is here since the initial checkin. Note that case IFM_100_TX has
the same comment, but a proper value of BMCR_ISO is written. So, collapse
two cases into one, always writing there BMCR_ISO.
Sponsored by: Nginx, Inc.
set any value to ifm_data. If brgphy ever to call mii_phy_setmedia(),
then the value of BRGPHY_S1000 | BRGPHY_BMCR_FDX will trigger KASSERT.
While here, remove the obfuscating macro and wrap long lines.
Sponsored by: Nginx, Inc.
driver name and NIC driver softc via the device(9) tree,
instead of going dirty through the ifnet(9) layer.
Differential Revision: D1506
Reviewed by: imp, jhb
in userland rename in-kernel getenv()/setenv() to kern_setenv()/kern_getenv().
This fixes a namespace collision with libc symbols.
Submitted by: kmacy
Tested by: make universe
and keep both converted to drvapi and non-converted drivers
compilable.
o Make if_t typedef to struct ifnet *.
o Remove shim functions.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
interface allows the ifnet structure to be defined as an opaque
type in NIC drivers. This then allows the ifnet structure to be
changed without a need to change or recompile NIC drivers.
Put differently, NIC drivers can be written and compiled once and
be used with different network stack implementations, provided of
course that those network stack implementations have an API and
ABI compatible interface.
This commit introduces the 'if_t' type to replace 'struct ifnet *'
as the type of a network interface. The 'if_t' type is defined as
'void *' to enable the compiler to perform type conversion to
'struct ifnet *' and vice versa where needed and without warnings.
The functions that implement the API are the only functions that
need to have an explicit cast.
The MII code has been converted to use the driver API to avoid
unnecessary code churn. Code churn comes from having to work with
both converted and unconverted drivers in correlation with having
callback functions that take an interface. By converting the MII
code first, the callback functions can be defined so that the
compiler will perform the typecasts automatically.
As soon as all drivers have been converted, the if_t type can be
redefined as needed and the API functions can be fix to not need
an explicit cast.
The immediate benefactors of this change are:
1. Juniper Networks - The network stack implementation in Junos
is entirely different from FreeBSD's one and this change
allows Juniper to build "stock" NIC drivers that can be used
in combination with both the FreeBSD and Junos stacks.
2. FreeBSD - This change opens the door towards changing ifnet
and implementing new features and optimizations in the network
stack without it requiring a change in the many NIC drivers
FreeBSD has.
Submitted by: Anuranjan Shukla <anshukla@juniper.net>
Reviewed by: glebius@
Obtained from: Juniper Networks, Inc.
I don't have a copy of data sheet so I'm not sure exact PHY model
name. Vendor's web page indicates RTL8251 is latest PHY so I used
the name. This PHY is used with RTL8168G, RTL8168GU and RTL8411B.
interface. Make MII drivers forget about 'struct ifnet'.
Later plan is to provide an administrative downcall from ifnet
layer into drivers, to inform them about administrative status
change. If someone thinks that processing MII events for an
administratively down interface is a big problem, then drivers
would turn MII processing off.
The following MII drivers do evil things, like strcmp() on
driver name, so they still need knowledge of ifnet and thus
include if_var.h. They all need to be fixed:
sys/dev/mii/brgphy.c
sys/dev/mii/e1000phy.c
sys/dev/mii/ip1000phy.c
sys/dev/mii/jmphy.c
sys/dev/mii/nsphy.c
sys/dev/mii/rgephy.c
sys/dev/mii/truephy.c
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
auto-correction. This change makes re(4) establish a link with
a system using non-crossover UTP cable.
Tested by: Michael BlackHeart < amdmiek <> gmail dot com >
Unfortunately 5720S uses 5709S PHY id so add a hack to detect 5720S
PHY by checking parent device name. 5720S PHY does not support 2500SX.
Tested by: Geans Pin < geanspin <> broadcom dot com >
them, please let me know if not). Most of these are of the form:
static const struct bzzt_type {
[...list of members...]
} const bzzt_devs[] = {
[...list of initializers...]
};
The second const is unnecessary, as arrays cannot be modified anyway,
and if the elements are const, the whole thing is const automatically
(e.g. it is placed in .rodata).
I have verified this does not change the binary output of a full kernel
build (except for build timestamps embedded in the object files).
Reviewed by: yongari, marius
MFC after: 1 week
handling(jumbo, wire speed etc) in brgphy_reset(). Touching
BRGPHY_MII_AUXCTL register seems to confuse APE firmware such that
it couldn't establish a link.
extract a link status of PHY when parent driver is re(4).
RGEPHY_MII_SSR register does not seem to report correct PHY status
on some integrated PHYs used with re(4).
Unfortunately, RealTek PHYs have no additional information to
differentiate integrated PHYs from external ones so relying on PHY
model number is not enough to know that. However, it seems
RGEPHY_MII_SSR register exists for external RealTek PHYs so
checking parent driver would be good indication to know which PHY
was used. In other words, for non-re(4) controllers, the PHY is
external one and its revision number is greater than or equal to 2.
This change fixes intermittent link UP/DOWN messages reported on
RTL8169 controller.
Also, mii_attach(9) is tried after setting interface name since
rgephy(4) have to know parent driver name.
PR: kern/165509
found on Adaptec AIC-6915 Starfire ethernet controller.
While here, use status register to know resolved speed/duplex.
With this change, sf(4) correctly reports speed/duplex of
established link.
Reviewed by: marius
- In case the parent is bge(4), don't set the Jumbo frame settings unless
the MAC actually is Jumbo capable as otherwise the PHY might not have the
corresponding registers implemented. This is also in line with what the
Linux tg3 driver does.
PR: 165032
Submitted by: Alexander Milanov
Obtained from: OpenBSD
MFC after: 3 days
before calling bus_enumerate_hinted_children(9) (which is the minimum for
this to work) instead of fully probing it so later on we can just call
bus_generic_attach(9) on the parent of the miibus(4) instance. The latter
is necessary in order to work around what seems to be a bzzarre race in
newbus affecting a few machines since r227687, causing no driver being
probed for the newly added miibus(4) instance. Presumably this is the
same race that was the motivation for the work around done in r215348.
Reported and tested by: yongari
- Revert the removal of a static in r221913 in order to help compilers to
produce more optimal code.
issues probably needing workarounds in bge(4) when brgphy(4) handles this
PHY. Letting ukphy(4) handle it instead results in a working configuration,
although likely with performance penalties.
