With more than 1 AP present, an AP could fail to properly release
the mp lock before waiting for smp_started to become nonzero.
With early startup of APs, the BSP could fail to properly release
the mp lock before waiting for smp_started to become nonzero.
panicing and return a status so that we can decide whether to drop
into DDB or panic. If the status from isa_nmi is true, panic the
kernel based on machdep.panic_on_nmi, otherwise if DDB is
enabled, drop to DDB based on machdep.ddb_on_nmi.
Reviewed by: peter, phk
Don't allow cpu entries in the MP table to contain APIC IDs out of range.
Don't write outside array boundaries if an IO APIC entry in the MP table
contains an APIC ID out of range.
Assign APIC IDs for all IO APICs according to section 3.6.6 in the
Intel MP spec:
- If the current APIC ID on an IO APIC doesn't conflict with other
IO APICs or CPUs, that APIC ID should be used. The copy of the MP
table must be updated if the corresponding APIC ID in the MP table
is different.
- If the current APIC ID was in conflict with other units, the
corresponding APIC ID specified in the MP table is checked for conflict.
- If a conflict is still found then fall back to using a new unique ID.
The copy of the MP table must be updated.
- IDs out of range is considered to be in conflict.
During these operations, the IO_TO_ID array cannot be used, since any
conflict would have caused information loss. The array is then corrected,
since all APIC ID conflicts should have been resolved.
PR: 20312, 18919
display control by apm -d.
- Remove APM_DEBUG to avoid re-build kernel with such a unspported optioin.
- Introduce new denug flag `debug.apm_debug' which can be controlled by
sysctl interface and loader by setting like "debug.apm_debug=1", you
will get debug messages from APM driver.
- Add some enhancements from linux on display control by apm -d. I'm
expecting that we can see some improvements on some laptops where
apm -d doesn't work correctly so far.
Reviewed by: -mobile and -current folks (no objection)
Suggested by: Susumu WAKABAYASHI <susumu@wakabaya.net>
gcc's internal exit() prototypes and the (futile) hackery that we did to
try and avoid warnings. main() was renamed for similar reasons.
Remove an exit related hack from makesyscalls.sh.
to construct a path that was long enough (ie longer than
SPARE_USRSPACE bytes) and trash the stack.
Note that SPARE_USRSPACE is much smaller than MAXPATHLEN so that
the Linuxulator will now return ENAMETOOLONG even if the path
is smaller than MAXPATHLEN.
PR: 12749
due to a paucity of IRQs. I have some reservations about this, so I'm
not going to MFC this just yet. I'm doing this to see how many
problems it causes so we can do this in 4.2. I've been seeing hangs
on my laptop from time to time, but sometimes it was not in polling
mode, other tmies it was. Don't know if this is one problem or more
than one.
Requested by: Sean O Connell
is not needed since the FreeBSD native implementation switched
from TIOC{G|S}PGRP to FIO{G|S}ETOWN (kern_descrip.c rev 1.55).
PR: 16946
Submitted by: Victor Salaman <salaman@teknos.com>
a NMI occured, you could type continue in DDB and the kernel would
not attempt to detect what type of NMI was recieved. Now we check
for the type of NMI first and then go to DDB if it is enabled.
This will solve the problem with having DDB enabled and getting an
NMI due to some possibly bad error and being able to continue the
operation of the kernel when you really want to panic and know
what happened.
Submitted by: jhb
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
Currently, many drivers support more than one bus of ISA, EISA, MCA,
PCI.
Before this commit, we had, for example, some SCSI devices listed more
than once, iirc, some up to three times (ISA/EISA, MCA, PCI).
Since now the "device" line is common for all of them and they only
differ for the hints stuff, I did the following:
First, list Busses: (E)ISA, MCA, PCI and explain, that only ISA
needs the hints stuff.
Move NIC/SCSI stuff, which were the only split sections, behind these
stuff. Describe all drivers only one time and list all supported
chips.
List all device (+ hints for ISA, if possible).
I've also added few additional supported chips to some drivers, xl for
example and some SCSI drivers.
Also, softupdates is no longer disabled by default, so the comment should
not say, it's not enabled by default due to license issues.
Approved by: asmodai
To come: include PAO devices (imp volunteered for help)
set equal to the number of kilobytes in your cache. The old options are
still supported for backwards compatibility.
Submitted by: Kelly Yancey <kbyanc@posi.net>
