This machine uses a non-standard scheme to specify the interrupts to
be assigned for devices in PCI slots; instead of giving the INO
or full interrupt number (which is done for the other devices in this
box), the firmware interrupt properties contain intpin numbers, which
have to be swizzled as usual on PCI-PCI bridges; however, the PCI host
bridge nodes have no interrupt map, so we need to guess the
correct INO by slot number of the device or the closest PCI-PCI
bridge leading to it, and the intpin.
To do this, this fix makes the following changes:
- Add a newbus method for sparc64 PCI host bridges to guess
the INO, and glue code in ofw_pci_orb_callback() to invoke it based
on a new quirk entry. The guessing is only done for interrupt numbers
too low to contain any IGN found on e450s.
- Create another new quirk entry was created to prevent mapping of EBus
interrupts at PCI level; the e450 has full INOs in the interrupt
properties of EBus devices, so trying to remap them could cause
problems.
- Set both quirk entries for e450s; remove the no-swizzle entry.
- Determine the psycho half (bus A or B) a driver instance manages
in psycho_attach()
- Implement the new guessing method for psycho, using the slot number,
psycho half and property value (intpin).
Thanks go to the testers, especially Brian Denehy, who tested many kernels
for me until I had found the right workaround.
Tested by: Brian Denehy <B.Denehy@90east.com>, jake, fenner,
Marius Strobl <marius@alchemy.franken.de>,
Marian Dobre <mari@onix.ro>
Approved by: re (scottl)
The current name is confusing, because it indicates to
the client that a bus_dmamap_sync() operation is not
necessary when the flag is specified, which is wrong.
The main purpose of this flag is to hint the underlying
architecture that DMA memory should be mapped in a coherent
way, but the architecture can ignore it. But if the
architecture does supports coherent mapping of memory, then
it makes bus_dmamap_sync() calls cheap.
This flag is the same as the one in NetBSD's Bus DMA.
Reviewed by: gibbs, scottl, des (implicitly)
Approved by: re@ (jhb)
value to be written into tick_compare in tick_hardclock(). While
we were taking care that the value to be written was at least TICK_GRACE
ticks in the future, a vector interrupt could happen between calculating
the value and writing it. If it took longer than TICK_GRACE to complete
(which is doubtful for a single device-triggered vector interrupt, but
quite likely for some IPIs), the value written would be in the past
and tick interrupts (which drive hardclock and statclock) would stop
until %tick wraps around, which takes a long time.
Also, increase TICK_GRACE from 1000 to 10000 for good measure.
Reported by: kris
Reviewed by: jake
Approved by: re (scottl)
BUS_DMASYNC_ definitions remain as before. The does not change the ABI,
and reverts the API to be a bit more compatible and flexible. This has
survived a full 'make universe'.
Approved by: re (bmah)
- Fix visibilty test for LONG_BIT and WORD_BIT. `#if defined(__FOO_VISIBLE)'
is alays wrong because __FOO_VISIBLE is always defined (to 0 for
invisibility).
sys/<arch>/include/limits.h
sys/<arch>/include/_limits.h:
- Style fixes.
Submitted by: bde
Reviewed by: bsdmike
Approved by: re (scottl)
- Move struct sigacts out of the u-area and malloc() it using the
M_SUBPROC malloc bucket.
- Add a small sigacts_*() API for managing sigacts structures: sigacts_alloc(),
sigacts_free(), sigacts_copy(), sigacts_share(), and sigacts_shared().
- Remove the p_sigignore, p_sigacts, and p_sigcatch macros.
- Add a mutex to struct sigacts that protects all the members of the struct.
- Add sigacts locking.
- Remove Giant from nosys(), kill(), killpg(), and kern_sigaction() now
that sigacts is locked.
- Several in-kernel functions such as psignal(), tdsignal(), trapsignal(),
and thread_stopped() are now MP safe.
Reviewed by: arch@
Approved by: re (rwatson)
Remove DBL_DIG, DBL_MIN, DBL_MAX and their FLT_ counterparts, they
were marked for deprecation ever since SUSv1 at least.
Only define ULLONG_MIN/MAX and LLONG_MAX if long long type is
supported.
Restore a lost comment in MI _limits.h file and remove it from
sys/limits.h where it does not belong.
quite excessive, and caused the available space to be used up too
easily. The new limit should be a better estimation of how much the
caller will need at most.
- Double the IOTSB size 64kB, for a DVMA area size of 64MB.
This should fix DMA problems on e450s and other large machines due
to DVMA space exhaustion, which were introduced in my last IOMMU
code revision in January.
Reported and tested by: fenner
that were added to sparc64 and later powerpc, really should have been in
the MI area. But changing that now with insufficient preperation will
just cause too much pain.
Move MD_FETCH() to the MI sys/linker.h file to avoid another two copies
of it.
syscall return values should be cleared. The system calls
getcontext() and swapcontext() want to return 0 on success
but these contexts can be switched to at a later time so
the return values need to be cleared in the saved register
sets. Other callers of get_mcontext() would normally want
the context without clearing the return values.
Remove the i386-specific context saving from the KSE code.
get_mcontext() is not i386-specific any more.
Fix a bad pointer in the alpha get_mcontext() code. The
context was being bcopy()'d from &td->tf_frame, but tf_frame
is itself a pointer, so the thread was being copied instead.
Spotted by jake.
Glanced at by: jake
Reviewed by: bde (months ago)
to get actual constant values. This is in preparation for machine/limits.h
retirement.
Discussed on: standards@
Submitted by: Craig Rodrigues <rodrigc@attbi.com> (*)
Modified by: kan
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
the cpu dependent files. It will need to be done differently for USIII.
- Simplify the logic for detecting context rollovers. Instead of dealing
with it when the next context switch would cause the context numbers to
rollover, deal with it when they actually do rollover.
- Move some things around in cpu_switch so that we only do 1 membar #Sync
when switching address space, instead of 2.
- Detect kernel threads by comparing the new vm space to vmspace0, instead
if checking if the tlb context is 0.
- Removed some debug code.
enum to an int and redefine the BUS_DMASYNC_* constants as
flags. This allows us to specify several operations in one
call to bus_dmamap_sync() as in NetBSD.
of asserting that an mbuf has a packet header. Use it instead of hand-
rolled versions wherever applicable.
Submitted by: Hiten Pandya <hiten@unixdaemons.com>
These are called through function pointers so that different implementations
can be provided for cheetah, where the block load instructions may or may
not be a win, and so they can be disabled with the machdep.use_vis tunable.
In terms of raw bandwidth the integer versions are faster, but not allocating
lines in the L2 cache for useless data gives a measurable improvement in user
time for the benchmarks I tested (mostly buildworld with -j8).
As far as I can tell the instructions used are implemented on everything
back to UltraSPARC I, so there should not be a problem with different cpu
types.
to take care of the KAME IPv6 code which needs ovbcopy() because NetBSD's
bcopy() doesn't handle overlap like ours.
Remove all implementations of ovbcopy().
Previously, bzero was a function pointer on i386, to save a jmp to
bzero_vector. Get rid of this microoptimization as it only confuses
things, adds machine-dependent code to an MD header, and doesn't really
save all that much.
This commit does not add my pagezero() / pagecopy() code.
can do 64 bytes at a time and don't allocate lines in the L2 cache. These
assume that everything is 64 byte aligned, and that there's more than 128
bytes of data (best for whole pages). The block load and store instructions
don't follow normal memory ordering rules and require either a memory barrier
or move between registers before the data can actually be used. This
implementation correctly shuffles around 3 out of the 4 sets of registers
in order to avoid memory barriers expect for the last 2 blocks.
will be saved if we context switch as a result of an interrupt which occured
while using the floating point registers in the kernel (which actually can't
happen right now). This allows fp disabled traps in the kernel, which
normally shouldn't happen, so make sure the trapping code is what we expect
it is.
used to support block copy and zero operations in the kernel which use the
floating point registers.
- While I'm changing the size, improve the layout of struct pcb, sort by size,
then alphabetical etc.
- Add some assertions to validate assumptions made about how the pcb is
allocated.
for temporaries relating to the state of the new process instead of the
outs, so that functions can be called without fear of clobbering them.
- Use savefpctx instead of rolling our own.
