1.6 2000/04/12 21:07:55 scw
Add support for the SOHOware PCMCIA Ethernet card, model ND5100-E.
This seems to be a re-badged NDC (National Datacomms. Corp) card.
It needs a quirk entry due to lack of manufacturer tuple in the CIS.
For some reason, the 'Tx/Rx' LED on the connector module is inverted
such that it is off during network activity...
bus/slot/function numbers. The old PCI code used other markers or
something, but without it here under the new pci code it is very hard to
tell which device is which (this only affects bootverbose mode).
PR kern/20895:
- Add FE_DAC new feature flag to distinguish between
64 bit PCI addressing (DAC cycles) and 64 bit PCI
interface (64 bit Memory BARs).
- Properly deal with chips that have a 32 bit PCI
interface but support and may generate DAC.
(Only SYM53C895A for now).
PR misc/17584 (at least partially addressed):
- Try detecting hardware combinations that trigger
spurious PCI master parity error detections by the
PCI chip. This work-around is implemented in the
`snooptest' routine and consists in retrying with
PCI master parity checking disabled if such an
error is reported by the PCI chip during this test.
Other:
- Fix a tiny bug in WIDE negotiation that was very
unlikely to be triggerred. The BUS width was wrongly
compared against chip's max. offset.
#includes "smbus.h". There is still some bogus (but harmless) stuff
here surrounding the #include <sys/bus.h> includes here and elsewhere in
the bktr code.
cloning infrastructure standard in kern_conf. Modules are now
the same with or without devfs support.
If you need to detect if devfs is present, in modules or elsewhere,
check the integer variable "devfs_present".
This happily removes an ugly hack from kern/vfs_conf.c.
This forces a rename of the eventhandler and the standard clone
helper function.
Include <sys/eventhandler.h> in <sys/conf.h>: it's a helper #include
like <sys/queue.h>
Remove all #includes of opt_devfs.h they no longer matter.
the link and activity LED control bits in CSR15 in order for the
controller to drive the LEDs correctly. This was largely done for the
ZNYX multiport cards, but should also work with the DEC DE500-BA
and other non-MII cards.
enable bit hasn't been set in the command register, set the bit and
honour the register. It seems that quite a few lazy BIOS writers
aren't bothering to do this, which upsets the existing code and causes
us to miss out on properly-configured devices.
pcib instance is initialized because accesses to PCI_Config region can
occur during ACPI initialization.
Note that this is a short term solution, more consideration will be
required in order to integrate ACPI into the newbus probe sequence.
change channel interface - kobj implementation coming soonish
make pcm_makelinks not panic if modular
add pcm_unregister()
these changes support newpcm kld unloading, but this is only implemented
by ds1.c
This provides support for the Adaptec SCSI RAID controller family,
as well as the DPT SmartRAID V and VI families.
The driver will be maintained by Mark and Adaptec, and any changes
should be referred to the MAINTAINER.
- Remove DELAY() kludge before power off.
- Move EVENTHANDLER_REGISTER to acpi_attach().
- Pass RB_POWEROFF flag to shutdown_nice().
Reviewed by: msmith
kernel can instigate an orderly shutdown but still determine the form of
that shutdown. Make it possible eg. to cleanly shutdown and power off the
system under ACPI when the power button is pressed.
- New support for 40LD firmware found in Series 475 and 471 adapters.
- Better support for 8LD firmware adapters
- Ioctl passthrough interface for userland utilities.
- Improved error handling and queueing.
- Several bugfixes (including the 'still open' shutdown bug and
closing some small race conditions).
- Zone-style command allocator, reducing memory wasted under heavy
load conditions.
- CAM interface (disabled and not fully working) for SCSI passthrough
access to non-disk devices
Thanks to AMI for supplying a pile of new adapters and various other
help in making this happen.
- Add new funcions for device state stuff;
acpi_get_current_device_state() and acpi_set_device_state()
- Add new funcions for power resource stuff;
acpi_powerres_init(), acpi_powerres_debug(),
acpi_get_current_powerres_state() and acpi_set_powerres_state()
These were implemented based on 7.1, 7.2, 7.2.2, 7.2.3, 7.2.4, 7.3,
7.3.3, 7.4, 7.4.1, 7.4.2, 7.4.3 and 7.5 of ACPI spec 1.0b.
- The "Osd*" stuff went away from acpi driver code, use the bus_space
functions directly instead.
- Fix minor english bugs.
acpi_registers_input -> acpi_register_input
acpi_registers_output -> acpi_register_output
- Remove all magic numbers for the sleeping states. We now have
#defines for these.
- NULL is treated the same as the return from aml_get_rootname in
aml_find_from_namespace().
Suggested by: msmith
Thanks mike!
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
possible complications with the forthcoming DRI code, and feel that DRI
should handle the device-level interaction. Read
http://people.FreeBSD.org/~cokane/3dfx.html
to find out more. Basically want to move toward using OpenGL and DRI for
everything on these cards. Added a few defines and spacing style fixes in
tdfx_vars.h
o Sync to NetBSD (rev NetBSD-user edited-log):
1.97 onoe add Samsung MagicLAN SWL-2000N
1.96 gmcgarry Add entries for all Xircom ethernet models.
1.95 onoe Add Farallon SkyLINE 11mb card as Intersil Prism2 [...]
1.94 joda add 3Com 3CRWE737A (AirConnect)
1.93 soren Include vendor name for IBM products.
1.92 onoe Add Farallon SkyLINE Wireless LAN Card for awi(4) [...]
1.91 soren Add Olicom GoCard.
1.90 gmcgarry Clean up XIRCOM entries
- Add entry for Xircom CreditCard Ethernet + Modem 28
- Add entry for Intel EtherExpress PRO/100
- Add entry for Compaq Netelligent 10/100 Ethernet
1.89 is RATOC REX-R280 (another if_mbe_pcmcia card) support by [...]
1.88 joda Panasonic KXLC003
1.87 scw [...] SOHOware PCMCIA Ethernet card, model ND5100-E [...]
1.86 itojun add CIS for Corega Wireless LAN PCC-11 [...]
o Minor diffs between the two files corrected to aid future sync.
modify driver capability reporting format to list every audio format
seperately- required for above and because we could not previously indicate
that mono was unsupported.
there should be no functional impact.
Remove old DEVFS support fields from dev_t.
Make uid, gid & mode members of dev_t and set them in make_dev().
Use correct uid, gid & mode in make_dev in disk minilayer.
Add support for registering alias names for a dev_t using the
new function make_dev_alias(). These will show up as symlinks
in DEVFS.
Use makedev() rather than make_dev() for MFSs magic devices to prevent
DEVFS from noticing this abuse.
Add a field for DEVFS inode number in dev_t.
Add new DEVFS in fs/devfs.
Add devfs cloning to:
disk minilayer (ie: ad(4), sd(4), cd(4) etc etc)
md(4), tun(4), bpf(4), fd(4)
If DEVFS add -d flag to /sbin/inits args to make it mount devfs.
Add commented out DEVFS to GENERIC
that should be better.
The old code counted references to mbuf clusters by using the offset
of the cluster from the start of memory allocated for mbufs and
clusters as an index into an array of chars, which did the reference
counting. If the external storage was not a cluster then reference
counting had to be done by the code using that external storage.
NetBSD's system of linked lists of mbufs was cosidered, but Alfred
felt it would have locking issues when the kernel was made more
SMP friendly.
The system implimented uses a pool of unions to track external
storage. The union contains an int for counting the references and
a pointer for forming a free list. The reference counts are
incremented and decremented atomically and so should be SMP friendly.
This system can track reference counts for any sort of external
storage.
Access to the reference counting stuff is now through macros defined
in mbuf.h, so it should be easier to make changes to the system in
the future.
The possibility of storing the reference count in one of the
referencing mbufs was considered, but was rejected 'cos it would
often leave extra mbufs allocated. Storing the reference count in
the cluster was also considered, but because the external storage
may not be a cluster this isn't an option.
The size of the pool of reference counters is available in the
stats provided by "netstat -m".
PR: 19866
Submitted by: Bosko Milekic <bmilekic@dsuper.net>
Reviewed by: alfred (glanced at by others on -net)
has the side effect of detaching the children before I delete them.
When I put the last commits in a loop for loop it died after 5 or so
iterations. After this change, I lasted 50 before I stopped the test.
Add pcic_detach which removes all of the pcic's children.
This lets me load/unload pcic multiple times w/o having multiple
instances of each slot attached to pcic.
problems). Also pick an irq if one isn't specified. Ditto for
memory.
Add additional printfs in the error paths. These will disappear in time.
There are still some panics, but this is a good checkpoint.
some of the fake devices sometimes seen on single device ATA
channels.
Proberly fail on failures in ata-disk.c, retry instead of hang.
Cleanup the VIA probe/init code a bit.
Fix a couble of missing free's in atapi-cd.c in the changer code.
Add support for AMD RAID controllers as "disks".
Requested-by: Marius Bendiksen <mbendiks@eunet.no>
Remove potential panic when attempting to open non-existent drivers.
init_drive: Return error codes correctly. Previously it would
occasionally return 0. The error was redetected
elsewhere, but this was causing a number of confusing
error messages.
Add support for wi(4) compatible configuration interface. It enables
wicontrol(8) to configure some 802.11 specific parameters.
Some minor fixes from NetBSD.
Obtained from: NetBSD current
in bogus hwptr warnings. Further comments sought on -hackers
were not forthcoming. I can only hope that calling DELAY() like
this doesn't cause any heartburn.
Make the umass driver depend on this module.
Makes it possible to compile the kernel without SCSI support and load it
when for example a USB floppy is conencted.
Make it possible to move a device to its unconfigured state by
using config #0.
Add some comments.
Change error reporting in port reset function.
usbd_devinfo_vp(): search the know devs array also if the device doesn't
return product description (e.g. Kye's Genius NetScroll mouse returns
vendor, but not product); the strings returned by device are still
preferred to those in the array, though
understand exactly what it is about SMPng that tickles this bug. What I
do know is that the foo_init() routine in most drivers is often called
twice when an interface is brought up. One time is due to the ifconfig(8)
command calling the SIOCSIFFLAGS ioctl to set the IFF_UP flag, and another
is probably due to the kernel calling ifp->if_init at some point. In any
case, the SMPng changes seem to affect the timing of these two events in
such a way that there is a significant delay before any packets are sent
onto the wire after the interface is first brought up. This manifested
itself locally as an SMPng test machine which failed to obtain an address
via DHCP when booting up.
It looks like the second call to fxp_init() is happening faster now than
it did before, and I think it catches the chip while it's in the process
of dealing with the configuration command from the first call. Whatever
the case, a FXP_CSR_SCB_CNA interrupt event is now generated shortly after
the second fxp_init() call. (This interrupt is apparently never generated
by a non-SMPng kernel, so nobody noticed.)
There are two problems with this: first, fxp_intr() does not handle the
FXP_CSR_SCB_CNA interrupt event (it never tests for it or does anything
to deal with it), and second, the meaning of FXP_CSR_SCB_CNA is not
documented in the driver. (Apparently it means "command unit not active.")
Bad coder. No biscuit.
The fix is to have the FXP_CSR_SCB_CNA interrupt handled just like the
FXP_SCB_STATACK_CXTNO interrupt. This prevents the state machine for
the configuration/RX filter programming stuff from getting wedged for
several seconds and preventing packet transmission.
Noticed by: jhb
This is done by misusing the device minor a bit to encode the
track no there.
So to read track #4 just use /dev/acdNt4 where N is the device #.
The driver no automatically sets the blocksize (sectorsize) to
what the track is set to in the TOC.
This has the nice effect that you can now rip audioi tracks
by simply doing:
dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352
it cant be much simpler than that :)
NOTE: the original acdNa & acdNc device still work as usual,
except the blocksize is set according to track0.
from the SCSI id it has. (this avoids the confusing umass-sim32 device. It
should have been umass-sim0 all along (there is only one), and if it is
spoken to as a SCSI device the sim should be umass32.
Make the rescan actually work. We need to fill in a target and lun wildcard
and not the SCSI id of the SIM.
Add a seatbelt.
position, channel 1's dma position register must be quiescent. So
the driver will spl, pause the DMA, delay a bit and hold as still as
possible while snapping the picture.
I'm sure there HAS to be a better way to do this, but if there is, it's
not documented.
So far as I can tell, this fixes recording, which means the Solo is open
for business.
cases the registers are not correctly set on resume.
This solves the problem of USB failing after resuming a machine.
Submitted by: mike+fbsd@medianstrip.net
PR: 18261
Promise Ultra100 / Fasttrak100
HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100)
Intel ICH2 (Intel 815E based motherboards)
So far I can read >90MB/s on the Promise and the HPT370.
I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems
writing is still done in ATA66 mode :(
The ICH2 support is untested as of yet...
modules to depend on modules in the same file (uhub depends on usb) or
even on themselves (usb on usb, makes the define in usb_port.h a lot
less convoluted).
Use ANSI prototypes.
the scratch RAM for data normally found in the SEEPROM (presumably in the
event that the SEEPROM is unavailable or can't be read). This code causes
a spontaneous reboot on monster.osd.bsdi.com, which has an embedded aic7880
controller. The problem appears to happen either when it writes to the
SCBPTR port and then reads from the SCB_CONTROL port. Somewhere during
the inb/outb operations, the system has a heart attack and restarts.
This code looks very suspicious, particularly since it has unconditionalized
debug mesages such as "Got here!" and "And it even worked!". With this
block #ifdef'ed out, the machine boots and runs properly. I stronly suggest
that it stay #ifdef'ed out until it's properly tested.
opens if the reference count is not decremented on close.
Note that this may result in the reference count being corrupted
on full duplex devices (due to mismatching opens/closes), but the
code doesn't use the reference count for anything on full duplex
devices.
2. Offer half duplex with both playback and record on channel 1 or
full duplex with playback always on channel 2 as a compile-time option.
3. 16 bit record output is byte swapped for some dumb reason. Report the _BE
AFMTs for recording.
if you kldload this driver, all the subordinate devices are probed/attached
as expected. But this is not the case when the driver is statically compiled
into the kernel. Since I do most of my testing with modules, I failed to
notice this. I'm not sure if it's intended behavior or not. I think it may
be, but it seems a little counter-intuitive.
16 bit samples have some sort of choppiness, the nature of which
is not completely clear, but it clearly has something to do with
dma buffer synchronization. But at least channel 1 makes noise now.
appears to be the correct length, but quality of output has not yet
been tested. Also, full duplex audio (that is, playback on channel 1)
does not yet work. Two constants and I am there!
Obtained from: major hints from ALSA
with LEDs on some cards being stomped on when clearing the "jabber disable"
bit. Using DC_SETBIT() has an unwanted side effect of setting a write enable
bit in the watchdog timer register which we really want to be cleared when
we do a write.
changes is that there's now a Solaris port of this driver, so some things
in the core version had to change (not much, but some).
In order, from the top.....:
A lot of error strings are gathered in one place at the head of the file.
This caused me to rewrite them to look consistent (with respect to
things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'.
The major mailbox function, isp_mboxcmd, now takes a third argument,
which is a mask that selectively says whether mailbox command failures
will be logged. This will substantially reduce a lot of spurious noise
from the driver.
At the first run through isp_reset we used to try and get the current
running firmware's revision by issuing a mailbox command. This would
invariably fail on alpha's with anything but a Qlogic 1040 since SRM
doesn't *start* the f/w on these cards. Instead, we now see whether we're
sitting ROM state before trying to get a running BIOS loaded f/w version.
All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to
isp_prt. There are seperate print levels that can be independently
set (see ispvar.h), which include debugging, etc.
All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and
RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel
cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry
indices, so we can make a 1024 entry index for them instead of the
256 entries we've had until now.
A major change it to fix isp_fclink_test to actually only wait the
delay of time specified in the microsecond argument being passed.
The problem has always been that a call to isp_mboxcmd to get he
current firmware state takes an unknown (sometimes long) amount of
time- this is if the firmware is busy doing PLOGIs while we ask
it what's up. So, up until now, the usdelay argument has been
a joke. The net effect has been that if you boot without being plugged
into a good loop or into a switch, you hang. Massively annonying, and
hard to fix because the actual time delta was impossible to know
from just guessing. Now, using the new GET_NANOTIME macros, a precise
and measured amount of USEC_DELAY calls are done so that only the
specified usecdelay is allowed to pass. This means that if the initial
startup of the firmware if followed by a call from isp_freebsd.c:isp_attach
to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000,
no more than two seconds will actually elapse before we leave concluding
that the cable is unhooked. Jeez. About time....
Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE
macro to a call to the platform supplied isp_done (sane naming).
Limit our size of request queue completions we'll look at at interrupt
time. Since we've increased the size of the Request Queue (and the
size of the Response Queue proportionally), let's not create an
interrupt stack overflow by having to keep a max completion list
(forw links are not an option because this is common code with
some platforms that don't have link space in their XS_T structures).
A limit of 32 is not unreasonable- I doubt there'd be even this many
request queue completions at a time- remember, most boards now use
fast posting for normal command completion instead of filling out
response queue entries.
In the isp_mboxcmd cleanup, also create an array of command
names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8".
Remove the isp_lostcmd function- it's been deprecated for a while.
Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus
register dump fucntion.
Various other cleanups.
isp_prt calls. We now use an argument to the ISPCTL_FCLINK_TEST
call. We change all IDPRINTF macros to isp_prt calls. We add
the isp_prt function here.
quite a bit so that all of the ports have a similar set of required
macros/definitions (and in similar places in the isp_<platform>.h
file).
Some new macros/functions added- Mailbox Acquire/Relase macros,
NANOTIME macros, SNPRINTf and STRNCAT. MemoryBarrier beomes
MEMORYBARRIER with much stronger types.
