The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.
Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix
We read TX_STATUS1 to acknowledge a TX interrupt. We don't use this
value for anything, so mark it as unused. We may be able to eliminate
this read, but since this hardware is poorly documented and difficult to
test, I'm leaving the read in place.
Sponsored by: Netflix
bbp_atten is write-only: we don't use it later in
bwi_rf_calc_nrssi_slope_11b. However, we may also be able to eliminate
the read of this value from the device. However, The documationation for
this hardware is thing and I can't test this card so I've left the read
of this register in case it's required.
Sponsored by: Netflix
On architectures with strict alignment requirements (e.g. arm), clang 14
warns about a packed struct which encloses a non-packed union:
In file included from sys/dev/bwi/bwimac.c:79:
sys/dev/bwi/if_bwivar.h:308:7: error: field iv_val within 'struct bwi_fw_iv' is less aligned than 'union (unnamed union at sys/dev/bwi/if_bwivar.h:305:2)' and is usually due to 'struct bwi_fw_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
} iv_val;
^
It appears to help if you also add __packed to the inner union (i.e.
iv_val). No change to the layout is intended.
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D34196
In r178354 with the introduction of multi-bss ("vap") support factoring
out started and with r193340 ieee80211_media_change() no longer returned
ENETRESET but only 0 or error.
As ieee80211(9) tells the ieee80211_media_change() function should not
be called directly but is registered with ieee80211_vap_attach() instead.
Some drivers have not been fully converted. After fixing the return
checking some of these functions were simply wrappers between
ieee80211_vap_attach() and ieee80211_media_change(), so remove the extra
function, where possible as well.
PR: 248955
Submitted by: Tong Zhang (ztong0001 gmail.com) (original)
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Make sure all occurrences of ieee80211_input_xxx() in sys/dev are
covered by a network epoch section. Do not depend on the interrupt
handler nor any taskqueues being in a network epoch section.
This patch should unbreak the PCI WLAN drivers after r357004.
Pointy hat: glebius@
Sponsored by: Mellanox Technologies
- Alignment issues:
* Add missing __packed attributes + padding across all drivers; in
most places there was an assumption that padding will be always
minimally suitable; in few places - e.g., in urtw(4) / rtwn(4) -
padding was just missing.
* Add __aligned(8) attribute for all Rx radiotap headers since they can
contain 64-bit TSF timestamp; it cannot appear in Tx radiotap headers, so
just drop the attribute here. Refresh ieee80211_radiotap(9) man page
accordingly.
- Since net80211 automatically updates channel frequency / flags in
ieee80211_radiotap_chan_change() drop duplicate setup for these fields
in drivers.
Tested with Netgear WG111 v3 (urtw(4)), STA mode.
MFC after: 2 weeks
Wrap ieee80211_add_channel_list_2ghz into another function
which supplies default (1-14) channel list to it and drop
its copies from drivers.
Checked with RTL8188EE, country US / JP / KR / UA.
MFC after: 2 weeks
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
similar to "if (ticks > localvar+interval) {localvar=ticks; ...}" where
localvar is initialized to zero. Ticks is initialized to a negative value
since r278230, and that leads to these if statements never being true.
directly from the node.
- Use ni_txparms directly instead of calculating them manually every time
- Move M_EAPOL flag check upper; otherwise it may be skipped due to
'ucastrate' / 'mcastrate' check
- Use 'mgtrate' for control frames too (see ifconfig(8), mgtrate parameter)
- Add few more M_EAPOL checks where it was missing (zyd(4), ural(4),
urtw(4))
- Few unrelated cleanups
Tested with:
- Intel 6205 (iwn(4)), STA mode;
- WUSB54GC (rum(4)), HOSTAP mode + RTL8188EU (rtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9811
Replace various void * / int argument combinations with common structures:
- ieee80211_ratectl_tx_status for *_tx_complete();
- ieee80211_ratectl_tx_stats for *_tx_update();
While here, improve amrr_tx_update() for a bit:
1. In case, if receiver is not known (typical for Ralink USB drivers),
refresh Tx rate for all nodes on the interface.
2. There was a misuse:
- otus(4) sends non-decreasing counters (as originally intended);
- but ural(4), rum(4) and run(4) are using 'read & clear' registers
to obtain statistics for some period of time (and those 'last period'
values are used as arguments for tx_update()). If arguments are not big
enough, they are just discarded after the next call.
Fix: move counting into *_tx_update()
(now otus(4) will zero out all node counters after every tx_update() call)
Tested with:
- Intel 3945BG (wpi(4)), STA mode.
- WUSB54GC (rum(4)), STA / HOSTAP mode.
- RTL8188EU (urtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8037
No functional change, only trivial cases are done in this sweep,
Drivers that can get further enhancements will be done independently.
Discussed in: freebsd-current
This doesn't free the mbuf upon error; the driver ic_raw_xmit method is still
doing that.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3774
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
amount of memory.
- Don't request segsize of BUS_SPACE_MAXSIZE_32BIT, when maxsize is
MCLBYTES.
With this change bwi_attach() can succeed on i386.
Submitted by: scottl
The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
routines and thus assert if one passes in a rate code with the
high bit set.
Since the high bit can indicate either IEEE80211_RATE_BASIC or
IEEE80211_RATE_MCS, it's up to the caller to determine whether
the rate is 11n or not, and either mask out the BASIC bit, or
call a different function.
(Yes, this does mean that net80211 should grow 11n-aware rate2phytype()
and rate2plcp() functions..)
This may need to happen for the other drivers - it's currently only
done (now) for iwn(4) and bwi(4).
PR: kern/181100