The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.
Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
Make sure all occurrences of ieee80211_input_xxx() in sys/dev are
covered by a network epoch section. Do not depend on the interrupt
handler nor any taskqueues being in a network epoch section.
This patch should unbreak the PCI WLAN drivers after r357004.
Pointy hat: glebius@
Sponsored by: Mellanox Technologies
- Alignment issues:
* Add missing __packed attributes + padding across all drivers; in
most places there was an assumption that padding will be always
minimally suitable; in few places - e.g., in urtw(4) / rtwn(4) -
padding was just missing.
* Add __aligned(8) attribute for all Rx radiotap headers since they can
contain 64-bit TSF timestamp; it cannot appear in Tx radiotap headers, so
just drop the attribute here. Refresh ieee80211_radiotap(9) man page
accordingly.
- Since net80211 automatically updates channel frequency / flags in
ieee80211_radiotap_chan_change() drop duplicate setup for these fields
in drivers.
Tested with Netgear WG111 v3 (urtw(4)), STA mode.
MFC after: 2 weeks
Wrap ieee80211_add_channel_list_2ghz into another function
which supplies default (1-14) channel list to it and drop
its copies from drivers.
Checked with RTL8188EE, country US / JP / KR / UA.
MFC after: 2 weeks
This fixes 32-bit compat (no ioctl command defintions are required
as struct ifreq is the same size). This is believed to be sufficent to
fully support ifconfig on 32-bit systems.
Reviewed by: kib
Obtained from: CheriBSD
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14900
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Focus on code where we are doing multiplications within malloc(9). None of
these is likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
This removes the direct WME info access in the ieee80211com struct and instead
provides a method of fetching the data. Right now it's a no-op but eventually
it'll turn into a per-VAP method for drivers that support it (eg iwn, iwm,
upcoming ath10k work) as things like p2p support require this kind of behaviour.
Tested:
* ath(4), STA and AP mode
TODO:
* yes, this is slightly stack size-y, but it is an important first step
to get drivers migrated over to a sensible WME API. A lot of per-phy things
need to be converted to per-VAP before P2P, 11ac firmware, etc stuff shows up.
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
similar to "if (ticks > localvar+interval) {localvar=ticks; ...}" where
localvar is initialized to zero. Ticks is initialized to a negative value
since r278230, and that leads to these if statements never being true.
Return full channel list via iwi_getradiocaps() method
(ieee80211_init_channels() was replaced with iwi_getradiocaps()
to be consistent with other drivers).
PR: 216923
Submitted and tested by: ds@ukrhub.net (original patch)
MFC after: 5 days
Since r288350, ic_wme_task() is called via ieee80211_runtask(),
so, any additional deferring from the driver side is not needed.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4072
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
This fatal mismatch appeared to be absolutely harmless, since both structs
have pointer to struct ifnet as their first member, and they both point to
the same ifnet. And the first member is the only one used from the argument.
The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
appropriate state handling takes place, not doing so results in the
device doing nothing until manual intervention.
Reviewed by: iwasaki
Tested by: iwasaki (iwi)
MFC after: 4 weeks
After 8.0-RELEASE, iwi(4) doesn't send any data frames in infrastructure
mode.
Bacause of the condition `while (frm < efrm)', IEEE80211_VERIFY_LENGTH()
was checking item length beyond the ieee80211_frame region, and returned
from iwi_checkforqos() without setting flags, capinfo and associd.
In infrastructure mode associd is required, so this problem causes
discarding mbuf in ieee80211_start().
PR: kern/165819
Tested/Reviewed/Supported by: bschmidt and adrian
MFC after: 1 week
The version is used to check if a module is already preset, not setting
it results in:
can't re-use a leaf (ipw)!
module_register: module pci/ipw already exists!
Module pci/ipw failed to register: 17
while trying to load the module due to an entry in loader.conf. With this
commit we get the expected:
module ipw already present!
Reported by: Dru Lavigne, bz
Tested by: bz
MFC after: 1 week
the association notification), the included information though always
contains an elem block with an odd number of bytes. We handle the last
byte as if it might contain a whole elem block, this of course is not
true as one byte is not enough to hold a block, we therefore discard the
complete frame. The solution here is to subtract one from the actual
notification length, this is also what the Linux driver does. With this
change the frames ends exactly where the last elem block ends.
This commit also reverts r214160 which is no longer required and now even
wrong.
MFC after: 1 week