- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
takes care of all the 10/100 and gigE PCI drivers that I've done.
Next will be the wireless drivers, then the USB ones. I may pick up
some stragglers along the way. I'm sort of playing this by ear: if
anyone spots any places where I've screwed up horribly, please let me
know.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
close PR #13757, however I'm waiting on user feedback before declaring the
PR officially closed. Among other things, this improves UDP transmit
performance, and tx underruns are now detected and the TX start threshold
adjusted accordingly.
had to get the ML 6692 PHY driver working correctly, which is harder than
it sounds. "Bitrate" ThunderLAN devices should still be supported (i.e
the older 10Mbps Netflex 3/P, which use the TNETE110 chip that has no
MII support). The ThunderLAN has an internal PHY which makes things a
little complicated, but these are the basic rules:
- For devices with just the ThunderLAN, the internal PHY is used to
provide 10baseT, and 10base5/10baseT support. Autonegotiation will
work, but only with 10baseT links. The only thing that really gets
negotiated is whether the link is full or half duplex.
- For devices with the ThunderLAN and an external 10/100 PHY (like the
Compaq Netelligent 100Mbps cards, or the internal Netflex 3/P with
100Mbps upgrade daughter card), the external PHY is used for 10baseT
and 100baseTX modes. The internal PHY is still used to support
10base5/10base2, though you have to select them manual with ifconfig.
- For devices with the ThunderLAN and the ML6692 PHY, both the internal
and external PHYs are used, though it will appear as though the 6692
PHY will be used to support 10baseT and 100baseTX modes. In reality,
the internal PHY will be used for 10baseT, but this fact will be hidden
from the user. The 10base5/10base2 modes can also be selected manually
as with above.
been booted works too -- very neat. However I don't want the system to
stop for 5 seconds when the MII autoprobe is triggered in the xl and
tl drivers since that's lame. Instead, only use the hard delay when
we've been cold booted. If not, use the timeout mechanism instead.
(The SysKonnect driver doesn't use the same autonegotiation scheme, so
no change is required there.)
compiles cleanly on the Alpha. (On the alpha, the port type is an int,
not a short).
Cast a couple of pointers to ints via 'uintptr_t' rather than 'unsigned
int' since uintptr_t is long (64 bit) on Alpha, as are pointers.
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
- Change to the same transmit scheme as the PNIC driver.
- Dynamically set the cache alignment, and set burst size the same as
the PNIC driver in mx_init().
- Enable 'store and forward' mode by default. This is the slowest option
and it does reduce 100Mbps performance somewhat, but it's the most
reliable setting I can find. I'm more interested in having the driver
work reliably than trying to squeeze the best performance out of it.
The reason I'm doing this is that on *some* systems you may see a lot
of transmit underruns (which I can't explain: these are *fast* test
systems) and these errors seem to cause unusual and decidedly
non-tulip-like behavior. In normal 10Mbps mode, performance is fine
(you can easily saturate a 10Mbps link).
Also tweak some of the other drivers:
- Increase the size of the TX ring for the Winbond, ASIX, VIA Rhine
and PNIC drivers.
- Set a larger value for ifq_maxlen in the ThunderLAN driver. The setting
of TL_TX_LIST_CNT - 1 is too low (the ThunderLAN driver only allocates
20 transmit descriptors, and I don't want to fiddle with that now
because the ThunderLAN's descriptor structure is an oddball size
compared to the others).
the alpha. Now the ThunderLAN driver works on the alpha (both my
sample cards check out.) Update the alpha GENERIC config to include
ThunderLAN driver now that I've tested it.
- When trying to map ports, if mapping TL_PCI_LOIO or TL_PCI_LOMEM fails,
try mapping the other one. Apparently, some ThunderLAN parts swap these
two registers while others don't.
- Add support for bitrate (non-MII) PHYs. If no MII-based PHY is found,
program the chip for bitrate mode. This is required for the TNETE110
part, which doesn't have MII support. (It's also obsolete, but there
are still some people out there who have them.) With this change and the
change above, the Compaq Netflex-3/P 10baseT/BNC board works correctly.
(Thanks to Matthew Dodd for getting me one of these cards.)
- Convert to bus_space_foo() for register accesses.
- Add changes to support FreeBSD/Alpha. I still have to actually test
this in my Alpha box so I'm not going to update /sys/alpha/conf/GENERIC
yet.
address, account for cards which report the Texas Instruments PCI vendor ID
in addition to Compaq and Olicom. (I don't actually have a card that
reports the TI vendor/device ID, but it appears that some Racore adapters
work this way, and failing to account for it when we have the ID listed
in the supported devices list is a bug.)
apparently possible) event that the transmit start routine is
called with and empty if_snd queue, bail out instead of dereferencing
unilitialized transmit list pointers and panicking.
and increase the tx interrupt threshold to 4. This fixes performance
problems on slower systems.
Also fix a mind-o in the rx ring init routine: I used the TX
constant instead of the RX. This isn't a problem as long as the
rings are the same size, but if they aren't hijinx will ensue.
memory mapped mode. There are some laptop docking stations with
built-in tlan chips where memory mapped mode doesn't work correctly.
Pointed out by: jmb
PHYs in tl_attach(). This is mainly to suck away any possible stray
interrupts.
This prevents an intermittent problem on some systems where the adapter
probes correctly but yields a device timeout (and possible subsequent adapter
check) when configured. When I originally tested the driver, I ifconfig'ed
the interface after the system had already been booted and didn't notice
any problems, but when configuring the interface immediately at startup,
it would occasionally timeout and hang, until an adapter check interrupt
came along and reset things again. I'm not exactly sure if this is a
general problem of just something peculiar to this hardware (there are
three devices, including the tlan, all on IRQ 11) but the extra reset
shouldn't hurt anything. (It works fine with my 100Mbps Olicom adapter too.)
Thanks to Mark Taylor from Cybernet (mtaylor@cybernet.com) for allowing
me remote access to a Compaq system for debugging purposes.
