processors unless the invariant TSC bit of CPUID is set. Intel processors
may stop incrementing TSC when DPSLP# pin is asserted, according to Intel
processor manuals, i. e., TSC timecounter is useless if the processor can
enter deep sleep state (C3/C4). This problem was accidentally uncovered by
r222869, which increased timecounter quality of P-state invariant TSC, e.g.,
for Core2 Duo T5870 (Family 6, Model f) and Atom N270 (Family 6, Model 1c).
Reported by: Fabian Keil (freebsd-listen at fabiankeil dot de)
Ian FREISLICH (ianf at clue dot co dot za)
Tested by: Fabian Keil (freebsd-listen at fabiankeil dot de)
- Core2 Duo T5870 (C3 state available/enabled)
jkim - Xeon X5150 (C3 state unavailable)
resource allocation from an x86 Host-PCI bridge driver so that it can be
reused by the ACPI Host-PCI bridge driver (and eventually the MPTable
Host-PCI bridge driver) instead of duplicating the same logic. Note that
this means that hw.acpi.host_mem_start is now replaced with the
hw.pci.host_mem_start tunable that was already used in the non-ACPI case.
This also removes hw.acpi.host_mem_start on ia64 where it was not
applicable (the implementation was very x86-specific).
While here, adjust the logic to apply the new start address on any
"wildcard" allocation even if that allocation comes from a subset of
the allowable address range.
Reviewed by: imp (1)
register both status change and link state change callbacks.
Implement checking valid link in state change callback and poll
active link state in vr_tick(). This allows immediate detection of
lost link as well as protecting driver from frequent link flips during
link renegotiation. taskq implementation was removed because driver
now needs to poll link state in vr_tick().
While I'm here do not report current link state if interface is not
running.
Tested by: n_hibma
MFC after: 1 week
o Consider No CIS a normal event and stop whining about it so much
(too many cards are like this, espeically usb/firewire cards).
o Add comments to the cis reading code.
o Made the read from config space a smidge easier to read and eliminate
a loop that can be done mathematically.
present. Only call the bus to check if we actually do timeout so we
don't affect the normal case (since this case needn't be optimized and
this guards against all races).
child is still present. If not, return 'handled' and don't print
anything (this is expected behavior). We expect an interrupt on eject,
power-down and/or shutdown.
particular flow control and dma coalesce. Also improve the
sysctl operation on those too.
Add IPv6 detection in the ioctl code, this was done for
ixgbe first, carrying that over.
Add resource ability to disable particular adapter.
Add HW TSO capability so vlans can make use of TSO
proceeding.
On boot, some laptops with certain cards in them sometimes fail on
boot, but if the card is inserted after boot it works. Experiments
show that small delays here makes things more reliable. It is
believed that some combinations need a little more time before the
power on the card is really stable enough to be reliable once the
power is stable in the bridge.
ACPI Device() objects that do not have any device IDs available via the
_HID or _CID methods. Without a device ID a device driver cannot attach
to the device anyway. Namespace objects that are devices but not of
type ACPI_TYPE_DEVICE are not affected.
A few BIOSes have also attached a _CRS method to a PCI device to
allocate resources that are not managed via a BAR. With the previous
code those resources are allocated from acpi0 directly which can interfere
with the new PCI-PCI bridge driver (since the PCI device in question may
be behind a bridge and its resources should be allocated from that
bridge's windows instead). The resources were also orphaned and
and would end up associated with some other random device whose device_t
reused the pointer of the original ACPI-enumerated device (after it was
free'd by the ACPI PCI bus driver) in devinfo output which was confusing.
If we want to handle _CRS on PCI devices we can adjust the ACPI PCI bus
driver to do that in the future and associate the resources with the
proper device object respecting PCI-PCI bridges, etc.
Note that with this change the ACPI PCI bus driver no longer has to
delete ACPI-enumerated device_t devices that mirror PCI devices since
they should in general not exist. There are rare cases when a BIOS
will give a PCI device a _HID (e.g. I've seen a PCI-ISA bridge given
a _HID for a system resource device). In that case we leave both the
ACPI and PCI-enumerated device_t objects around just as in the previous
code.
method instead of reusing the existing per-queue interrupt task.
Reusing the per-queue interrupt task could result in both an interrupt
thread and the taskqueue thread trying to handle received packets on a
single queue resulting in out-of-order packet processing.
- Don't define igb_start() at all on 8.0 and where if_transmit is used.
Replace last remaining call to igb_start() with a loop to kick off
transmit on each queue instead.
- Call ether_ifdetach() earlier in igb_detach().
- Drain tasks and free taskqueues during igb_detach().
Reviewed by: jfv
MFC after: 1 week
announced during boot and contains the port number. The pnpinfo string
lists the port type (PUC_TYPE_* constants).
Tested by: Boris Samorodov bsam ipt ru
MFC after: 1 week
sys/dev/xen/blkback/blkback.c:
o Implement front-end request coalescing. This greatly improves the
performance of front-end clients that are unaware of the dynamic
request-size/number of requests negotiation available in the
FreeBSD backend driver. This required a large restructuring
in how this driver records in-flight transactions and how those
transactions are mapped into kernel KVA. For example, the driver
now includes a mini "KVA manager" that allocates ranges of
contiguous KVA to patches of requests that are physically
contiguous in the backing store so that a single bio or UIO
segment can be used to represent the I/O.
o Refuse to open any backend files or devices if the system
has yet to mount root. This avoids a panic.
o Properly handle "onlined" devices. An "onlined" backend
device stays attached to its backing store across front-end
disconnections. This feature is intended to reduce latency
when a front-end does a hand-off to another driver (e.g.
PV aware bootloader to OS kernel) or during a VM reboot.
o Harden the driver against a pathological/buggy front-end
by carefully vetting front-end XenStore data such as the
front-end state.
o Add sysctls that report the negotiated number of
segments per-request and the number of requests that
can be concurrently in flight.
Submitted by: kdm
Reviewed by: gibbs
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
of the devices we manage. These changes can be due to writes
we make ourselves or due to changes made by the control domain.
The goal of these changes is to insure that all state transitions
can be detected regardless of their source and to allow common
device policies (e.g. "onlined" backend devices) to be centralized
in the XenBus bus code.
sys/xen/xenbus/xenbusvar.h:
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbus_if.m:
Add a new method for XenBus drivers "localend_changed".
This method is invoked whenever a write is detected to
a device's XenBus tree. The default implementation of
this method is a no-op.
sys/xen/xenbus/xenbus_if.m:
sys/dev/xen/netfront/netfront.c:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkback/blkback.c:
Change the signature of the "otherend_changed" method.
This notification cannot fail, so it should return void.
sys/xen/xenbus/xenbusb_back.c:
Add "online" device handling to the XenBus Back Bus
support code. An online backend device remains active
after a front-end detaches as a reconnect is expected
to occur in the near future.
sys/xen/interface/io/xenbus.h:
Add comment block further explaining the meaning and
driver responsibilities associated with the XenBus
Closed state.
sys/xen/xenbus/xenbusb.c:
sys/xen/xenbus/xenbusb.h:
sys/xen/xenbus/xenbusb_back.c:
sys/xen/xenbus/xenbusb_front.c:
sys/xen/xenbus/xenbusb_if.m:
o Register a XenStore watch against the local XenBus tree
for all devices.
o Cache the string length of the path to our local tree.
o Allow the xenbus front and back drivers to hook/filter both
local and otherend watch processing.
o Update the device ivar version of "state" when we detect
a XenStore update of that node.
sys/dev/xen/control/control.c:
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbusb.c:
sys/xen/xenbus/xenbusb.h:
sys/xen/xenbus/xenbusvar.h:
sys/xen/xenstore/xenstorevar.h:
Allow clients of the XenStore watch mechanism to attach
a single uintptr_t worth of client data to the watch.
This removes the need to carefully place client watch
data within enclosing objects so that a cast or offsetof
calculation can be used to convert from watch to enclosing
object.
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
- Fix races on setting AAC_AIFFLAGS_ALLOCFIBS
- Remove some unused AAC_IFFLAGS_* bits.
Please note that the kthread still makes a difference between the
total mask and AAC_AIFFLAGS_ALLOCFIBS because more flags may be
added in the future to aifflags.
Sponsored by: Sandvine Incorporated
Reported and reviewed by: emaste
MFC after: 2 weeks
but has only 2 SATA ports instead of 4. The worst part is that SStatus and
SError registers for missing ports are not implemented and return wrong
values (0xffffffff), that caused infinite reset loop.
Just ignore that SError value while I found no better way to identify them.
increase robustness (no more calls to panic(9)) and simplify
code.
- Allocate RX/TX data structures as a single buffer rather than
an array of 4KB pages to simplify code.
- Fixed LRO (aka TPA) code. Removed kernel module parameter and
support enabling disabling LRO through ifconfig(8) command line.
LRO is still disabled by default but should be enabled for best
performance on an endpoint device.
- Fixed statistcs code and removed kernel module parameter (stats
should just work).
- Added many software counters to help identify the cause of some
performance issues.
- Streamlined adapter internal init/stop code paths.
- Fiddled with debug code (adding some here, removing some there).
- Continued style(9) adjustments.
- Add retry loops in the i2c read/write functions.
- Combied the ADC channel selection and readout of the value into
one iicbus_transfer to avoid possible races.
Reviewed by: nwhitehorn
of just setting it to the first registered device, reevaluate it for each
device registered, trying to choose best candidate, unless one was forced.
For now use such preference order: play&rec, play, rec.
As side effect, this should workaround the situation when HDMI audio output
of the video card, usually not connected to anything, becomes default, that
requires manual user intervention to make sound working. If at some point
this won't be enough, we can try to fetch some additional priority flags
from the device driver.
For the AR5211/AR5212, this is apparently a one byte pulse duration
counter value. It is only coded up here for the AR5212 as I don't have
any AR5211-series hardware to test it on.
This information was extracted from the Madwifi DFS branch along with
some local additions.
Please note - all this does is extract out the radar event duration,
it in no way reflects the presence of a radar. Further code is needed
to take a set of radar events and filter them to extract out correct
radar pulse trains (and ignore other events.)
For further information, please see:
http://wiki.freebsd.org/dev/ath_hal%284%29/RadarDetection
This includes references to the relevant patents which describe what
is going on.
Obtained from: Madwifi
Many thanks to Tino <tinotom@gmail.com> for drawing my attention to
this, for doing a lot of testing and providing great feedback.
Many thanks to AMD for continuing to release public specifications for
their chipsets.
PR: kern/157568
Tested by: Tino <tinotom@gmail.com>
MFC after: 1 week
points are fixed addresses and (U)EFI CSM specification also mandated that.
Unfortunately, (U)EFI CSM specification does not specifically mention this
is to call service routine via interrupt vector table or to jump directly
to the entry point. As a result, some CSM seems to install two routines
and acts differently, depending on how it was executed, unfortunately.
When INT 15h is used, it calls a function pointer (which is probably a UEFI
service function). When it jumps directly to the entry point, it executes
a simple and traditional INT 15h service routine. Therefore, actually there
are two possible fixes, i. e., this fix or jumping directly to the fixed
entry point. However, we chose this fix because a) keyboard typematic
support via BIOS is becoming extremely rarer and b) we cannot support random
service routine installed by a firmware or a boot loader. This should fix
Lenovo X220 laptop, specifically.
Reviewed by: delphij
MFC after: 3 days
High-speed USB HUB by resetting the transaction translator (TT)
before trying re-enumeration. Also when clear-stall fails multiple times
try a re-enumeration.
Suggested by: Trevor Blackwell
MFC after: 14 days
