This extends vdev_id to support a new slot type, ses, for SCSI Enclosure
Services. With slot type ses, the disk slot numbers are determined by
using the device slot number reported by sg_ses for the device with
matching SAS address, found by querying all available enclosures.
This is primarily of use on systems with a deficient driver omitting
support for bay_identifier in /sys/devices. In my testing, I found that
the existing slot types of port and id were not stable across disk
replacement, so an alternative was required.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Simon Guest <simon.guest@tesujimath.org>
Closes#6956
With HPE hardware and hpsa-driven SAS adapters, only a single phy is
reported, but no individual per-port phys (ie. no phy* entry below
port_dir), which breaks topology detection in the current sas_handler
code. Instead, slot information can be derived directly from the port
number. This change implements a new slot keyword "port" similar to
"id" and "lun", and assumes a default phy/port of 0 if no individual
phy entry can be found. It allows to use the "sas_direct" topology with
current HPE Dxxxx and Apollo 45xx JBODs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6484
Add new keyword 'slot' to vdev_id.conf
This selects from where to get the slot number for a SAS/SATA disk
Needed to enable access to the physical position of a disk in a
Supermicro 2027R-AR24NV .
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#3693
The vdev_id udev helper currently applies slot renumbering rules to
every channel (JBOD) in the system. This is too inflexible for systems
with non-homogeneous storage topologies. The "slot" keyword now takes
an optional third parameter which names a channel to which the mapping
will apply. If the third parameter is omitted then the rule applies to
all channels. The first-specified rule that can match a slot takes
precedence. Therefore a channel-specific rule for a given slot should
generally appear before a generic rule for the same slot number. In
this way a custom slot mapping can be applied to a particular channel
and a default mapping applied to the rest.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2056
Add a vdev_id feature to map device names based on already defined
udev device links. To increase the odds that vdev_id will run after
the rules it depends on, increase the vdev.rules rule number from 60
to 69. With this change, vdev_id now provides functionality analogous
to zpool_id and zpool_layout, paving the way to retire those tools.
A defined alias takes precedence over a topology-derived name, but the
two naming methods can otherwise coexist. For example, one might name
drives in a JBOD with the sas_direct topology while naming an internal
L2ARC device with an alias.
For example, the following lines in vdev_id.conf will result in the
creation of links /dev/disk/by-vdev/{d1,d2}, each pointing to the same
target as the device link specified in the third field.
# by-vdev
# name fully qualified or base name of device link
alias d1 /dev/disk/by-id/wwn-0x5000c5002de3b9ca
alias d2 wwn-0x5000c5002def789e
Also perform some minor vdev_id cleanup, such as removal of the unused
-s command line option.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#981
vdev_id parses the file /etc/zfs/vdev_id.conf to map a physical path
in a storage topology to a channel name. The channel name is combined
with a disk enclosure slot number to create an alias that reflects the
physical location of the drive. This is particularly helpful when it
comes to tasks like replacing failed drives. Slot numbers may also be
re-mapped in case the default numbering is unsatisfactory. The drive
aliases will be created as symbolic links in /dev/disk/by-vdev.
The only currently supported topologies are sas_direct and sas_switch:
o sas_direct - a channel is uniquely identified by a PCI slot and a
HBA port
o sas_switch - a channel is uniquely identified by a SAS switch port
A multipath mode is supported in which dm-mpath devices are handled by
examining the first running component disk, as reported by 'multipath
-l'. In multipath mode the configuration file should contain a
channel definition with the same name for each path to a given
enclosure.
vdev_id can replace the existing zpool_id script on systems where the
storage topology conforms to sas_direct or sas_switch. The script
could be extended to support other topologies as well. The advantage
of vdev_id is that it is driven by a single static input file that can
be shared across multiple nodes having a common storage toplogy.
zpool_id, on the other hand, requires a unique /etc/zfs/zdev.conf per
node and a separate slot-mapping file. However, zpool_id provides the
flexibility of using any device names that show up in
/dev/disk/by-path, so it may still be needed on some systems.
vdev_id's functionality subsumes that of the sas_switch_id script, and
it is unlikely that anyone is using it, so sas_switch_id is removed.
Finally, /dev/disk/by-vdev is added to the list of directories that
'zpool import' will scan.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#713
