I586_OPTIMIZED_BCOPY is configured.
Similarly for bzero/I586_OPTIMIZED_BZERO.
Fake 586's had better have a hardware FPU with non-broken exception
handling (we mask exceptions, but broken exception handling may trap
on the instructions that do the masking). I guess this means that
the routines won't work on most 386's or FPUless 486's even when they
have a h/w FPU.
These are based on using the FPU to do 64-bit stores. They also
use i586-optimized instruction ordering, i586-optimized cache
management and a couple of other tricks. They should work on any
i*86 with a h/w FPU, but are slower on at least i386's and i486's.
They come close to saturating the memory bus on i586's. bzero()
can maintain a 3-3-3-3 burst cycle to 66 MHz non-EDO main memory
on a P133 (but is too slow to keep up with a 2-2-2-2 burst cycle
for EDO - someone with EDO should fix this). bcopy() is several
cycles short of keeping up with a 3-3-3-3 cycle for writing. For
a P133 writing to 66 MHz main memory, it just manages an N-3-3-3,
3-3-3-3 pair of burst cycles, where N is typically 6.
The new routines are not used by default. They are always configured
and can be enabled at runtime using a debugger or an lkm to change
their function pointer, or at compile time using new options (see
another log message).
Removed old, dead i586_bzero() and i686_bzero(). Read-before-write is
usually bad for i586's. It doubles the memory traffic unless the data
is already cached, and data is (or should be) very rarely cached for
large bzero()s (the system should prefer uncached pages for cleaning),
and the amount of data handled by small bzero()s is relatively small
in the kernel.
Improved comments about overlapping copies.
Removed unused #include.
I have only tested the ABP5140 card and only with a single CDROM drive
but it seems to work fine. This driver relies on features found only in
the SCSI branch so will not work in -current until those changes
are brought in. It also doesn't have any error handling code *yet*.
The goal is to use this driver as the development platform for the new
generic SCSI layer error recovery/handling code.
PCI and EISA front ends will show up as soon as I get my hands on
the cards. There are also a few issues in the driver that I need
to clear up with AdvanSys before I can suggest sticking one of
these cards in your server. 8-)
Thanks to AdvanSys for releasing this code under a suitable copyright.
Obtained from: Ported from the Linux driver writen by
bobf@advansys.com (Bob Frey).
[long long] results when I last worked on them, but they are normally
used together with to daddr_t's and off_t's which are signed, so the
unsigned results did little except cause warnings.
The main change is from unsigned long unsigned int. It just needs to
be a 32-bit type and unsigned int is most natural. Using a non-long
type has the "advantage" of hiding bugs in the "machine-independent"
code where it prints foo_t's using %d or %x. These bugs are currently
hidden bug not compiling with -Wformat.
I tried changing vm_ooffset_t from long long to unsigned long long, but
that was wrong because vm_ooffset_t needs to be long to match off_t,
although file offsets are never negative.
Reviewed by: dyson
Staticized it in userconfig. The one in pcvt is unused.
Removed bogus unused arg to getchar(). This should not have compiled
in the USERCONFIG_BOOT case, but the getchar() was also non-prototyped
and defined in K&R style.
Staticized the badly named global variable `next'. Even static variables
should have a unique module-specific prefix so that they can be referenced
easily in debuggers, etc.
First, change sysinstall and the Makefile rules to not build the kernel
nlist directly into sysinstall now. Instead, spit it out as an ascii
file in /stand and parse it from sysinstall later. This solves the chicken-n-
egg problem of building sysinstall into the fsimage before BOOTMFS is built
and can have its symbols extracted. Now we generate the symbol file in
release.8.
Second, add Poul-Henning's USERCONFIG_BOOT changes. These have two
effects:
1. Userconfig is always entered, rather than only after a -c
(don't scream yet, it's not as bad as it sounds).
2. Userconfig reads a message string which can optionally be
written just past the boot blocks. This string "preloads"
the userconfig input buffer and is parsed as user input.
If the first command is not "USERCONFIG", userconfig will
treat this as an implied "quit" (which is why you don't need
to scream - you never even know you went through userconfig
and back out again if you don't specifically ask for it),
otherwise it will read and execute the following commands
until a "quit" is seen or the end is reached, in which case
the normal userconfig command prompt will then be presented.
How to create your own startup sequences, using any boot.flp image
from the next snap forward (not yet, but soon):
% dd of=/dev/rfd0 seek=1 bs=512 count=1 conv=sync <<WAKKA_WAKKA_DOO
USERCONFIG
irq ed0 10
iomem ed0 0xcc000
disable ed1
quit
WAKKA_WAKKA_DOO
Third, add an intro screen to UserConfig so that users aren't just thrown
into this strange screen if userconfig is auto-launched. The default
boot.flp startup sequence is now, in fact, this:
USERCONFIG
intro
visual
(Since visual never returns, we don't need a following "quit").
Submitted-By: phk & jkh
divisor latch registers if the registers wouldn't change.
Use the default console cfcr setting while setting the divisor
latch registers for console i/o. Input may be messed up by
transiently changing the cfcr.
Use a usual cfcr setting while setting the divisor latch registers
in the probe. This shouldn't matter, but this is not the place to
test the UART's handling of 5 bit words.
Removed a stale devfs comment.
was always disabled because "pci.h" wasn't included. Now the configured
pci devices are listed and you can edit bogus flags for them.
Fixed bitrot in the disabled code. A used #include was removed and const
poisoning wasn't fixed.
Removed unused #include.
dependent operation, and not really a correct name. invltlb and invlpg
are more descriptive, and in the case of invlpg, a real opcode.
Additionally, fix the tlb management code for 386 machines.
for headers in the compile directory work unsurprisingly. Without
-I-, the search for "foo.h" begins in the directory of the file
that includes it, and the compile directory is only searched because
`-I.' is in ${INCLUDES}.
Removed -I$S/sys from ${INCLUDES}. It was once necessary to find
things like "param.h" in $S/sys. Now <sys/param.h> is found in $S.
lcall 7,0 (ie: ldt slot 0) and lcall 0x87,0 (ldt slot 16, it's shifted
three bits to the left). I was fiddling with this so long ago, I don't
recall the specifics.
with this quite a while ago when somebody reported a BSD/OS 2.1 binary
that wouldn't run. I'm pretty sure they tried it and I'm pretty sure
they mentioned to me that the patch worked.
