r211130 in favor of this more general fix.
This fixes a compilation error for mips 64-bit little endian build.
libexec/rtld-elf/mips/reloc.c:196: warning: right shift count >= width of type
Suggested by: stefanf, jchandra, bde
bridge(4), lagg(4) etc. and make use of function pointers and
pf_proto_register() to hook carp into the network stack.
Currently, because of the uncertainty about whether the unload path is free
of race condition panics, unloads are disallowed by default. Compiling with
CARPMOD_CAN_UNLOAD in CFLAGS removes this anti foot shooting measure.
This commit requires IP6PROTOSPACER, introduced in r211115.
Reviewed by: bz, simon
Approved by: ken (mentor)
MFC after: 2 weeks
list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
While there, also fix some places assuming cpu type is 'int' while
u_int is really meant.
Note: this will also fix some possible races in per-cpu data accessings
to be addressed in further commits.
In collabouration with: Yahoo! Incorporated (via sbruno and peter)
Tested by: gianni
MFC after: 1 month
flag immediately so it's only set once per longcal interval.
Without this, the current AR5416 code will continuously spam NF
calibrations during a periodic calibration if the longcal flag
is set. The longcal flag wouldn't be cleared until the calibration
method indicates that calibrations are "complete".
This drops the rate of NF calibration updates down from "once every
shortcal" (ie, every 100ms) during a periodic calibration, to only
once per "longcal" interval. Spamming NF calibrations every 100ms
caused some potentially horrific issues in noisy environments as
NF calibrations can take longer than 100ms and this spamming can
cause invalid NF calibration results to be read back - leading to
missed beacons, and thus leading to a stuck beacon situation.
Stuck beacons cause interface resets, which restart calibrations.
This means that the longcal calibration runs every 100ms (shortcal)
until all initial calibrations are completed. This spamming can then
cause the above issues which leads to stuck beacons, leading to
interface resets, etc, etc. Quite annoying.
Now we use a regular mutex instead of a spin mutex. When we enter and exit
the emulator, spinlock_enter() and spinlock_exit() are additionally used.
Move some page table related stuff from x86bios_init() and x86bios_uninit()
to x86bios_map_mem() and x86bios_unmap_mem().
most system, based on benchmark results on a low-end fibre channel SAN
under VMWare:
vfs.read_max read performance
8 (historical default) 83 MB/s
16 (recent bump) 131 MB/s
32 (this version) 152 MB/s
64 157 MB/s
(results are +/- 3 MB/s)
As read-ahead is heuristic, based on past IO requests, it shouldn't be
problematic. The new default is still smaller then in other OSes.
Add proto spacers to inet6sw like we have for legacy IP. This allows us
to dynamically pf_proto_register() for INET6 from modules, needed by
upcoming CARP changes and SeND.
MC and SCTP could make use of it as well in theory in the future after
upcoming VIMAGE vnet teardown work.
Discussed with: will, anchie
MFC after: 10 days
Even though cons25 normally doesn't support origin regions, this
emulator does allow you to do it. It makes more sense to blank only the
origin region when emitting ^L instead of blanking the entire screen.
Apart from that, we should always place the cursor inside the origin
region, which doesn't happen right now.
within the device table. This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.
While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case. Change
uplcom(4) to do the same.
This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.
Reviewed by: hselasky
MFC after: 6 weeks
controller. These controllers are known as L1D(AR8151) and
L2CB/B2(AR8152). This change adds supports for the following
controllers.
o AR8151 v1.0(L1D) gigabit ethernet controller
o AR8151 v2.0(L1D) gigabit ethernet controller
o AR8152 v1.1(L2CB) fast ethernet controller
o AR8152 v2.0(L2CB2) fast ethernet controller
These controllers have the same feature of AR8131/AR8132 and
support improved power saving control. The user visible change at
this moment is reduced jumbo frame size from 9KB to 6KB. Many
thanks to Atheros for continuing to support FreeBSD.
HW donated by: Atheros Communications, Inc.
- Increase target limit from 4 to 64; this limit will be removed entirely
at a later time.
- Improve recovery from lost network connections.
- Fix some potential deadlocks and a serious memory leak.
- Fix incorrect use of MH_ALIGN (instead of M_ALIGN), which makes no
practical difference, but triggers a KASSERT with INVARIANTS.
- Fix some warnings in iscontrol(8) and improve the man page somewhat.
Submitted by: Daniel Braniss <danny@cs.huji.ac.il>
Sponsored by: Dansk Scanning A/S, Data Robotics Inc.
This fixes booting from a ZFS mirror with a unavailable primary device.
PR: kern/148655
Reviewed by: avg
Approved by: delphij (mentor)
MFC after: 3 days
like memory mapped register access. Typical problem from the issue
was MII access returned unreliable values. I'm not sure this comes
from lack of register flushing in MII access after accessing
STE_PHYCTL register though.
To address the issue, read hints data that controls which type of
memory mapping should be used in driver. ste(4) still prefers
memory mapping to io mapping but honor hints entered by user except
for controllers that have problems with memory mapping.
The hint to use iomapping could be given by adding the following
line to /boot/device.hints file.
hint.ste.0.prefer_iomap="1"
PR: kern/149285
MFC after: 5 days
number of CPUs detection.
However, that was not mention at all, the problem was not reported, the
patch has not been MFCed and the fix is mostly improper.
Fix the original overflow (caused when 32 CPUs must be detected) by
just using a different mathematical computation (it also makes more
explicit the size of operands involved, which is good in the moment
waiting for a more complete support for a large number of CPUs).
PR: kern/148698
Submitted by: Joe Landers <jlanders at vmware dot com>
Tested by: gianni
MFC after: 10 days
td_critnest > 1 when not already running on the desired CPU read the
TICK counter of the BSP via a direct cross trap request in that case
instead.
- Treat the STICK based timecounter the same way as the TICK based one
regarding its quality and obtaining the counter value from the BSP.
Like the TICK timers the STICK ones also are only synchronized during
their startup (which might not result in good synchronicity in the
first place) but not afterwards and might drift over time, causing
problems when the time is read from different CPUs (see r135972).
interface goes to issue LINK_UP, then LINK_DOWN, then LINK_UP at
cold boot. This behavior is not observed when carp(4) interface
is created slightly later, when the underlying interface is fully
up.
Before this change what happen at boot is roughly:
- ifconfig creates em0 interface;
- ifconfig clones a carp device using em0;
(em0's link state is DOWN at this point)
- carp state: INIT -> BACKUP [*]
- carp state: BACKUP -> MASTER
- [Some negotiate between em0 and switch]
- em0 kicks up link state change event
(em0's link state is now up DOWN at this point)
- do_link_state_change() -> carp_carpdev_state()
- carp state: MASTER -> INIT (via carp_set_state(sc, INIT)) [+]
- carp state: INIT -> BACKUP
- carp state: BACKUP -> MASTER
At the [*] stage, em0 did not received any broadcast message from other
node, and assume our node is the master, thus carp(4) sets the link
state to "UP" after becoming a master. At [+], the master status
is forcely set to "INIT", then an election is casted, after which our
node would actually become a master.
We believe that at the [*] stage, the master status should remain as
"INIT" since the underlying parent interface's link state is not up.
Obtained from: iXsystems, Inc.
Reported by: jpaetzel
MFC after: 2 months
suspend state. Also disable master clock after PHY power down,
this is supposed to save more power. The master clock should be
enabled if WOL is active.
to single CPUs more efficiently with Cheetah(-class) and Jalapeno CPUs.
Besides being used to implement the ipi_cpu() introduced in r210939,
cpu_ipi_single() will also be used internally by the sparc64 MD code.
- Factor out the Jalapeno support from the Cheetah IPI send functions
in order to be able to more easily and efficiently implement support
for more than 32 target CPUs as well as a workaround for Cheetah+
erratum 25 for the latter.
the vfs.read_max default. For most systems this means going from 128 KiB
to 256 KiB, which is still very conservative and lower than what most
other operating systems use, but as a sane default should not
interfere much with existing systems.
For systems with RAID volumes and/or virtualization envirnments, where
read performance is very important, increasing this sysctl tunable to 32
or even more will demonstratively yield additional performance benefits.
If MAXPHYS ever gets bumped up, it will probably be a good idea to slave
read_max to it.
SOCK_DGRAM socket. MSG_TRUNC was only returned when some mbufs could
not be copied to the application. If some data was left in the last
mbuf, it was correctly discarded, but MSG_TRUNC was not set.
Reviewed by: bz
MFC after: 3 weeks
