briefly over it, and see some serious architectural issues in this stuff.
On the other hand, I doubt that we will have any solution to these issues
before 2.1, so we might as well leave this in.
Most of the stuff is bracketed by #ifdef's so it shouldn't matter too much
in the normal case.
Reviewed by: phk
Submitted by: HOSOKAWA, Tatsumi <hosokawa@mt.cs.keio.ac.jp>
Slice 0 is now for the first BSD slice. The first BSD slice is
the first DOSpartition with id 0xa5 or the whole disk if their
are no DOSpartitions (except the latter is not yet implemented).
Existing partitions on it work the same as in 2.0 except the
'd' partition is no longer special and partitions are relative
to the skice.
Slice 1 is now for the whole disk and gets a read-only label
describing the disk. Previously, slice 0 was for the whole disk
and there was no label on it.
Slices 2-31 are for DOSpartitions. Slice 0 is an alias for one
of these if there is a BSD slice. Previously, slices 1-31 were
for DOSpartitions.
diskslice_machdep.c:
Expand whole disk slice to include all DOSpartitions. More work
is required for >1024 cylinders and to rewrite the label iff the
driver is unsure about the geometry.
subr_diskslice.c:
New function dsisopen() to help handle media changes.
mapping from numbers to names is messy for backwards compatibility.
E.g., for driver "sd", unit "0":
slice 0: omit the slice number for compatibility; names are sd0[a-h].
slice 1: omit the partition letter 'c' because the whole disk device
shouldn't have anything to do with partitions; sd0 is the
only name.
slices 2-31: subtract 1 from slice number to compensate for the
compatibility slice 0; names are sd0s[1-30][a-h].
when ttselect() is improved. This requires using an array of tty structs
and not using ttymalloc().
Fix an off by 1 error. Some caclulations seem to be off by a factor
of NCY. NCY defaults to 16, which gives 256 tty structs occupying
0xd000 bytes. The minor number encoding only allows 16 ttys.
Update the types of timeout functions to 2.0.
- Overflow now calculated right
- Close works ok,does not looses tty
- Better overflow handling now the snooping stops
on overflow,but programm notified and can reconnect if
it want to..Default maximal buffer set to 664 K and this
is probably too much..:)))
Utility still to come
Restore fixes to flushing that were lost in the previous commit.
Clean up snoop changes.
Add my TODO list from 1.1.5. The improvements in 1.1.5 should be "obtained"
first.
tape drive. I traced it to sys/scsi/scsi_base.c where some code were added
to print the return values of the sense command. My tape drive returned a
extended flags value of 0x20, so the key that is the lower 4 bits, is 0.
The code uses "key-1" to index into a table and then the kernel go to never-
never land.
Here is a fix for this. Will somebody please apply it?
Submitted by: John Hay
It boots FreeBSD from a running MS-DOS system.
It's compiled using some MS-DOS tools, but there is a binary
hidden in the uuencoded file. (Go ahead, flame me if you can come up
with a solution for the problem. Just saying "this is bad" doesn't count!)
Rod, you were right: one would have to deal with weird interfaces to the
memory managers, and it seems that Christian found them all, and made them
work.
Thanks Christian!
Reviewed by: phk
Submitted by: DI. Christian Gusenbauer <cg@fimp01.fim.uni-linz.ac.at>
Christians README:
------------------
Hi Everybody!
This is version 1.5 of "fbsdboot", a program that allows you to boot a kernel
from a MS-DOS partition or a FreeBSD partition. This program runs using DOS.
It works with various memory managers (like EMM386, 386MAX) under certain
circumstances.
First, a FreeBSD kernel is always loaded to memory starting at 0x100000. To
assure that loading the kernel *does not* overwrite memory used by memory
managers, high memory for the kernel is allocated and after loading the kernel
it's moved to 0x100000.
Second, there are many ways to switch to protected mode which is necessary to
start the kernel. Each BIOS gives you the possibility to use INT15H (AH=89H)
to do that. But some memory-managers like 386max does not allow you to use
this method.
An other way to do the switch is to use DPMI services, but they do not
guarantee, that the protected mode application is executed with privilege
level 0. Therefore this method is *not* used.
VCPI services offer another way to switch to protected mode, and VCPI servers
are built into "emm386.exe", "386max" and "qemm". That's why, this method is
implemented in fbsdboot.exe.
Fbsdboot.exe tries to switch to protected mode using VCPI services. If they're
not available INT15H is used to do the switch. If that fails, it's not possible
for this version of fbsdboot.exe to boot a kernel :-(.
You can get commandline options of fbsdboot if you start it with "-?" as option!
I don't know, if fbsdboot works with QEMM, as I don't have the possibility to
test it.
Enjoy and have fun!
Christian.
cg@fimp01.fim.uni-linz.ac.at
PS: Many thanks to Bruce Evans for his assistance!
Submitted by: Rich
Make conditionals on BIOSWAIT consistent with usage in io.c.
If you had 'BOOTWAIT=0' in your /etc/make.conf then biosboot wouldn't
compile. It was '#if' in io.c and '#ifdef' in probe_keyboard.c so I
changed the latter to '#if'.
Even if BOOTWAIT is undefined then '#if BOOTWAIT' becomes
'#if 0' so it should compile either way with this change.
