PCG-505BX (for example) has one of those:
wi0: <Intersil Prism3> mem 0xf8000000-0xf8000fff at device 2.0 on pci2
wi0: 802.11 address: 00:02:8a:94:d8:73
wi0: using RF:PRISM3(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.1), Station (1.5.6)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
has the same product id, but different vendor id. It also appears
that the MELCO's id should be 0x18a instead of 0x8a01. Fix this.
Submitted by: Shizuka Kudo-san
and up commands. When configuring the interface down only the
connections that are currently closing are deleted from the connection
table. When the interface is configured up, all connections that
are in the table are re-opened.
connections that have been open (and were not closing) when
the interface was stopped. This makes the behaviour of fatm(4) more like
the behaviour of en(4).
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
- Build SGL's for ATA_PASSTHROUGH commands
- Fallback to using the sgl_offset when the opcode is unknown for building
SGL's/
- Add ioctl calls for adding and removing units.
- Define previously undefined AEN's
- Allocate memory for the ioctl payload in multiples of 512bytes.
MFC after: 1 week
preparation for supporting the OPENVCC and CLOSEVCC ioctls which
are needed for ng_atm. This required some re-organisation of the code
(mostly converting array indexes to pointers). This also gives us
an array of open vccs that will help in using the generic GETVCCS handler.
the macro definition, and cause the generation of syntactically
incorrect code that gcc happens to accept.
Reviewed by: schweikh (mentor)
MFC after: 4 weeks
larger than normal frames, to account for the case where a bge(4) NIC
is used with VLANs. Since we set the IFCAP_VLAN_MTU flag, we must allow
reception of frames up to 1522 bytes in size rather than 1518.
Note that it is possible to work around this bug by doing:
# ifconfig bge0 mtu 1504
prior to configuring any VLAN interfaces.
recompiling the driver. See the comments near the top of "if_em.h"
for descriptions of these delays. Four new loader tunables control
the system-wide default values:
hw.em.tx_int_delay
hw.em.rx_int_delay
hw.em.tx_abs_int_delay
hw.em.rx_abs_int_delay
The tunables are specified in microseconds. The valid range is
0-67108 usec., and 0 means that the timer is disabled.
There are also four new sysctls (actually, a set of four for each
"em" device in the system) to query and change the interrupt delays
after the system is up:
hw.em0.tx_int_delay
hw.em0.rx_int_delay
hw.em0.tx_abs_int_delay (not present for 82542/3/4 adapters)
hw.em0.rx_abs_int_delay (not present for 82542/3/4 adapters)
It seems to be OK to change these values even while the adapter is
passing traffic.
Approved by: Prafulla Deuskar <pdeuskar@FreeBSD.ORG>
MFC after: 4 weeks
- Move isa/ppc* to sys/dev/ppc (repo-copy)
- Add an attachment method to ppc for puc
- In puc we need to walk the chain of parents.
Still to do, is to make ppc(4) & puc(4) work on other platforms. Testers
wanted.
PR: 38372 (in spirit done differently)
Verified by: Make universe (if I messed up a platform please fix)
This is controlled by a per-adapter sysctl hw.atm.hfaX.shape. When
set to 0, no shaping occures. When set to 1 at most 1 channel is
shaped. When set to 2 all CBR channels are shaped. Note, that the
latter may actually not work, because of the adapter supporting
the shaping of only one PDU at the same time.
also do it). Three problems have been encountered:
1. The initialisation command does not work in interrupt mode. Whether
this is a firmware bug or a feature is not clear. The original Fore
drivers execute the initialize command always in polling mode, so
it appears that this behaviour is expected. When we detect a 4.X.Y
firmware do busy wait on the command status.
2. The command code of the GET_PROM command has changed. This is an
unofficial command anyway. What was GET_PROM in 3.X.Y is CLEAR_STATS
in 4.X.Y (although unimplemented in the firmware). We need to
use the correct code depending on the firmware.
3. The 4.X.Y firmware can set the error flag in the command status
without also setting the completion flag (as the documenation says).
Check both variants.
An additional field in the per-card structure fu_ft4 is TRUE when we have
detected a 4.X.Y firmware. Otherwise it is false. The behaviour of the
driver when using a 3.X.Y firmware should be identical to the previous
behaviour.
This change will enable traffic shaping of (at least one) CBR channels.
allocation function. With this patch, it prevents continous growth of
the devbuf memory pool.
Tested with ssh <host> dd of=/dev/null < /dev/zero and vmstat -m | grep devbuf
receive 6 byte commands. Add a check for this flag to da(4) and cd(4) so
that they honor it. This is a quick workaround for many devices (especially
USB) that require da(4) quirks to operate. The more complete approach is
to finish the new transport code which will be aware of the SCSI version a
transport implements.
MFC after: 1 day
function unless the device is configured up. Without this fix, the
device ends up in the RUNNING state even though it is configured down.
Also, check the RUNNING flag before calling the if_start function, in
case the if_init function failed for one reason or another.
contain the filedescriptor number on opens from userland.
The index is used rather than a "struct file *" since it conveys a bit
more information, which may be useful to in particular fdescfs and /dev/fd/*
For now pass -1 all over the place.
newer lucent/hermes firmware than indicated (investigating). I'm committing
this now since it shouldn't hurt anything.
o Vaguely related, add bogus frame length check from netbsd.
Obtained from: netbsd
it attaches to all existing NATM network interfaces in the system
and creates a HARP physical interface for each of them. This allows
us to use the same set of ATM drivers for all ATM stuff. It is
possible to use the same interface for HARP, NATM and netgraph at the
same time.
go looking for free fragments won't match. Since we never free this, we
can "throw away" the tag. This is very dirty, and needs to be reimplemented
properly, but fixes performance problems with uhci.
Also assert that when we overlay a structure on some space, that the
space is large enough for the structure.
namespace. To compensate for it only being used in the !ECDT case, use
a more robust approach to indicate a device was probed via ECDT by setting
the private ivar to be &acpi_ec_devclass. Without the acpi_MatchHid() call
now, it might have been possible for a non-EC device to have had its magic
match our previous flag.
Pointed out by: takawata
to EcGpeQueryHandler on to any waiting threads through the softc. Similar
behavior was in the original version.
Also:
* Merge EcQuery into EcGpeQueryHandler to simplify locking
* Hold EcLock from the initial read of the CSR down to the wakeup or
until after the query command has been processed.
* ec_gpebit only needs to be a UINT8
namespace has been evaluated. Machines with ACPI 2.0 expect this behavior
and have AML which calls EC functions early in the boot process. If the
ECDT is not available, fall back to original probe behavior.
Other minor changes:
* Add GPE bit and GLK usage to the device announcement
* Always use the global lock in the ECDT case, but potentially downgrade to
not using it if _GLK is 0 once the namespace is available. This is
announced with "Changing GLK from 1 to 0"
* Remove the acpi_object_list definitions which were earlier deprecated
Ideas from: takawata
- 5705 doesn't support jumbo frames
- Statistics must be read from registers
- RX return ring must be capped at 512 entries
- Omit initialization of certain device blocks
- Acknowledge link change interrupts by setting the 'link changed'
bit in the status register (used to have no effect)
- Remember to toggle the MI completion bit too
- Set the mbuf low watermark differently (on-chip memory buffers,
not BSD mbufs)
- Don't enable Ethernet@WireSpeed feature for certain 5705 chip revs
- Add additional PCI IDs for 5705 and 5782 parts
- Add a forgotten 5704 PCI ID
Most changes ripped kicking and screaming from the Broadcom linux driver.
Thanks to Paul Saab for sanity testing. (My lack of sanity has been
confirmed.)
sync of the NetBSD code.
fix isochornous support for ohci. This gets webcams like my OV511
working on sparc64.
PR: kern/52589
Submitted by: Bruce R. Montague (isochonous support)
Reviewed by: joe among others
callback will never be deferred. ATM needs to prevent cell and packet
ordering. Also use the default mutex and lock functions (those that
panic) for the tag creation.
with a ProATM-155 and an IDT evaluation board and should also work
with a ProATM-25 (it seems to work at least, I cannot really measure
what the card emits). The driver has been tested on i386 and sparc64,
but should work an other archs also. It supports UBR, CBR, ABR and VBR;
AAL0, AAL5 and AALraw. As an additional feature VCI/VPI 0/0 can be
opened for receiving in AALraw mode and receives all cells not claimed
by other open VCs (even cells with invalid GFC, VPI and VCI fields and
OAM cells).
Thanks to Christian Bucari from ProSum for lending two cards and answering
my questions.
MFNetBSD: revision 1.137
date: 2003/01/20 07:12:13; author: simonb;
Grrr. So much for my ability to use grep(1) effectively. Pointed out
by Stephen Degler in private mail.
date: 2002/12/10 14:07:37; author: toshii; state: Exp; lines: +6 -6
Add a couple of le32toh which were missing in the previous.
Pointed out by SOMEYA Yoshihiko.
date: 2002/12/07 07:33:20; author: toshii; state: Exp; lines: +50 -29
Update xfer->frlengths for input isoc transfer. Based on patches from
SOMEYA Yoshihiko.
Also fix error handling for isoc transfer somewhat; usb_transfer_complete
shouldn't be called for more than once.
date: 2002/12/07 07:14:28; author: toshii;
Fix several nits. Mostly from SOMEYA Yoshihiko.
- Call usbd_transfer_complete at splusb.
- Fix a botched for loop in ohci_rem_ed.
- In ohci_close_pipe, wait 1ms after removing an ED to avoid possible race
condition.
The splusb change is non-functional on FreeBSD.
The botched loop and race condition changes came from us.
This patch is non-functional.
date: 2002/09/29 20:58:25; author: augustss;
Add some spl calls to protect critical regions. From kern/18440,
Takeshi Nakayama.
(No functional change on FreeBSD).
date: 2002/12/31 02:21:31; author: dsainty;
Be somewhat more persuasive about enabling the port on a port reset.
USB protocol dictates that the port enable must be implied by the port
reset. To implement this on (at least) the VIA VT83C572 this means we
need to wait around tweaking the chip state until the port actually
transitions to enabled (or the device goes away). Likely fixes
kern/11018.
get a Hub descriptor, we have to set req.wValue to "Descriptor Type
and Descriptor Index". In this case, Descriptor Type is 0x29
(UDESC_HUB), Descriptor Index should be 0.
If I don't do a check (dev->address > 1 ... ), root hub fails.
A new Cytronix 4-port USB 2.0 Hub (Cypress CY7C65640 chip) now works
after this patch.
Submitted by: Alexander Pohoyda <alexander.pohoyda@gmx.net>
MFC after: 7 days
64-bit counters that wrap on overflow. They are collecte once per
second from the chips. Currently they can be retrieved via a sysctl phy_stats.
A write of an arbitrary value to the sysctl atomically retrieves the
statistics and clears them.
* Use ACPI_BUFFER as the type for AcpiGetObjectInfo
* Remove AcpiEnableEvent/AcpiClearEvent for ACPI_EVENT_FIXED (power/sleep
buttons) as they are no longer needed
* Change calls to use the new GPE functions
* Add AcpiOs*Lock functions
Even if we have no AT keyboard, an AT keyboard is registered because
it's probed with KB_CONF_PROBE_ONLY flag set during console initialization.
Unregister the keyboard if it doesn't present while second probe.
This should fix USB keyboard only case without 'kbdcontrol -k /dev/kbd1'.
(mainly the 3Com 3c996B/BCM5701).
For some reason that I don't fully understand, the 5701 signals PCS
encoding errors as though they were link change events, i.e. the 'link
state changed' bit in the status word of the status block is updated
and an interrupt is generated. This would cause the bge_tick() function
to be invoked and a "gigabit link up" message to be printed on the console.
To avoid this, the interrupt handler now checks the MAC status register
when a link change interrupt is triggered, and it will only call the
bge_tick() function if the 'PCS encoding error detected' bit is clear.
(This change should have no effect on copper NICs since this bit can
only ever be set in TBI mode. I do not know how it affects 5704 NICs
with a BCM8002 SERDES PHY.)
Special thanks to: Sherry Rogers at UCB for allowing me access to one
of their traffic monitor boxes so I could diagnose this problem.
- MN-110 10/100 USB ethernet (ADMtek Pegasus II, if_aue)
- MN-120 10/100 cardbus (ADMtek Centaur-C, if_dc)
- MN-130 10/100 PCI (ADMtek Centaur-P, if_dc)
Also update dc(4) man page to mention support for MN-120 and MN-130.
* Always use polled mode. The intr approach did not work for many
controllers and required the hw.acpi.ec.event_driven workaround.
* Only use an edge (not level) triggered GPE handler
* Add sc->ec_mtx for locking operations to a single EC. There were
many race conditions earlier between an SCI event and EcRead/Write.
* Use 1 ms as the global lock timeout
* Only acquire global lock if _GLK != 0
* Update EcWaitEvent to use an incremental backoff delay in its
poll loop. Wait 50 ms max instead of 10. Most ECs respond
in < 5 us (50 us when heavily loaded). However, some time out
occasionally even with a 10 ms timeout. For delays past 1 ms, use
msleep instead of DELAY to give SCI interrupts a chance to occur.
* Add EcCommand to send a command and wait for the appropriate event.
* The hw.acpi.ec.event_driven tunable is no longer applicable and
has been removed.
Ideas from: Linux
bus_dma_tag_create. We need to be sure that our packets are
kept in-sequence (that's how ATM is supposed to work) and
therefor use BUS_DMA_NOWAIT in all calls to bus_dmamap_load.
For memory allocated with bus_dmamem_alloc the use of anything
other than NULL arguments for the locking is anyway bogus because
this memory never should need bouncing and hence the load should never
be defered.
Allow the receipt of OAM and RM cells on raw connections. Caveat: it seems
that RM cells are still processed by the hardware even when we open the
connection as UBR.
extra trailing space.
- Don't bother probing a generic ISA bus device if isab0 already exists.
Some BIOSes place an ACPI psuedo-device with the HID of a generic ISA bus
device under the PCI-ISA bridge device. This is not the best solution
but will work for now. The isa bus driver only allows for one ISA bus
anyways.
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
- Factor out code common to all ISA bridge drivers attach methods into a
isab_attach() function.
- Rename the PCI-ISA bridge driver's attach function to pci_isab_attach()
and have it call isab_attach().
the bulk out buffer size to 16 bytes. The bulk out endpoint descriptor
reports 32 bytes, but if you use this value, data will get dropped.
Reviewed/approved by: scottl
to have this driver working on sparc64. It still needs to be made
endian-clean before it can work there.
Special thanks to dragonk@evilcode.net for sending me a dc(4) card so
that I was able to do this work.
Many cheers to all the people that tested this change, thanks to them,
this change shouldn't break anything :-).
Tested by: marcel (i386 and ia64), ru (i386), wilko (alpha),
mbr (i386), wpaul (i386) and
Will Saxon <WillS@housing.ufl.edu> (i386)
