still relevant (ISA cards can still be in EISA mode, and we're still
ignoring those in the identify routine). Notes about cards in EISA
mode have been left in the manual since they aren't relevant to EISA
support, but instruct how to properly configure an ISA card in a mode
when it is in a ISA bus slot.
support. Fix a comment block that's shared with both vx and ep. Remove
obsolete refernce to statically compiling a kernel with a fixed number
of vx devices. Have not removed EISA from the title of the document
the register definitions were originally derived from (though no doubt
more recent docments were also consulted).
inet_ntoa() cannot be used safely in a multithreaded environment
because it uses a static local buffer. Instead, use inet_ntoa_r()
with a buffer on the caller's stack.
Suggested by: glebius, emaste
Reviewed by: gnn
MFC after: 2 weeks
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D9625
machines, only a few 486 machines that used it, and those haven't had
enough memory to run FreeBSD for quite some time (often limited to
16MB).
Not to be confused with the Machine Check Architecture, which is still
very much alive and used (and untouched by this commit).
No Objection From: arch@
I found that at least with Chelsio NICs TOE sockets quite often report
negative sbspace() values. Using unsigned variable to store it resulted
in attempts to aggregate too much data in one sosend() call, that caused
errors and following connection termination.
MFC after: 2 weeks
The {powerpc,powerpc64,sparc64} LINT kernel builds fail with this error:
sys/dev/vt/vt_buf.c:198: warning: 'vtbuf_htw' defined but not used
Move vtbuf_htw() inside the '#if SC_NO_CUTPASTE' block where it belongs, and
put it in the proper order.
This fixes the immedate issue w/ vt(4), but all three then fail on different
issues.
Reviewed by: emaste
Current bxe probe function won't attach to devices with the NetXtreme II
BCM57840 2x20GbE chip, enable it by adding it's chip ID to the list of
supported chips.
Tested on: HP ProLiant WS460c Gen9
Reviewed by: gnn
MFC after: 1 week
Sponsored by: Citrix Systems R&D
Differential Revision: https://reviews.freebsd.org/D9609
we will import a newer version of the Linux code so the linuxkpi was not
used.
This is still missing 10G support, and multicast has not been tested.
Reviewed by: gnn
Obtained from: ABT Systems Ltd
Sponsored by: SoftIron Inc
Differential Revision: https://reviews.freebsd.org/D8549
On laptops like the ThinkPad X240, ClickPad buttons are located at the
top. The hw.psm.synaptics.softbuttons_y sysctl was supposed to allow this
by setting the value to a negative one (e.g. -1700). However, the
condition was wrong (double negative), and doing that placed the buttons
in an unreachable area.
PR: 216342
Submitted by: Greg V <greg@unrelenting.technology>
MFC after: 1 week
All this code is based on assumption that data will be stored in one piece,
and since buffer size if known and fixed, it is easier to hardcode it.
MFC after: 2 weeks
In general case m_pullup() does not really guarantee any data alignment.
Instead of depenting on side effects caused by data being always copied
out of mbuf cluster (which is probably a bug by itself), always allocate
aligned BHS buffer and read data there directly from socket.
While there, reuse new icl_conn_receive_buf() function to read digests.
The code could probably be even more optimized to aggregate those reads,
but until that done, this is still easier then the way it was before.
MFC after: 2 weeks
Add ACPI device 80860F14 with _UID 3 to the list of known devices. It
make SD card available on NUCs and Minnowboard. Previously added _UID 1
covered only eMMC devices.
Reported by: kib@
MFC after: 1 week
ip_data_mbuf is always appended to ip_bhs_mbuf, so it does not need own
packet header. This change first avoids allocation/initialization of the
header, and then avoids dropping one when it later gets to socket buffer.
MFC after: 2 weeks
meta-data, copy it into the softc structure.
When returning md(4) device details to the caller, include the file name in
any MD_PRELOAD type devices if it is set (first character is not NUL.)
In mdconfig, for "preload" type md(4) devices, if there is file config
available, print it in the file column of the output.
Reviewed by: brooks
Approved by: sjg (mentor)
MFC after: 1 month
Sponsored by: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D9529
Return full channel list via iwi_getradiocaps() method
(ieee80211_init_channels() was replaced with iwi_getradiocaps()
to be consistent with other drivers).
PR: 216923
Submitted and tested by: ds@ukrhub.net (original patch)
MFC after: 5 days
em_local_timer() executions during normal operation and was very likely
to cause a lock up on igb(4) devices.
Submitted by: Matt Macy (mmacy@nextbsd.org)
Reported by: jtl
Reviewed by: gallatin
Sponsored by: Limelight Networks & Netflix
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
The isp(4) driver was changing the tag type for REQUEST SENSE
commands to Head of Queue, when the CAM CCB flag
CAM_TAG_ACTION_VALID was NOT set. CAM_TAG_ACTION_VALID is set
when the tag action in the XPT_SCSI_IO is not CAM_TAG_ACTION_NONE
and when the target has tagged queueing turned on.
In most cases when CAM_TAG_ACTION_VALID is not set, it is because
the target is not doing tagged queueing. In those cases, trying to
send a Head of Queue tag may cause problems. Instead, default to
sending a simple tag.
IBM tape drives claim to support tagged queueing in their standard
Inquiry data, but have the DQue bit set in the control mode page
(mode page 10). CAM correctly detects that these drives do not
support tagged queueing, and clears the CAM_TAG_ACTION_VALID flag
on CCBs sent down to the drives.
This caused the isp(4) driver to go down the path of setting the
tag action to a default value, and for Request Sense commands only,
set the tag action to Head of Queue.
If an IBM tape drive does get a Head of Queue tag, it rejects it with
Invalid Message Error (0x49,0x00). (The Qlogic firmware translates that
to a Transport Error, which the driver translates to an Unrecoverable
HBA Error, or CAM_UNREC_HBA_ERROR.) So, by default, it wasn't possible
to get a good response from a REQUEST SENSE to an FC-attached IBM
tape drive with the isp(4) driver.
IBM tape drives (tested on an LTO-5 with G9N1 firmware and a TS1150
with 4470 firmware) also have a bug in that sending a command with a
non-simple tag attribute breaks the tape drive's Command Reference
Number (CRN) accounting and causes it to ignore all subsequent
commands because it and the initiator disagree about the next
expected CRN. The drives do reject the initial command with a head
of queue tag with an Invalid Message Error (0x49,0x00), but after that
they ignore any subsequent commands. IBM confirmed that it is a bug,
and sent me test firmware that fixes the bug. However tape drives in
the field will still exhibit the bug until they are upgraded.
Request Sense is not often sent to targets because most errors are
reported automatically through autosense in Fibre Channel and other
modern transports. ("Modern" meaning post SCSI-2.) So this is not
an error that would crop up frequently. But Request Sense is useful on
tape devices to report status information, aside from error reporting.
This problem is less serious without FC-Tape features turned on,
specifically precise delivery of commands (which enables Command
Reference Numbers), enabled on the target and initiator. Without
FC-Tape features turned on, the target would return an error and
things would continue on.
And it also does not cause problems for targets that do tagged
queueing, because in those cases the isp(4) driver just uses the
tag type that is specified in the CCB, assuming the
CAM_TAG_ACTION_VALID flag is set, and defaults to sending a Simple
tag action if it isn't an ordered or head of queue tag.
sys/dev/isp/isp.c:
In isp_start(), don't try to send Request Sense commands
with the Head of Queue tag attribute if the CCB doesn't
have a valid tag action. The tag action likely isn't valid
because the target doesn't support tagged queueing.
Sponsored by: Spectra Logic
MFC after: 3 days
When using Blue-Flame, BF, the QPN overrides the VLAN, CV, and SV
fields in the WQE. Thus, BF may only be used for QPNs with bits 6,7
unset.
The current ethernet driver code reserves a TX QP range with 256b
alignment.
This is wrong because if there are more than 64 TX QPs in use, QPNs >=
base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for "Eth
QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have bits
6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required
attributes for this QP. Those attributes are considered "best-effort".
If an attribute, such as Ethernet BF enabled QP, is a must-have
attribute, the function has to check that attribute is supported
before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those
attributes and masks out unsupported attributes as well. In order to
notify VFs which attributes are supported, the VF uses QUERY_FUNC_CAP
command. This command's mailbox is filled by the PF, which notifies
which QP allocation attributes it supports.
Obtained from: Linux (dual BSD/GPLv2 licensed)
Submitted by: Dexuan Cui @ microsoft . com
Differential Revision: https://reviews.freebsd.org/D8868
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
Previously, the mlx4 driver queried the firmware in order to get the
number of supported EQs. Under SRIOV, since this was done before the
driver notified the firmware how many VFs it actually needs, the
firmware had to take into account a worst case scenario and always
allocated four EQs per VF, where one was used for events while the
others were used for completions. Now, when the firmware supports the
asymmetric allocation scheme, denoted by exposing num_sys_eqs > 0 (-->
MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the QUERY_FUNC command to query
the firmware before enabling SRIOV. Thus we can get more EQs and MSI-X
vectors per function. Moreover, when running in the new
firmware/driver mode, the limitation that the number of EQs should be
a power of two is lifted.
Obtained from: Linux (dual BSD/GPLv2 licensed)
Submitted by: Dexuan Cui @ microsoft . com
Differential Revision: https://reviews.freebsd.org/D8867
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
The hpt27xx(4), hptnr(4), and hptrr(4) drivers declare MIN() and MAX()
internally which match the macros from sys/param.h.
MIN() is not used, MAX is only used once and can be replaced with the
max() version in libkern.h which operates on u_ints.
MFC after: 2 weeks
Refresh upstream driver before impending conversion to iflib.
Major new features:
- Support for Fortville-based 25G adapters
- Support for I2C reads/writes
(To prevent getting or sending corrupt data, you should set
dev.ixl.0.debug.disable_fw_link_management=1 when using I2C
[this will disable link!], then set it to 0 when done. The driver implements
the SIOCGI2C ioctl, so ifconfig -v works for reading I2C data,
but there are read_i2c and write_i2c sysctls under the .debug sysctl tree
[the latter being useful for upper page support in QSFP+]).
- Addition of an iWARP client interface (so the future iWARP driver for
X722 devices can communicate with the base driver).
- Compiling this option in is enabled by default, with "options IXL_IW" in
GENERIC.
Differential Revision: https://reviews.freebsd.org/D9227
Reviewed by: sbruno
MFC after: 2 weeks
Sponsored by: Intel Corporation
This implements hardware assisted quiet IE support. Quiet time is
an optional interval on DFS channels (but doesn't have to be DFS
only channels! sigh) where the station and AP can be quiet in order
to allow for channel utilisation measurements. Typically that's
stuff like radar detection, spectral scan, other-BSS frame sniffing,
checking how busy the air is, etc.
The hardware implements it as one of the generic timers, which is
supplied a period, offset from the trigger period and duration
to stay quiet. The AP can announce quiet time configurations which
change, and so this code also tracks that.
Implementation details:
* track the current quiet time IE
* compare the new one against the previous one - if only the TBTT
counter changes, don't update things
* If tbttcount=1 then program it into the hardware - that is when
it is easiest to program the correct starting offset (one TBTT +
configured offset).
* .. later on check to see if it can be done on any tbttcount
* If the IE goes away then remove the quiet timer and clear the
config
* Upon reset, state change, new beacon - clear quiet time IE
and just let it resync from the next beacon.
History:
This was work done initially by sibridgetech.com in 2011/2012/2013
as part of some FreeBSD wifi DFS contracting work they had for a
third party. They implemented the net80211 quiet time IE pieces
and had some test code for the station side which didn't entirely
use the timers correctly.
I figured out how to use the timers correctly without stopping/starting
the transmit DMA engine each time. When done correctly, the timer
just needs to be programmed once and left alone until the next
configuration change.
So, thanks to Himali Patel and Parthiv Shah for their work way
back then. I finally figured it out and finished it!
TODO:
* Now, I'd rather net80211 did the quiet time IE tracking and parsing,
pushing configurations into the driver is needed. I'll look at
doing that in a subsequent update.
* This doesn't handle multiple quiet time IEs, which will currently
just mess things up. I'll look into supporting that in the future
(at least by only obeying "one" of them, and then ignoring
subsequent IEs in a beacon/probe frame.)
* This also implements the STA side and not the AP side - the AP
side will come later, and involves taking various other intervals
into account (eg the beacon offset for multi-VAP modes, the
SWBA time, etc, etc) as well as obtaining the configuration when
a beacon is configured/generated rather than "hearing" an IE.
* .. investigate supporting quiet IE in mesh, tdma, ibss modes
* .. investigate supporting quiet IE for non-DFS channels
(so this can be done for say, 2GHz channels.)
* Chances are i should commit NULL methods for the ar5210, ar5211 HALs..
Tested:
* AR9380, STA mode - announcing quiet, removing quiet, changing quite
time config, whilst doing iperf testing;
* AR9380, AP mode.
Some U-Boot versions do not initialize MT7620's Frame Engine.
Then it is not possible to receive packets from the network.
Setting GDMA1 Frames Destination Port to Port 0 (CPU) in GDM Forwarding
Configuration register solves this issue.
Submitted by: Hiroki Mori (yamori813@yahoo.co.jp)
Reviewed by: adrian mizhka (previous version)
Differential Revision: https://reviews.freebsd.org/D9301
using the ACPI C1/mwait sleep method.
Previously, the mwait instruction would return when an interrupt was
pending; however, the idle loop did not actually enable interrupts when
this occurred. This led to a situation where the idle loop could quickly
spin through the C1/mwait sleep method a number of times when an interrupt
was pending. (Eventually, the situation corrected itself when something
other than an interrupt triggered the idle loop to either enable interrupts
or schedule another thread.)
Reviewed by: kib, imp (earlier version)
Input from: jhb
MFC after: 1 week
Sponsored by: Netflix
The 1s delay was added in the update to version 16 fw, where Family 8000
support was added.
Obtained from: DragonflyBSD commit bb480ca679a7ea530bdca6e41082d5755e9751dc
* Add the command groups enum, and the iwm_phy_ops_subcmd_ids enum
to if_iwmreg.h definitions.
* The IWM_DTS_MEASUREMENT_NOTIF_WIDE notification will be generated by
version 17 firmware.
Taken-From: Linux iwlwifi
Obtained from: DragonflyBSD commit 4d8d6f9def2ffb60aaf2d88f72f069a96c0b4e3f
* Adds IWM_DEBUG_TEMP debug message type, for printing messages related
to temperature sensors and thermal/TDP infos.
* The firmware regularly sends us DTS measurement notifications, so just
print the temperature value as a debugging message.
(Adrian's addition):
* Eventually this can be used by the driver to limit transmit rate / power to
try and do some thermal throttling.
Obtained from: DragonflyBSD commit efb7d4eb5c3140889a8880e12fd83c7bbfd0059d
* Add iwm_pcie_set_cmd_in_flight() and iwm_pcie_clear_cmd_in_flight()
helper methods.
* Use ring->queued tracking in the command queue to set/clear the
cmd_hold_nic_awake bit at the right points.
Taken-From: Linux iwlwifi
Obtained from: DragonflyBSD commit ce43f57f5308b579ea21e8a5a29969114ba2247d
* Add IWM_FLAG_SCAN_RUNNING to sc->sc_flags to track whether the firmware
is currently running a scan, in order to decide wheter iwm_scan_end
needs to abort a running scan.
* In iwm_scan_end, if the scan is still running, we now abort it, in order
to keep the firmware scanning state in sync.
* Try to make things a bit simpler, by reacting on the
IWM_SCAN_OFFLOAD_COMPLETE and IWM_SCAN_COMPLETE_UMAC notifications,
instead of IWM_SCAN_ITERATION_COMPLETE and
IWM_SCAN_ITERATION_COMPLETE_UMAC. This should be fine since we always
only tell the firmware to do a single scan iteration anyway.
Obtained from: DragonflyBSD commit 1f249c981c4e89e7cde1836a75b61cac36dc7ac5
* Uses the notification wait api to wait for the corresponding scan
complete notification after sending the abort command.
Taken-From: Linux iwlwifi
Obtained from: DragonflyBSD commit b484d09d54301740f036ddf02008117f563960c2
