If the value from the user is less than 177, assume it is a multiple of
a single speed CDROM and convert to KB/sec.
No complaints from: sos
Reviewed by: ken
Approved by: re
MFC after: 1 day
This code allows a user program to enable target mode on a SIM and
then emulate any number of devices (disks, tape drives, etc.) All
decisions about device behavior (UA, CA, inquiry response) are left
to the usermode program and the kernel driver is merely a conduit
for CCBs. This enables multiple concurrent target emulators, each
using its own backing store and IO model.
Also included is a user program that emulates a disk (RBC) using a
file as a backing store. This provides functionality similar to
md(4) at the CAM layer.
Code has been tested on ahc(4) and should also work on isp(4) (and
other SIMs that gain target mode support). It is a complete rewrite
of /sys/cam/scsi_target* and /usr/share/examples/scsi_target.
Design, comments from: gibbs
Supported by: Cryptography Research
Approved by: re
* Change atapi-cd ioctls to use the same units.
* Change burncd, cdcontrol to convert CDROM speed to KB/sec before
calling the ioctl. Add a "max" speed option for their command lines.
This change does not break ABI but does change the units passed through
the ioctl so 3rd party software that uses cdrio.h will have to convert
(most likely by multiplying CDROM speed by 177 to get KB/s).
PR: kern/36845
Submitted by: Philipp Mergenthaler <p@i609a.hadiko.de> (CAM ioctls)
Reviewed by: sos, ken
MFC after: 1 month
Requested by: Most developers
Apologies to: Most developers, with special note to <ken@kdm.org>
Collabroation in the future with: Kenneth D. Merry <ken@kdm.org>
structure. This has been broken since 1998, but probably hasn't been
noticed because it takes a read/write of 64K blocks (32MB with 512 byte
blocks) to trigger using the 12 byte read/write CDB in scsi_read_write().
Submitted by: "Moore, Eric Dean" <emoore@lsil.com>
MFC after: 3 days
SCSI disks are too square pegs for the round holes in both of these.
And since atapi-cd has clearly shown that there are better acccess
models for CD media than trying to pretend to be a classical disk,
we stop the masquerade rather than patch up the costume.
But do implement the DIOCGMEDIASIZE and DIOCGSECTORSIZE so it will
be possible to manually attach to GEOM, should some the need arise.
Ideally, this driver should do media-detection and call make_dev()
when a CD is inserted and destroy_dev() when it is removed, this
would allow our future devd(8) to automount etc etc but coding that
takes SCSI-clue beyond anything I posses.
Tested on: sparc64
and predictable way, and I apologize if I have gotten it wrong anywhere,
getting prior review on a patch like this is not feasible, considering
the number of people involved and hardware availability etc.)
If struct disklabel is the messenger: kill the messenger.
Inside struct disk we had a struct disklabel which disk drivers used to
communicate certain metrics to the disklayer above (GEOM or the disk
mini-layer). This commit changes this communication to use four
explicit fields instead.
Amongst the benefits is that the fields do not get overwritten by
wrong or bogus on-disk disklabels.
Once that is clear, <sys/disk.h> which is included in the drivers
no longer need to pull <sys/disklabel.h> and <sys/diskslice.h> in,
the few places that needs them, have gotten explicit #includes for
them.
The disklabel inside struct disk is now only for internal use in
the disk mini-layer, so instead of embedding it, we malloc it as
we need it.
This concludes (modulus any mistakes) the series of disklabel related
commits.
I belive it all amounts to a NOP for all the rest of you :-)
Sponsored by: DARPA & NAI Labs.
* Only update cdb in place if not CDB_POINTER
* Correctly check for QFRZ before restarting CCB
* More accurate printf message
* style(9) changes at end
Patch tested successfully on Maxtor 4 G120J6 GAK8.
Include PPR option bits defined in SPI4.
scsi_iu.h:
Add data structures releated to parallel SCSI information units
for use in SPI4 packetized protocol.
and upgrade to using 10 byte cdbs.
As far as I tested, this works efficiently for most of the
SBP-II/Firewire devices but most of the umass devices still need
ad-hoc work around because umass-sim doesn't return any SCSI errors.
A sysctl nob is also added for the last resort.
I hope we don't need DA_Q_NO_6_BYTE quirks anymore.
Reviewed by: gibbs
MFC after: 1 week
deprecated in favor of the POSIX-defined lowercase variants.
o Change all occurrences of NTOHL() and associated marcros in the
source tree to use the lowercase function variants.
o Add missing license bits to sparc64's <machine/endian.h>.
Approved by: jake
o Clean up <machine/endian.h> files.
o Remove unused __uint16_swap_uint32() from i386's <machine/endian.h>.
o Remove prototypes for non-existent bswapXX() functions.
o Include <machine/endian.h> in <arpa/inet.h> to define the
POSIX-required ntohl() family of functions.
o Do similar things to expose the ntohl() family in libstand, <netinet/in.h>,
and <sys/param.h>.
o Prepend underscores to the ntohl() family to help deal with
complexities associated with having MD (asm and inline) versions, and
having to prevent exposure of these functions in other headers that
happen to make use of endian-specific defines.
o Create weak aliases to the canonical function name to help deal with
third-party software forgetting to include an appropriate header.
o Remove some now unneeded pollution from <sys/types.h>.
o Add missing <arpa/inet.h> includes in userland.
Tested on: alpha, i386
Reviewed by: bde, jake, tmm
time in the cases where it really sends the drive out to lunch, but it also
allows us to catch very wierd edge cases of strange drives that might take
a very long time (emulated disk drives over a network, e.g.).
quirk regarding the C- series makes me suspect that all Olympus models have
the same quirks, but I cannot prove it.
Submitted by: Bernd Walter <ticso@cicely8.cicely.de>
attempts to set buffered mode was printing out "unable to set buffered
mode" no matter what. Oops.
Spotted by: Joerg Wunsch <joerg_wunsch@uriah.heep.sax.de>
MFC after: 3 weeks
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
Clear residual counts after a successful samount (the user doesn't
care that we got an N-kbyte residual on our test read).
Change a lot of error handling code.
1. If we end up in saerror, check more carefully about the kind of
error. If it is a CAM_SCSI_STATUS_ERROR and it is a read/write
command, we'll be handling this in saerror. If it isn't a read/write
command, check to see whether this is just an EOM/EOP check condition-
if it is, just set residual and return normally. A residual and
then a NO SENSE check condiftion with the ASC of 0 and ASCQ of
between 1 and 4 are normal 'signifying' events, not errors per se,
and we shouldn't give the command to cam_periph_error to do something
relatively unpredictable with.
2. If we get a Bus Reset, had a BDR sent, or get the cam status of
CAM_REQUEUE_REQ, check the retry count on the command. The default
error handler, cam_periph_error, doesn't honor retry count in these
cases. This may change in the future, but for now, make sure we
set EIO and return without calling cam_periph_error if the retry
count for the command with an error is zero.
3. Clean up the pending error case goop and handle cases more
sensibly.
The rules are:
If command was a Write:
If we got a SSD_KEY_VOLUME_OVERFLOW, the resid is
propagated and we set ENOSPC as the error.
Else if we got an EOM condition- just mark EOM pending.
And set a residual of zero. For the longest time I was just
propagating residual from the sense data- but my tape
comparison tests were always failing because all drives I
tested with actually *do* write the data anyway- the EOM
(early warning) condition occurred *prior* to all of the
data going out to media- that is, it was still buffered by
the drive. This case is described in SCSI-2, 10.2.14,
paragraph #d for the meaning of 'information field'. A
better fix for this would be to issue a WFM command of zero
to cause the drive to flush any buffered data, but this
would require a fairly extensive rewrite.
Else if the command was a READ:
If we got a SSD_KEY_BLANK_CHECK-
If we have a One Filemark EOT model- mark EOM as pending,
otherwise set EIO as the erorr.
Else if we found a Filemark-
If we're in Fixed Block mode- mark EOF pending.
If we had an ILI (Incorrect Length Indicator)-
If the residual is less than zero, whine about tape record
being too big for user's buffer, otherwise if we were in
Fixed Block mode, mark EIO as pending.
All 'pending' conditions mean that the command in question completes
without error indication. It had succeeded, but a signifying event
occurred during its execution which will apply to the *next* command
that would be exexcuted. Except for the one EOM case above, we always
propagate residual.
Now, way back in sastart- if we notice any of the PENDING bits set,
we don't run the command we've just pulled off the wait queue. Instead,
we then figure out it's disposition based upon a previous command's
association with a signifying event.
If SA_FLAG_EOM_PENDING is set, we don't set an error. We just complete
the command with residual set to the request count (not data moved,
but no error). We continue on.
If SA_FLAG_EOF_PENDING- if we have this, it's only because we're in
Fixed Block mode- in which case we traverse all waiting buffers (which
we can get in fixed block mode because physio has split things up) and
mark them all as no error, but no data moved and complete them.
If SA_FLAG_EIO_PENDING, just mark the buffer with an EIO error
and complete it.
Then we clear all of the pending state bits- we're done.
MFC after: 4 weeks
Handle both old and new TARGIOALLOCUNIT/TARGIOFREEUNIT cases- the new
one allows us to specify inquiry data we want to use.
Handle more of the CAM_DIS_DISCONNECT case.
Move TARGCTLIOALLOCUNIT to OTARGCTLIOALLOCUNIT, TARGCTLIOFREEUNIT
to OTARGCTLIOFREEUNIT and redefine old associated structure to be
old_ioc_alloc_unit- deprecation but preservation of binaries.
Add new structure for same- but this one contains a pointer to
user defined INQUIRY data so you can define what the target
device looks like to the outside world.
1. If we get frozen, unfreeze for disable disconnects.
2. Put CAM_DIS_DISCONNECT commands at the head of the work queue
(we have a target still connected and we can't run anything else
until this command completes).
If we had an error sending the last CTIO, unfreeze the queue anyway.
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
This is useful if you want to dynamically move into a Fibre Channel
or Multi-initiator environment that happens to be particularly noisy
and ugly that requires a lot of retries (with shorter I/O timeouts)
for commands destried by LIPs or Bus Resets.
Reviewed by: deafening silence on audit && scsi on the retry counts
MFC after: 2 weeks
1. Add SA_IO_TIMEOUT as an option (4 minutes default) to cover reads,
writes, wfm, test unit ready.
2. Add internal SCSIOP_TIMEOUT (e.g., for mode sense) at 1 minute. This
should not require an option, but is cleaner to parameterize.
MFC after: 1 week
drivers.
- change daprevent() to set CAM_RETRY_SELTO and SF_RETRY_UA when it calls
cam_periph_runccb().
- change the pt(4) driver to ignore unit attentions
- change the targ(4) driver to retry selection timeouts
- clean up a few formatting glitches in the targ(4) driver
Reviewed by: gibbs
prevent scsi_sense_desc() from deferencing a NULL pointer when a drive
happens to return one of these sense keys.
Reported by: Michael Samuel <michael@miknet.net>
With the recent changes in the CAM error handling, some problems in
the error handling of sa(4) have been uncovered. Basically, a number
of conditions that are not actually errors have been mistreated as
genuine errors. In particular:
. Trying to read in variable length mode with a mismatched blocksize
between the on-tape (virtual) blocks and the read(2) supplied buffer
size, causing an ILI SCSI condition, have caused an attempt to retry
the supposedly `errored' transfer, causing the tape to be read
continuously until it eventually hit EOM. Since by default any
simple mt(1) operation does an initial test read, an `mt stat' was
sufficient to trigger this bug.
Note that it's Justin's opinion that treating a NO SENSE as an EIO
is another bug in CAM. I feel not authorized to fix cam_periph.c
without another confirmation that i'm on the right track, however.
. Hitting a filemark caused the read(2) syscall to return EIO, instead
of returning a `short read'. Note that the current fix only solves
this problem in variable length mode. Fixed length mode uses a
different code path, and since i didn't grok all the intentions behind
that handling, i did not touch it (IOW: it's still broken, and you get
an EIO upon hitting a filemark).
The solution is to keep track of those conditions inside saerror(),
and upon completion to not call cam_periph_error() in that case. We
need to make sure that the device gets unfrozen if needed though (in
case of actual errors, cam_periph_error() does this on our behalf).
Not objected by: mjacob (who currently doesn't have the time to
review the patch)
Some of the major changes include:
- The SCSI error handling portion of cam_periph_error() has
been broken out into a number of subfunctions to better
modularize the code that handles the hierarchy of SCSI errors.
As a result, the code is now much easier to read.
- String handling and error printing has been significantly
revamped. We now use sbufs to do string formatting instead
of using printfs (for the kernel) and snprintf/strncat (for
userland) as before.
There is a new catchall error printing routine,
cam_error_print() and its string-based counterpart,
cam_error_string() that allow the kernel and userland
applications to pass in a CCB and have errors printed out
properly, whether or not they're SCSI errors. Among other
things, this helped eliminate a fair amount of duplicate code
in camcontrol.
We now print out more information than before, including
the CAM status and SCSI status and the error recovery action
taken to remedy the problem.
- sbufs are now available in userland, via libsbuf. This
change was necessary since most of the error printing code
is shared between libcam and the kernel.
- A new transfer settings interface is included in this checkin.
This code is #ifdef'ed out, and is primarily intended to aid
discussion with HBA driver authors on the final form the
interface should take. There is example code in the ahc(4)
driver that implements the HBA driver side of the new
interface. The new transfer settings code won't be enabled
until we're ready to switch all HBA drivers over to the new
interface.
src/Makefile.inc1,
lib/Makefile: Add libsbuf. It must be built before libcam,
since libcam uses sbuf routines.
libcam/Makefile: libcam now depends on libsbuf.
libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the
sbuf sources from sys/kern.
bsd.libnames.mk: Add LIBSBUF.
camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically
linked, we can't depend on the dynamic linker
to pull in libsbuf.
camcontrol.c: Use cam_error_print() instead of checking for
CAM_SCSI_STATUS_ERROR on every failed CCB.
sbuf.9: Change the prototypes for sbuf_cat() and
sbuf_cpy() so that the source string is now a
const char *. This is more in line wth the
standard system string functions, and helps
eliminate warnings when dealing with a const
source buffer.
Fix a typo.
cam.c: Add description strings for the various CAM
error status values, as well as routines to
look up those strings.
Add new cam_error_string() and
cam_error_print() routines for userland and
the kernel.
cam.h: Add a new CAM flag, CAM_RETRY_SELTO.
Add enumerated types for the various options
available with cam_error_print() and
cam_error_string().
cam_ccb.h: Add new transfer negotiation structures/types.
Change inq_len in the ccb_getdev structure to
be "reserved". This field has never been
filled in, and will be removed when we next
bump the CAM version.
cam_debug.h: Fix typo.
cam_periph.c: Modularize cam_periph_error(). The SCSI error
handling part of cam_periph_error() is now
in camperiphscsistatuserror() and
camperiphscsisenseerror().
In cam_periph_lock(), increase the reference
count on the periph while we wait for our lock
attempt to succeed so that the periph won't go
away while we're sleeping.
cam_xpt.c: Add new transfer negotiation code. (ifdefed
out)
Add a new function, xpt_path_string(). This
is a string/sbuf analog to xpt_print_path().
scsi_all.c: Revamp string handing and error printing code.
We now use sbufs for much of the string
formatting code. More of that code is shared
between userland the kernel.
scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly
useful in the first place.
Add a new error action, SS_REQSENSE. (Send a
request sense and then retry the command.)
This is useful when the controller hasn't
performed autosense for some reason.
Change the default actions around a bit.
scsi_cd.c,
scsi_da.c,
scsi_pt.c,
scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection
timeouts shouldn't be covered by a sense flag.
scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO.
Get rid of the last vestiges of a read/write
interface.
libkern/bsearch.c,
sys/libkern.h,
conf/files: Add bsearch.c, which is needed for some of the
new table lookup routines.
aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if
CAM_NEW_TRAN_CODE is defined.
sbuf.h,
subr_sbuf.c: Add the appropriate #ifdefs so sbufs can
compile and run in userland.
Change sbuf_printf() to use vsnprintf()
instead of kvprintf(), which is only available
in the kernel.
Change the source string for sbuf_cpy() and
sbuf_cat() to be a const char *.
Add __BEGIN_DECLS and __END_DECLS around
function prototypes since they're now exported
to userland.
kdump/mkioctls: Include stdio.h before cam.h since cam.h now
includes a function with a FILE * argument.
Submitted by: gibbs (mostly)
Reviewed by: jdp, marcel (libsbuf makefile changes)
Reviewed by: des (sbuf changes)
Reviewed by: ken
inq_len member of the ccb_getdev structure, but we've never filled that
value in..
So we now get the length from the inquiry data returned by the drive.
(Since we will fetch as much inquiry data as the drive claims to support.)
Reviewed by: mjacob
Reported by: Andrzej Tobola <san@iem.pw.edu.pl>
o Offset and period in synch messages and width negotiation should be
done for per target not per lun. Move these from *lun_info to
*targ_info.
o Change in handling XPT_RESET_DEV and XPT_GET_TRAN_SETTINGS .
o Change CAM_* xpt_done return values.
o Busy loop did not timeout. Change this to timeout as original NetBSD/pc98.
Reviewed by: bsd-nomads ML
not be retried. It is an indication that there was an error that was
corrected during the execution of the command. This is per ANSI SCSI2
spec.
It's possible that these should also be noted to the console (as indicative,
perhaps, of growing media defect lists in drives), but the default of
printing errors out if bootverbose in this case is probably enough.
Also, there'd been a missing ERESTART for that clause anyway.
2. If you have an ABORTED COMMAND, it's almost invariably a SCSI parity
error. You should never be silent about these since users should do something
about this if it occurs (moving that power cord *away* from the SCSI cable is
always a good first start). This should print irrespective of bootverbose
because it's an actual real error even if we retry a transmission.
Reviewed by: audit@freebsd.org, gibbs@freebsd.org
we *really* are.
It should be noted that there is a degenerate case where soft tape
location will be lost (not causing a frozen state- but causing
the loss of reporting fileno/blockno)- that's where you backspace
over a filemark- you stop backspacing as soon as you cross the
filemark, but you have no idea what the record number now is because
you have no idea how many records you are into the file you just
backed into. Such is life.
While I'm at it, also pick up residuals from writing filemarks.
PR: 24222
only CCB type but also extra flags- one of which can be "position
updated".
In other changes: Add in a SA_QUIRK_NO_CPAGE quirk so that it's possible
to avoid using a (broken) device's implementation of he DEVICE COMPRESSION
page.
Also do a couple of printout cleanups.
As per some discussion on FreeBSD-scsi, skip doing tape flushing
if we're reading tape logical block location (MTIOCRDSPOS).
MS will be treated as having this quirk. In the event that we falsely
identify one that doesn't need it, no harm will be done. Ken
suggested that we make this more generic since there may be more
needed in the future.
Reported by: TERAMOTO Masahiro <teramoto@comm.eng.osaka-u.ac.jp>
PR: kern/23378
Reviewed by: ken
field in CDB' error when attempting to start a caddy-type CD drive,
since those drives apparently in general refuse to load a medium. Since
we never advertised the feature to load the medium upon calling
cdstartunit() (i. e. upon receipt of a CDIOCSTART ioctl command), nobody
should have relied on it. Besides, nobody noticed so far at all that
this command is failing for caddy-type drives... Only few applications
seem to use it at all (among them is workman, which made me notice it).
Reviewed by: ken
CDs.
With audio CDs, you can't just do a READ(10) call on most drives without
first setting the blocksize with a mode select command. The disklabel code
does a read of the first sector of the media to find a label if it exists.
This caused drives to return an error when an audio CD was in the drive,
due to the problem described above.
The solution is to read the table of contents on the CD, and only attempt
to read the disklabel if the first track is a data track.
This works on all the various CD and DVD media I have tried, but further
testing (especially with Video CDs and other mode 2 media) will be
needed to determine if this is a universal solution.
This allows writing to DVD-RAM, PD and similar drives that probe as CD
devices. Note that these are randomly writeable devices, not
sequential-only devices like CD-R drives, which are supported by cdrecord.
Add a new flag value for dsopen(), DSO_COMPATLABEL. The cd(4) driver now
uses this flag instead of the DSO_NOLABELS flag. The DSO_NOLABELS always
used a "fake" disklabel for the entire disk, provided by the caller.
With the DSO_COMPATLABEL flag, dsopen() will first search the media for a
label, and if it finds a label, it will use that label. Otherwise it will
use the fake disklabel provided by the caller. This provides backwards
compatibility, since we will still have labels for ISO9660 media.
It also provides new functionality, since you can now have a regular BSD
disklabel on read-only media, or on writeable media (e.g. DVD-RAM).
Bruce and I both think that we should eventually (in a few years) get
away from using disklabels for ISO9660 media, and just use the whole disk
device (/dev/cd0). At that point disklabel handling in the cd(4) driver
could follow the "normal" model, as used in the da(4) driver.
Also, clean up the path in a couple of places in cdregister(). (Thanks to
Nick Hibma for catching that bug.)
Reviewed by: bde
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
(a NetBSD port for NEC PC-98x1 machines). They are ncv for NCR 53C500,
nsp for Workbit Ninja SCSI-3, and stg for TMC 18C30 and 18C50.
I thank NetBSD/pc98 and bsd-nomads people.
Obtained from: NetBSD/pc98
write caching is disabled on both SCSI and IDE disks where large
memory dumps could take up to an hour to complete.
Taking an i386 scsi based system with 512MB of ram and timing (in
seconds) how long it took to complete a dump, the following results
were obtained:
Before: After:
WCE TIME WCE TIME
------------------ ------------------
1 141.820972 1 15.600111
0 797.265072 0 65.480465
Obtained from: Yahoo!
Reviewed by: peter
for the Quantum "MAVERICK 540S" and "LPS525S".
Also, add common string variables, since we seem to have a few Quantum and
Micropolis drives in here.
Fix the 'quantum' variable usage in scsi_all.c that likely got broken when
someone staticized things in cam_xpt.c. (That particular problem would
cause Quantum Fireball ST drives to not get spun up if they were not
already spinning.)
Submitted by: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
to be obeying the original spec as to what the numeric value means.
Temperature flags are unaffected- these are still the 'pseudo-thermometers'
and overtemp/undertemp warnings will be caught and translated to SES objects
here.
PR: 20475
related patches. These include:
* Mode page editting can be scripted. This involves two
things: first, if stdin is not a tty, changes are read from
stdin rather than invoking $EDITOR. Second, and more
importantly, not all modepage entries must be included in the
change set. This means that camcontrol can now gracefully handle
more intrusive editting from the $EDITOR, including removal or
rearrangement of lines. It also means that you can do stuff
like:
# echo "WCE: 1" | camcontrol modepage da3 -m 8 -e
# newfs /dev/da3
# echo "WCE: 0" | camcontrol modepage da3 -m 8 -e
* Range-checking on user-supplied input values. modeedit.c now
uses the field width specifiers to determine the maximum
allowable value for a field. If the user enters a value larger
than the maximum, it clips the value to the max and warns the
user. This also involved patching cam_cmdparse.c to be more
consistent with regards to the "count" parameter to arg_put
(previously is was the length of strings and 1 for all integral
types). The cam_cdbparse(3) man page was also updated to reflect
the revised semantics.
* In the process, I removed the 64 entry limit on mode pages (not
that we were even close to hitting that limit). This was a nice
side-effect of the other changes.
* Technically, the new mode editting functionality allows editting
of character array entries in mode pages (type 'c' or 'z'),
however since buff_encode doesn't grok them it is currently
useless.
* Camcontrol gained two new options related to mode pages: -l and
-b. The former lists all available mode pages for a given
device. The latter forces mode page display in binary format
(the default when no mode page definition was found in
scsi_modes).
* Added support for mode page names to scsi_modes. Allows names to
be displayed alongside mode numbers in the mode page
listing. Updated scsi_modes to use the new functionality. This
also adds the semicolon into the scsi_modes syntax as an
optional mode page definition terminator. This is needed to name
pages without providing a page format definition.
* Updated scsi_all.h to include a structure describing mode page
headers.
* Added $FreeBSD$ line to scsi_modes.
Inspired by: dwhite
Reviewed by: ken
Clean up the comments related to the high speed
sync rate table for SPI.
scsi_message.h:
Bring in some SCSI3 message terminology. All SCSI2 names
are still preserved for backwards compatibility.
CAM_TAG_ACTION_VALID and CAM_DIR_MASK). Remove redundant
CAM_DEBUG line. Spiff up CAM_DEBUG printout for commands
and move the printout up to the top where we can see it,
even for the pending_ua/pending_ca cass. Add missing
newline in a CAM_DEBUG.
to splx(s) if cam_extend_get fails and we return ENXIO, reset ccb flags
when we push ATIOs back to the SIM, do some data increment fixes, set
priority of command based on whether CAM_DIS_DISCONNECT is set and related
changes).
Add in some more CAM_DEBUG_PERIPH debug statements and also add in support
for TARGIODEBUG which then will enable or disable CAM_DEBUG_PERIPH tracing
for an instance.
CAPACITY operation. SCSI-3 mandates this to be 2048, but some older
drives like my old Plasmon CD-R report weird numbers between 2048 and
up to 2352 bytes depending on the mode of the last track etc. This in
turn confuses stuff like the slice code since it refuses to work with
devices that do not have a blocksize which is a multiple of 512 bytes.
Reviewed by: ken
libcam/Makefile: Add scsi_da.c to libcam for the new
scsi_format_unit() function.
camcontrol.8: Update the man page for the new format
functionality, and take out the examples section
describing how to do it with 'camcontrol cmd'.
camcontrol.c: New format functionality. Note that unlike the
rest of the camcontrol subcommands, this one is
interactive by default. Because of the potential
destructiveness of the format command, I thought
it necessary to get confirmation from the user
before spamming a disk. You can disable the
interactive behavior, and the status meter with
command line arguments.
scsi_da.c: Add the new scsi_format_unit() cdb building
function and use #ifdef _KERNEL to make this file
compile in both the kernel and userland. The
format unit function is currently only defined in
the non-kernel case, because nothing in the kernel
is using it. If that changes, it should be
un-ifdefed and compiled in both cases.
scsi_da.h: New function declaration, CDB structure and format
data structures.
Thanks to Nick Hibma for providing some valuable input on these changes.
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
Add a SA_QUIRK_NO_MODESEL type and use it for the OnStream real SCSI
device (not the broken one). This one is still broken in that it can't
be set to the same fixed block size it reports [ unflattering comments
about this company elided ].
If we're unable to set buffered mode on, complain, but drive on. It's
not a fatal error to not be in buffered mode.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
Exceptions:
Vinum untouched. This means that it cannot be compiled.
Greg Lehey is on the case.
CCD not converted yet, casts to struct buf (still safe)
atapi-cd casts to struct buf to examine B_PHYS
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
- Mike Smith discovered a panic in the changer probe code if the probe
command (mode sense) fails. So we need to release the CCB used in the
probe before we unlock the peripheral. (i.e. the same fix mjacob put in
the CD and DA drivers)
- A newline was missing in a warning message. (PR kern/17512)
PR: kern/17512
Submitted by: Louis Mamakos <louie@uu.net> (newline fix)
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
an HBA. Garbage in this field confuses the driver in targdone().
o When completing a CCB on behalf of a user process, we need to
*de-queue* the ccb from our pending ccb list, not queue it again.
o All continue target I/O operations need to have a timeout set.
We use 5 seconds throughout this driver.
o Remove some logging printfs.
o During abort processing, remove ccbs that are on the pending queue
from the pending queue, not the work queue.
256 bytes) caused it to break on many devices.
The SCSI spec says that for commands with 8-bit length fields, a value of 0
means 256 bytes. As it turns out, many devices don't deal with that
properly. Some interpret the 0 as 0, and return no data. Others return
more than 256 bytes of data, and cause an overrun.
The fix is to tell the device we've only allocated SHORT_INQUIRY_LENGTH (36
bytes) of inquiry data, instead of sizeof(struct scsi_inquiry_data).
camcontrol.c: Change inq_len in the call to scsi_inquiry() to
SHORT_INQUIRY_LENGTH, and add a long comment
explaining the reason for the change.
scsi_all.h: Add a comment above the definitinon of
SHORT_INQUIRY_LENGTH alerting people that it is
both the initial probe inquiry length, and the
minimum amount of data needed for scsi_print_inquiry()
to function.
scsi_all.c: Add a comment about SHORT_INQUIRY_LENGTH being the
minimum amount of data needed for
scsi_print_inquiry() to function.
Reviewed by: gibbs
Approved by: jkh
Reported by: "John W. DeBoskey" <jwd@unx.sas.com>
that there's sense to send with status (if the SIM does it), and
then clear any pending contingent allegiance state for this initiator
if the SIM actually did send the sense data.
Widen MAX_INITITATORS to 256- that's still not quite right, but will
accomodate the widest Fibre Channel support in FreeBSD now.
Obtained from:(partially) gibbs@freebsd.org
full size. Define a SHORT_INQUIRY_LENGTH for use during initial
probing (covers the size used previously). Define some SPC-2 related
fields (and define the revision code for SPC-2) which includes some
further SPI-3 defines. Don't go all the way (256 bytes) for the structure-
stop 4 bytes short- because we haven't auditted the source base to find
any u_int8_t potential overflow issues. Add RBC (single byte device)
and OCR (Optical Character Reader) device type codes.
Approved by JKH.
Reviewed by: gibbs@freebsd.org, ken@freebsd.org
to be more platform independent. Add a ses_hlptxt structure definition
and retrieval ioctl for when we are able to retrieve object help text
SES Objects can have up to 64 KBytes of associated 'help' text- the
Sun A5000 uses this, for example, to give physical location information
(e.g., 'left power supply').
to be created at init time. The unit devices are created at
ctor when new instances are created and bound and destroyed
when that instance is closed. As such, there is just s single
static control dev_t for this driver (the per-unit dev_t's are
still in the softc).
When we have decommissionable periph drivers, a destroy_device
on the control device will have to called.
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
second LUN to show up.
mjacob's change (which is correct) in rev 1.21 of cam_periph.c to elminiate
infinite retries of the SCSI busy status bit seems to have broken probing
of Pioneer changers that aren't already quirked.
The right way to fix this is probably to change things around so we can
guarantee 100% sequential probing of LUN-based changers even if they aren't
quirked. This should fix things for now, though.
The same goes for CD drivers and tape drivers. In systems with mixed IDE
and SCSI, devices in the same priority class will be sorted in attach
order.
Also, the 'CCD' priority is now the 'ARRAY' priority, and a number of
drivers have been modified to use that priority.
This includes the necessary changes to all drivers, except the ATA drivers.
Soren will modify those separately.
This does not include and does not require any change in the devstat
version number, since no known userland applications use the priority
enumerations.
Reviewed by: msmith, sos, phk, jlemon, mjacob, bde
in samount. Make things a lot quieter in samount (and other places). Fix
ridiculous and not so ridiculous bugs in compression related code in both
sagetparams and sasetparams.
saprevent when we're doing an OFFLINE ioctl- saprevent
won't unlock the door, which then causes the unload to
fail on some units.
If we've already unloaded the tape, don't try and rewind and
unload in saclose. This is a slightly riskier change because
we're now going to depend on SA_FLAG_TAPE_MOUNTED to say whether
we've really unloaded the tape. This involved changing the
setting in sadone for tape errors to SA_FLAG_TAPE_FROZEN (which
is more accurate anyway-if you get an EIO you've probably lost
tape position anyway) where it used to just clear the mounted
flag.
Merge the contents (less some trivial bordering the silly comments)
of <vm/vm_prot.h> and <vm/vm_inherit.h> into <vm/vm.h>. This puts
the #defines for the vm_inherit_t and vm_prot_t types next to their
typedefs.
This paves the road for the commit to follow shortly: change
useracc() to use VM_PROT_{READ|WRITE} rather than B_{READ|WRITE}
as argument.
and add a config option that allows one to default to 1FM@EOD for tapes
otherwise unquirked or unknown as to which to prefer. Note that tcopy
will be broken for these tapes until tcopy is fixed.
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
events, in order to pave the way for removing a number of the ad-hoc
implementations currently in use.
Retire the at_shutdown family of functions and replace them with
new event handler lists.
Rework kern_shutdown.c to take greater advantage of the use of event
handlers.
Reviewed by: green
- increase the default timeout from 10 seconds to 60 seconds
- add a new kernel option, SCSI_PT_DEFAULT_TIMEOUT, that lets users specify
the default timeout for the pt driver to use
- add two new ioctls, one to get the timeout for a given pt device, the
other to set the timeout for a given pt device. The idea is that
userland applications using the device can set the timeout to suit their
purposes. The ioctls are defined in a new header file, sys/ptio.h
PR: 10266
Reviewed by: gibbs, joerg
about a dev_t.
printf("%x", dev) now becomes printf("%s", devtoname(dev)) because
printing actual information about the device is much more useful then
printing a pointer to an address that would never help the developer debug.
Submitted by: phk, bde
Handle errors reported through immediate notify ccbs. This includes
bus resets, BDR messages, and abort messages.
Properly setup CA conditions for errors such as uncorectable parity
in data phases, reselection failure, and IDE message received.
Add a mechanism for stalling the queue of transactions to a particular
initiator while a CA is in progress. Since we don't yet support
tagged I/O, this is largely just for show right now.
Properly bzero our softc at init time (oops).
Add more documentation on what all of the queues in our softc do.
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
zero traps. I actually can't believe that this compiler is *sooooo* stupid
that it did a divide when there was 1024L*1024L instead of a right shift by
20. When we get quad type modifiers in kernel printf we can change to this
too (to avoid overflow on > terabyte disk sizes).
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
