line is > LINE_LEN (512 bytes), we scribble (*blush*).
Hinted at by: Theo de Raadt <deraadt@cvs.openbsd.org>
Change sprintf(buf, "fixedstring") to strcpy(buf, "fixedstring").
all RTF_WASCLONED routes, and the second removes the
others. This avoids the situation where we've added an
RTF_CLONING route (such as ``default''), created some
clones, then deleted the CLONING route before the
WASCLONED route(s). Without the two passes, we get
errno (not rtm_errno) set to ESRCH when deleting the
WASCLONED route, despite the deletion succeeding !
Also:
Enhance the route operation failure diagnostics.
Make portability #ifdefs a bit more generic.
change from
ioctl(fd, PIOC<foo>, &i);
to
ioctl(fd, PIOC<foo>, i);
This is going from the _IOW to _IO ioctl macro. The kernel, procctl, and
truss must be in synch for it all to work (not doing so will get errors about
inappropriate ioctl's, fortunately). Hopefully I didn't forget anything :).
Validate the peers suggested IP by attempting to make a routing table
entry.
Give up IPCP negotiation if the peer NAKs us with an unusable IP.
Always SIOCDIFADDR then SIOCAIFADDR when configuring the tun device.
Using SIOCSIFDSTADDR allows duplicate dst addresses (which we don't
want)!!!
Allow up to 200 interface names (was 50) (now that ppp can play server
properly).
Up the version number (1.5 -> 1.6).
Cosmetic:
Log unexpected CCP packets in the CCP log rather than the ERROR log.
Log unexpected Config Reqs in the appropriate LCP/IPCP/CCP log rather
than the ERROR log.
Log failed route additions and deletions with WARN, not TCPIP.
Log the option id and length for unrecognised IPCP options.
Change some .Sq to .Ar in the man page.
Changed lots of %ld's in format strings back to %d. %ld was right
when daddr_t was long, but Lite2 changed daddr_t to int32_t which
is implemented as `int' on i386's.
We must call inflate again in case there's any pending output
despite our input buffer being empty. If the output buffer
is in fact already flushed, inflate() returns Z_BUF_ERROR.
There isn't really an error !
since we only store CIS_MAXSTR data, and the users may stick the
'entire' CIS string returned from the card in /etc/pccard.conf and
cause the comparison to (bogusly) fail.
Submitted by: Brad Karp <karp@eecs.harvard.edu>
I did the deflate re-org).
Make PAP & CHAP negotiation prettier in the log file.
If both PAP & CHAP are `enabled' and the peer NAKs CHAP
suggesting PAP, be friendly and REQ PAP the next time.
This is in line with the rfc.
protocols to recognized extra buttons and wheel/roller. It now has
PnP COM device support code, thus, some recent mouse products are
automatically detected and an appropriate protocol is selected.
The `-i' option will print the result of auto-detection.
- Added support for the following SERIAL mice:
ALPS GlidePoint, MS IntelliMouse, Kensington Thinking Mouse
(Genius NetMouse, NetMouse Pro, ASCII MieMouse, Logitech MouseMan+,
FirstMouse+ are compatible with MS IntelliMouse, when connected
to a serial port, thus requires no explicit support)
- Added PnP serial mouse identification capability as defined
by Microsoft and Hayes in "Plug and Play External COM Device
Specification, rev 1.00". This support will enable us to identify
the correct protocol to use, or choose a compatible protocol for the
given mouse.
- Utilize new ioctls defined in `mouse.h' to get hardware and protocol
information on PS/2 and bus mouse devices. Try to guess the correct
protocol and port combination based on the obtained info.
- Use MOUSE_SETLEVEL ioctl.
- Use constants defined in `mouse.h' rather than using own definitions.
- A New command line option. The -i option prints the information
collected though the PnP code and psm/mse ioctls mentioned above,
and just quits. This is to test `moused's ability, or inability, to
detect the correct protocol for the given mouse automatically.
- A new command line option. The -m option maps a physical button
to a logical button.
- A new command line option. The -z option maps the Z axis movement to
another axis or a pair of buttons.
- Add other options: -3, -C -F -P.
- Added a handler for SIGHUP. This has been suggested by somebody in the
past (I don't remember who). He wanted this because he wants to attach
or detach a mouse while his laptop is suspended. Now `moused' will
reopens and reinitialize the specified port whenever a SIGHUP is
received. I don't know how useful this can be...
Delete AF_LINK routes as well as AF_INET.
Allow the word `default' as the arg to `delete' or in place of the
first two args (dest & netmask) to `add'.
Accept INTERFACE as the third arg to `add'.
You can now say `add default interface' to create a default route
through the tun interface. It's reported that subsequent bind()s
will bind to a broadcast address and not to the address currently
assigned to the tun device - this is the first step towards
supporting that first connection that was around from before the
dynamic IP negotiation....
instead of htonl() !
This results in the int a,b,c,d changing to b,a,c,d,
but as it's subsequently coerced to a u_short, the
ultimate answer is correct.
If this isn't fixed properly soon (by the author) I'll
have a look at it again.
Noted by: eivind & ari@suutari.iki.fi
(I *really* meant to do this *before* committing the
deflate changes in the first place - oops).
Pppd is horribly broken in this respect - refer to the
ppp man page for details. Ppp *WON'T* negotiate deflate
with pppd by default - you must ``enable'' and ``accept''
``pppd-deflate'' in your config.
While I'm in there, update the cftypes in ccp.c so that
we recognise some more protocols (we don't actually do
anything with them - just send a REJ).
- Get rid of a lot of the static variables which were shared by
many routines and programs in the suite.
- Create an abstract interface to the printcap database, so that
other retrieval and iteration mechanisms could be developed
(e.g., YP, Hesiod, or automatic retrieval from a trusted server).
- Give each capability a human-readable name in addition to the historic
two-character one.
- Otherwise generally clean up a lot of dark corners. Many still remain.
- When submitting jobs, use the official login name record (from getlogin())
if there is one, rather than reverse-mapping the uid.
More to come...
break each ruleset into identified sections. (called groups).
note which groups can be reordered.
each group accepts and returns the same strings,
as much as possible.
reactivate Paul Vixie's RBL (in check_mail)
add rules to limit mail relaying to a list of hosts and domains
in the R class (check_rcpt, not active on hub.freebsd.org)
Submitted by: jmb
instead Do The Right Thing when the kernel states a card was
inserted/removed. This isn't a complete fix, but better than nothing.
Reviewed by: Guido van Rooij <guido@gvr.org>
Remove extraneous decls.
Add ``const'' to several places.
Allow ``make NOALIAS=1'' to remove IP aliasing.
Merge with OpenBSD - only the Makefiles vary.
We can now survive a compile with
-Wall -Wbad-function-cast -Wcast-align -Wcast-qual
-Winline -Wmissing-declarations -Wmissing-prototypes
-Wnested-externs -Wpointer-arith -Wredundant-decls
-Wshadow -Wstrict-prototypes -Wwrite-strings -Wchar-subscripts
(although the Makefile just contains -Wall).
Remove the timeout hack to notice that ppp has closed the connection.
Remove the ``special case'' hacks for "quit" and "bye", as pppctl
now exits immediately when the connection is closed by ppp.
Suggest a secure "set server" line for connecting ppp & pppctl.
Tidy up and correct a few man page typos.
avoids the situation where we specify label ``x'' on the command
line, and label ``x'' has a ``load y'' command embedded in it.
When the line comes up, we want to use ``x'' from ppp.linkup,
not ``y''.
allowing for a possible header on the front of all packets.
In OpenBSD, there's a structure containing the address
family here.
If we're building under OpenBSD, set up the ``flags'' part
of struct tuninfo (not there under FreeBSD) so that we config
the interface as POINTOPOINT.
Prefix prototypes with ``extern'' in os.c for consistency.
These changes are cosmetic under FreeBSD, but allow ppp to
build & work under OpenBSD (bar the srandomdev() stuff,
the inclusing of <net/if_var.h> and some Makefile symantecs).
Print out inteface names rather than numbers, and use the
same "find out the names" code in SetIfAddr(). This means
that the nasty ioctl(,SIOCGIFCONF,)/realloc loop is now
buried :-)
Ever since I first say the way the mount flags were used I've hated the
fact that modes, and events, internal and exported, and short-term
and long term flags are all thrown together. Finally it's annoyed me enough..
This patch to the entire FreeBSD tree adds a second mount flag word
to the mount struct. it is not exported to userspace. I have moved
some of the non exported flags over to this word. this means that we now
have 8 free bits in the mount flags. There are another two that might
well move over, but which I'm not sure about.
The only user visible change would have been in pstat -v, except
that davidg has disabled it anyhow.
I'd still like to move the state flags and the 'command' flags
apart from each other.. e.g. MNT_FORCE really doesn't have the
same semantics as MNT_RDONLY, but that's left for another day.
everything else. Add a "-t" option for outputting it in raw form.
Define and document the order in which raw values are printed when
more than one is requested on the command line.
o Add "allow" command:
"allow users a b c" gives access to users a, b and c.
"allow modes auto" gives those users access to auto mode only.
"allow users *" and "allow modes *" are accepted.
No users and all modes are allowed by default.
UID 0 can do anything.
o Set the current label with the "load" and "dial" commands
so that the call to ppp.linkdown makes sense.
o Up the verison number.
o Don't OR MODE_AUTO for -background and -ddial.
o Don't OR MODE_INTER when we get a diagnostic connection.
o Allow up to 40 args per line (was 20).
o "set ifaddr" only changes the interface in AUTO mode (with other
modes, it happens after IPCP negotiation).
o Sort command descriptions in the man page.
o Support -dedicated mode where we just talk ppp forever (no login etc).
to work on FreeBSD, man page written by me.)
Also change Makefile.yp a little to be more tolerane in the face of
missing source files. Print a message if we can't find /var/yp/master.passwd
telling the user what to do to fix things.
Stay as the invoking uid as much as possible.
Execution as a normal user is still forbidden for now,
so these changes are pretty ineffective.
The next commit will implement the modifications suggested
on -hackers a number of days ago.
ppp.secret to get a key value based on the peers name,
then send the value of AuthName with the encrypted result.
This is *way* too confusing.
Instead, always use AuthName and AuthKey as the documentation
says.
location. Also, instead of jumping ot the CPU's restart vector, just
call int 0x19 to reboot. (Writing hte 0x1234 was a little useless
otherwise.)
PR: bin/4901
Submitted by: Jonathan Mini <mini@d198-232.uoregon.edu>
Use getpwnam before getpwuid since two users with same uids can exists
(affects new login classes code only)
The same fixes as in inetd: by default run `system crontab things' with
daemon login class now, not restrict them to user class breaking
compatibility with old way (so-called nobody limits problem)
Implement user[:group][/login-class] syntax in system crontab
for more flexible control (the same as in inetd)
o Report modem connect time properly
o Report bytes in/out over physical media
o Fix phases (TERMINATE is *higher than* DEAD)
o Do a LayerFinish from LcpDown
o Bring down IPCP & CCP when we enter PHASE_TERMINATE
o Give a new prompt when we go to PHASE_DEAD
o Stop the modem timer properly when idle
o Treat sig 15 like an exiting carrier loss
o Log (DEBUG) offline & online transitions
removed. Add a new state 'suspend' so we 'fake' insertion events at
resume time for the cards that have been suspended.
[
The code still works if you remove the card during suspend, switch the
card during suspend, or combinations of both.
]
Reviewed by: frf@xocolatl.com
candidate for this is "npx0", more are likely to follow.
Check for pseudo-devices that are being configured, but don't appear
in any "files" file. The ``pseudo-device bpf 2'' already hit me too
often.
follow.
* Rename/reorder all of the pccard structures, change many of the member
names to be descriptive, and follow more closely other 'bus' drivers
naming schemes.
* Rename a bunch of parameter and local variable names to be more
consistant in the code.
* Renamed the PCCARD 'crd' device to be the 'card' device
* KNF and make the code consistant where it was obvious.
* ifdef'd out some unused code
o Add missing $Id$s
o Move extern decls from .c -> .h files
o Staticize
o Remove #includes from .h files
o style(9)ify includes
o bcopy -> memcpy
bzero -> memset
bcmp -> memcmp
index -> strchr
rindex -> strrchr
o Move timeout.h -> timer.h (making it consistent w/ timer.c)
o Add -Wmissing-prototypes
before any file names. This change makes pkg_add to process those
packages if @exec/@unexec commands don't contain any %[fFB]. Also
enable @exec/@unexec that have %D if the installation prefix is known to
pkg_add.
Reviewed by: jkh
and the kernel will have a 'config interface version number'. If an
incompatable change is made to the kernel that requires a rebuild of
config(8) (such as the cam devtab stuff), then the version number would be
bumped in both places. If a user neglects to rebuild config, then they
will get a nagging (but non-fatal) warning that they need to rebuild
config.
to find dependent packages on the local disk (i.e. package given as
filename, not URL)
- document $PKG_PATH
- use -v on pkg_add for dependent packages
Submitted by: hubertf@NetBSD.ORG
Obtained from: NetBSD
don't claim that _any_ serial speed is settable, mention that it has to
be supported by the device driver. Some have very flexible baud rate
selection (ie: based on divisors etc, such as the com ports), while others
have explicit baud rate choices.
