<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
(which is actually a CATC Netmate).
Gee. I don't know why people make such a fuss over supporting USB ethernet
NICs. This is easier than collecting graft.
Update the license in the rio_usb.h (now rio500_usb.h) to not be GPL.
Sorry for committing that file in the first place. The change of license
was agreed to by the original author.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
unit numbers all wrong. This did not show up because most of them where
zero anyway.
Use a separate buffer for command transforms instead of fiddling with
the existing cdb_bytes.
Take CAM_CDB_POINTER into account. Nobody is using it, but someone might
in the future.
Be more picky about what to accept in the UFI command set.
First attempt at implementing the ATAPI command protocol transforms.
This should at least make Imation Superdisk and other e-Shuttle based
devices show as attached. Maybe they even work to some extent.
contains the ADMtek Pegasus AN986 USB chipset. The
adapter supports both 10BaseT and 100BaseT (including
full-duplex). The product code for these adapters is
0x2206.
and has not been loaded via a kldload,
running usbd(8) will autoload the "usb.ko" kld.
thanks to Peter Wemm for enlightening me on the
differences between kldfind(2) and modfind(2).
to be based on the transfer speed, but I got it all wrong. The by far
biggest factor in the timeout is the start of a removable device, which
is about 2 seconds anyway.
Prodded by: Lennart Augustsson
This makes it possible to handle the done queue even when the end of tail
TD has ended up on the done queue as well (the xfer in this case is NULL
but the next field is valid, so we simply skip that element.
Make sure we mark all the handled transfers as handled.
Stop using powerhooks. They are a NetBSD-ism.
from panicing when disconnecting a USB Wacom Graphire tablet.
jhk approved the fix some time ago, but I forgot to actually commit the
thing.
Reported by: Dirk van Gulik <dirkx@webweaving.org>
Approved by: jhk
problem was basically (for offset > 4096):
vtophys(addr) + offset != vtophys(addr + offset)
Also, use TD's with a maximum size of 4k instead of 8kb for OHCI
controllers.
This problem occurs in drivers that use large transfer sizes:
umass, host2host and ethernet with jumbo frames.
is initialised by usb_init.
This might solve problems with some controllers not being initiliased
properly, because a delay was effectively a tsleep that returned
immediately.
Approved by: jhk
the PIRQD bit.
This fixes the problem of uhub0 hanging forever during boot when USB
keyboard support is switched on in the BIOS on motherboards with Intel
chipsets (UHCI).
Approved by: The Sheep
bus_delete_resource.
Fixes a problem when the probe succeeded, but the attach failed. The
release of the resources was done inproperly.
Approved by: jkh
Some controllers submit bogus pointers to the Done queue.
ohci_hash_find_td fails to find these in its hash and panics. Instead of
panicing we now assume the whole done queue is lost and let the timeout
code to clean up the mess after us.
uhci_check_intr() routine needs to be more careful about deciding when
the end of a transfer has been detected.
This allows me to remove the nasty workaround code from if_aue and if_cue.
Receive performance is now much better for these adapters (500KB/sec
vs. 350KB/sec).
Also removed unused KUE_CUTOFF define from if_kuereg.h.
Submitted by: Lennart Augustsson
Reviewed by: n_hibma
methods for USB devices.
However: with none of the devices I have here suspend seems to work
properly. This is probably a bug in uhci_power which I still have to
look at.
Prodded and pushed by: Christopher Masto <chris@netmonger.net>
- Sync ohci, uhci and usbdi modules with NetBSD in order to obtain the
following improvements:
o New USBD_NO_TSLEEP flag can be used in place of UQ_NO_TSLEEP
quirk. This allows drivers to specify busy waiting only for
certain transfers (namely control transfers for reading/writing
registers and stuff).
o New USBD_FORCE_SHORT_XFER flag can be used to deal with
devices like the ADMtek Pegasus that sense the end of bulk OUT
transfers in a special way (if a transfer is exactly a multiple
of 64 bytes in size, you need to send an extra empty packet
to terminate the transfer).
o usbd_open_pipe_intr() now accepts an interval argument which
can be used to change the rate at which the interrupt callback
routine is invoked. Specifying USBD_DEFAULT_INTERVAL uses the
value specified in the device's config data, but drivers can
override it if needed.
- Change if_aue to use USBD_FORCE_SHORT_XFER for packet transmissions.
- Change if_aue, if_kue and if_cue to use USBD_NO_TSLEEP for all
control transfers. We no longer force the non-tsleep hack for
bulk transfers since these are done asynchronously anyway.
- Removed quirk entry fiddling from if_aue and if_kue since we don't
need it anymore now that we have the USBD_NO_TSLEEP flag.
- Tweak ulpt, uhid, ums and ukbd drivers to use the new arg to
usbd_open_pipe_intr().
- Add a flag to the softc struct in the ethernet drivers to indicate
when a device has been detached, and use this flag to perform
tests to prevent the drivers from trying to do control transfers
if this is the case. This is necessary because calling if_detach()
with INET6 enabled will eventually result in a call to the driver's
ioctl() routine to delete the multicast groups on the interface,
which will result in attempts to perform control transfers. (It's
possible this also happens even without INET6 support enabled.) This
is pointless since we know that if the detach method has been called,
the hardware has been unplugged.
- Changed watchdog timeout routines to just call the driver init routines
to initialize the device states without trying to close and re-open the
pipes. This is partly because we don't want to frob things at interrupt
context, but also because this doesn't seem to work right and I don't
want to panic the system just because a USB device may have stopped
responding.
- Fix aue_rxeof() to be a little smarter about detecting when a double
transfer is needed. Unfortunately, the design of the chip makes it hard
to get this exactly right. Hopefully, this will go away once either
Nick or Lennart finds the bug in the uhci driver that makes this ugly
hack necessary.
- Also sync usbdevs with NetBSD.
