going to hurt sio(4) performance for the time being. As we get closer to
release and have more of the kernel unlocked we can come back to doing
arcane optimizations to workaround the limitations of the sio hardware.
claimed that their Intel NIC is comatose after a warm boot from Windoze.
This is most likely due to the card getting put in the D3 state. This
should bring it back to life.
PCI code. This saves each driver from having to grovel around looking
for the right registers to twiddle.
I should eventually convert the other PCI drivers to do this; for now,
these three are ones which I know need power state handling.
The fix works by reverting the ordering of free memory so that the
chances of contig_malloc() succeeding increases.
PR: 23291
Submitted by: Andrew Atrens <atrens@nortel.ca>
format version number. (userland programs should not need to be
recompiled when the netgraph kernel internal ABI is changed.
Also fix modules that don;t handle the fact that a caller may not supply
a return message pointer. (benign at the moment because the calling code
checks, but that will change)
require the addition of flag 0x80000 to their config line in
pccard.conf(5). This flag is not optional. These Linksys cards will
not be recognized without it.
Reviewed by: imp, iwasaki
The what argument is the hold type that assertion acts on. LK_SHARED
to assert that the process holds a shared, LK_EXCLUSIVE to assert that
the process holds _either_ a shared lock or an exclusive lock.
this gives us several benefits, including:
* easier extensibility- new optional methods can be added to
ac97/mixer/channel classes without having to fixup every driver.
* forward compatibility for drivers, provided no new mandatory methods are
added.
by ensuring that newly allocated blocks are zerod. The
race can occur even in the case where the write covers
the entire block.
Reported by: Sven Berkvens <sven@berkvens.net>, Marc Olzheim <zlo@zlo.nu>
and had no data available returned 0. Now it returns -1 with errno
set to EWOULDBLOCK (== EAGAIN) as it should. This fix makes the bpf
device usable in threaded programs.
Reviewed by: bde
messages send by routers when they deny our traffic, this causes
a timeout when trying to connect to TCP ports/services on a remote
host, which is blocked by routers or firewalls.
rfc1122 (Requirements for Internet Hosts) section 3.2.2.1 actually
requi re that we treat such a message for a TCP session, that we
treat it like if we had recieved a RST.
quote begin.
A Destination Unreachable message that is received MUST be
reported to the transport layer. The transport layer SHOULD
use the information appropriately; for example, see Sections
4.1.3.3, 4.2.3.9, and 4.2.4 below. A transport protocol
that has its own mechanism for notifying the sender that a
port is unreachable (e.g., TCP, which sends RST segments)
MUST nevertheless accept an ICMP Port Unreachable for the
same purpose.
quote end.
I've written a small extension that implement this, it also create
a sysctl "net.inet.tcp.icmp_admin_prohib_like_rst" to control if
this new behaviour is activated.
When it's activated (set to 1) we'll treat a ICMP administratively
prohibited message (icmp type 3 code 9, 10 and 13) for a TCP
sessions, as if we recived a TCP RST, but only if the TCP session
is in SYN_SENT state.
The reason for only reacting when in SYN_SENT state, is that this
will solve the problem, and at the same time minimize the risk of
this being abused.
I suggest that we enable this new behaviour by default, but it
would be a change of current behaviour, so if people prefer to
leave it disabled by default, at least for now, this would be ok
for me, the attached diff actually have the sysctl set to 0 by
default.
PR: 23086
Submitted by: Jesper Skriver <jesper@skriver.dk>
1. ICMP ECHO and TSTAMP replies are now rate limited.
2. RSTs generated due to packets sent to open and unopen ports
are now limited by seperate counters.
3. Each rate limiting queue now has its own description, as
follows:
Limiting icmp unreach response from 439 to 200 packets per second
Limiting closed port RST response from 283 to 200 packets per second
Limiting open port RST response from 18724 to 200 packets per second
Limiting icmp ping response from 211 to 200 packets per second
Limiting icmp tstamp response from 394 to 200 packets per second
Submitted by: Mike Silbersack <silby@silby.com>
the kernel console. Instead, change logwakeup() to set a flag in the
softc. A callout then wakes up every so often and wakes up any processes
selecting on /dev/log (such as syslogd) if the flag is set. By default
this callout fires 5 times a second, but that can be adjusted by the
sysctl kern.log_wakeups_per_second.
Reviewed by: phk
Add detach routine and turn driver into a module so it can be loaded
and unloaded. Also take a stab at implementing multicast packet
reception so that this NIC will work with IPv6. Promiscuous mode
doesn't seem to work, but I'm not sure why. It works well enough that
I can run dhclient on it and put it on the office network though.
Also ripped out spl stuff and replaced it with mutexes.
This is a driver for the LanMedia/SBE LMC150x E1/T1 family of cards.
The driver currently support unframed E1 (2048kbit/s) and framed
E1 (nx64).
These cards will provision E1/T1 lines for about 1/4 the cost of
a cisco router...
