- Remove code duplication by adding two new functions to execute prepared
queue entry via either mbox or request queue and wait for result.
- Since the new function executing via request queue sleeps any way, make
it sleep also in case of overflows or handle shortages. It should make it
more reliable and less affecting other less flexible request queue users.
- Turn isp_target_put_entry() into not target-specific isp_send_entry().
- Make handling of responses with control handles more universal.
- Move RQSTYPE_RPT_ID_ACQ handling into new function.
- Inline isp_handle_other_response(), becoming trivial after above.
- Clean the list of IOCBs from pre-24xx ones.
Before this change in case of request queue overflow driver just froze the
device queue for 100ms to retry after. It was pretty bad for performance.
This change introduces SIM queue freezing when free space on the request
queue drops below 255 entries (worst case of maximum I/O size S/G list),
checking for a chance to release it on I/O completion. If the queue still
get overflowed somehow, the old mechanism is still in place, just with
delay reduced to 10ms.
With the earlier queue length increase overflows should not happen often,
but it is still easily reachable on synthetic tests.
- Make isp_start() to set all the IOCB fields aside of S/G list, removing
extra information from isp_send_cmd(), now only doing S/G lists and sending.
- Turn DMA setup/free from being card and PCI-specific into OS-specific,
instead add new card-specific method for isp_send_cmd(). Previously this
function was a monster handling all the cards.
- Remove double error code translation.
This removes 288KB (36%) of the driver code and zillions of hacks and
workarounds, making single driver uniformly support several different
generations of hardware interfaces, not counting minor card variations.
After years of the hopeless fight, I don't think it worth to continue
support for hardware obsolete for 15-20 years. Instead much cleaner
now code should allow to move forward toward better locking, multiple
queues and other cool features.
All the remaining Qlogic cards starting from 4Gb 24xx to 32Gb 27xx use
the same hardware/firmware interface with minor incremental improvements,
so it seems to be a good new starting point. Except one PCI-X model all
all of them are PCIe and so still usable in modern systems.
Discussed with: ken, scottl, jpaetzel, imp
Relnotes: yes
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Instead of using GID_FT SNS request to get list of registered FCP ports,
use GID_PT to get list of all Nx_Ports, and then use GFF_ID and/or GFT_ID
requests to find whether they are FCP and target capable.
The problem with old approach is that GID_FT does not report ports without
FC-4 type registered. In particular it was impossible to boot OS from
FreeBSD FC target using QLogic FC BIOS, since one does not register FC-4
type even on new cards and so ignored by old code as incompatible.
As a side bonus this allows initiator to skip pointless logins to other
initiators by fetching that information from SNS instead.
In case some switches do not implement GFF_ID/GFT_ID correctly, add sysctls
to disable that functionality. I handled broken GFF_ID of my Brocade 200E,
but there may be other switches with different bugs.
Linux also uses GID_PT, but GFF_ID is disabled by default there, and GFT_ID
is not supported.
Sponsored by: iXsystems, Inc.
This change fixes DMA resource leak on driver unload. Also it removes
DMA resources allocation for hardcoded number of requests before fetching
the real number from firmware. Also it prepares ground for more flexible
IRQs allocation according to firmware capabilities.
MFC after: 2 weeks
This is cosmetics that simplifies identification of new ports on FC switch.
It would be good to use target name from CTL here instead of hostname, but
it is not passed here through CAM now.
MFC after: 2 weeks
I am not sure why this was split long ago, but I see no reason for it.
At this point this unification just slightly reduces memory usage, but
as next step I plan to reuse shared handle space for other IOCB types.
Hacks to enable target mode there complicated code, while didn't really
work. And for outdated hardware fixing it is not really interesting.
Initiator mode tested with Qlogic 1080 adapter is still working fine.
This change simplifies and unifies port adding/updating for loop and
fabric scanners. It also fixes problems with scanning restarts due to
concurrent port databases changes. It also fixes many cosmetic issues.
Modern cards in most cases operate abstract port handles, that have no
any relation to real loop IDs. Leave loopid used only where it really
goes about local loop IDs.
While there, fix few more cases where LUNs were still printed in decimal.
For the most of chips (except anscient ones) port handlers have no relation
to port IDs. In such situation old code scanning first 125 handlers was
quite naive. Instead of doing that, send to chip single request to get full
list of port handlers available on specific virtual port and scan only them.
Old code had problems with case of several virtual ports enabled, when port
handlers allocated from global address space could easily go above 125.
This change was successfully tested on 23xx, 24xx and 25xx chips in loop
mode with 4 virtual initiator ports, each seing 50 virtual target ports.
Aside from cleaner and more consistent code, this allows ports to be both
target and initiator same time, and easily switch from any role to any.
Sponsored by: iXsystems, Inc.
MISC CHANGES
Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee
eventual delivery of a NOTIFY ACK. This is tons better than just
ignoring the return from isp_notify_ack and hoping for the best.
Clean up the lower level lun enable code to be a bit more sensible.
Fix a botch in isp_endcmd which was messing up the sense data.
Fix notify ack for SRR to use a sensible error code in the case
of a reject.
Clean up and make clear what kind of firmware we've loaded and
what capabilities it has.
-----------
FULL (252 byte) SENSE DATA
In CTIOs for the ISP, there's only a limimted amount of space
to load SENSE DATA for associated CHECK CONDITIONS (24 or 26
bytes). This makes it difficult to send full SENSE DATA that can
be up to 252 bytes.
Implement MODE 2 responses which have us build the FCP Response
in system memory which the ISP will put onto the wire directly.
On the initiator side, the same problem occurs in that a command
status response only has a limited amount of space for SENSE DATA.
This data is supplemented by status continuation responses that
the ISP pushes onto the response queue after the status response.
We now pull them all together so that full sense data can be
returned to the periph driver.
This is supported on 23XX, 24XX and 25XX cards.
This is also preparation for doing >16 byte CDBs.
-----------
FC TAPE
Implement full FC-TAPE on both initiator and target mode side. This
capability is driven by firmware loaded, board type, board NVRAM
settings, or hint configuration options to enable or disable. This
is supported for 23XX, 24XX and 25XX cards.
On the initiator side, we pretty much just have to generate a command
reference number for each command we send out. This is FCP-4 compliant
in that we do this per ITL nexus to generate the allowed 1 thru 255
CRN.
In order to support the target side of FC-TAPE, we now pay attention
to more of the PRLI word 3 parameters which will tell us whether
an initiator wants confirmed responses. While we're at it, we'll
pay attention to the initiator view too and report it.
On sending back CTIOs, we will notice whether the initiator wants
confirmed responses and we'll set up flags to do so.
If a response or data frame is lost the initiator sends us an SRR
(Sequence Retransmit Request) ELS which shows up as an SRR notify
and all outstanding CTIOs are nuked with SRR Received status. The
SRR notify contains the offset that the initiator wants us to restart
the data transfer from or to retransmit the response frame.
If the ISP driver still has the CCB around for which the data segment
or response applies, it will retransmit.
However, we typically don't know about a lost data frame until we
send the FCP Response and the initiator totes up counters for data
moved and notices missing segments. In this case we've already
completed the data CCBs already and sent themn back up to the periph
driver. Because there's no really clean mechanism yet in CAM to
handle this, a hack has been put into place to complete the CTIO
CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA
POINTER extended message in it. The internal ISP target groks this
and ctl(8) will be modified to deal with this as well.
At any rate, the data is retransmitted and an an FCP response is
sent. The whole point here is to successfully complete a command
so that you don't have to depend on ULP (SCSI) to have to recover,
which in the case of tape is not really possible (hence the name
FC-TAPE).
Sponsored by: Spectralogic
MFC after: 1 month
32 bit handles. The RIO (reduced interrupt operation) and fast posting
for the parallel SCSI cards were all 16 bit handles. Furthermore,
target mode parallel SCSI only can have 16 bit handles.
Use part of a supplied patch to switch over to using 32 bit handles.
Be a bit more conservative here and only do this for parallel SCSI
for the 12160 (Ultra3) cards. There were a lot of marginal Ultra2
cards, and, frankly, few are findable now for testing.
Fix the target handle routine to only do 16 bit handles for parallel
SCSI cards. This is okay because the upper sixteen bits of the new
32 bit handles is a sequence number to help protect against duplicate
completions. This would be very unlikely to happen with parallel
SCSI target mode, and wasn't present before, so we're no worse off
than we used to be.
While we're at it, finally split the async mailbox completion handlers
into FC and parallel SCSI functions. This makes it much cleaner and
easier to figure out what is or isn't a legal async mailbox completion
code for different card classes.
PR: kern/144250
Submitted partially by: Charles D
MFC after: 1 week
numbers and handle types in rational way. This will better protect from
(unwittingly) dealing with stale handles/commands.
Fix the watchdog timeout code to better protect itself from mistakes.
If we run an abort on a putatively timed out command, the command
may in fact get completed, so check to make sure the command we're
timing it out is still around. If the abort succeeds, btw, the command
should get returned via a different path.
firmware loading bugs.
Target mode support has received some serious attention to make it
more usable and stable.
Some backward compatible additions to CAM have been made that make
target mode async events easier to deal with have also been put
into place.
Further refinement and better support for NP-IV (N-port Virtualization)
is now in place.
Code for release prior to RELENG_7 has been stripped away for code clarity.
Sponsored by: Copan Systems
Reviewed by: scottl, ken, jung-uk kim
Approved by: re
When the linux port changes were imported which split the
target command list to be separate from the initiator command
list and the handle format changed to encode a type in the handle
the implications to the function isp_handle_index (which only
the NetBSD/OpenBSD/FreeBSD ports use) were overlooked.
The fault is twofold: first, the index into the DMA maps
in isp_pci is wrong because a target command handle with
the type bit left in place caused a bad index (and panic)
into dma map. Secondly, the assumption of the array
of DMA maps in either PCS or SBUS attachment structures is
that there is a linear mapping between handle index and
DMA map index. This can no longer be true if there are
overlapping index spaces for initiator mode and target
mode commands.
These changes bandaid around the problem by forcing us
to not have simultaneous dual roles and doing the appropriate
masking to make sure things are indexed correctly. A longer
term fix is being devloped.
and provied an isp_control entry point so that the outer layers can
do PLOGI/LOGO explicitly. Add MS IOCB support. This completes the cycle
for base support for SMI-S.
gone device timers and zombie state entries. There are tunables
that can be used to select a number of parameters.
loop_down_limit - how long to wait for loop to come back up before
declaring
all devices dead (default 300 seconds)
gone_device_time- how long to wait for a device that has appeared
to leave the loop or fabric to reappear (default 30 seconds)
Internal tunables include (which should be externalized):
quick_boot_time- how long to wait when booting for loop to come up
change_is_bad- whether or not to accept devices with the same
WWNN/WWPN that reappear at a different PortID as being the 'same'
device.
Keen students of some of the subtle issues here will ask how
one can keep devices from being re-accepted at all (the answer
is to set a gone_device_time to zero- that effectively would
be the same thing).
to getting rid u_int for uint and so on).
b) Turn back on 64 bit DAC support. Cheeze it a bit in that we have two
DMA callback functions- one when we have bus_addr_t > 4 bits in width and
the other which should be normal. Even Cheezier in that we turn off setting
up DMA maps to be BUS_SPACE_MAXADDR if we're in ISP_TARGET_MODE. More work
on this in a week or so.
c) Tested under amd64 and 1MB DFLTPHYS, sparc64, i386 (PAE, but insufficient
memory to really test > 4GB). LINT check under amd64.
MFC after: 1 month
