would fail to attach due to unsupported USB revision. It should have
no effect when running on a real hardware.
Reviewed by: imp
Approved by: rwatson (mentor)
Add support to uscanner.c for known-working devices
(the same should be done for uscanner2.c).
Waiting for 7.1 to be released before the merge.
MFC after: 3 weeks
Note that there is no working backend (or at least
that is mentioned in the PR ticket) but the device
is now supported on our end.
PR: 117205
Submitted by: Artem Naluzhnyy <tut at nhamon dot com dot ua>
MFC after: 1 week
o add EHCI_SCFLG_BIGEMMIO flag to force big-endian byte-select to be
set in USBMODE
o split reset work into new public routine ehci_reset so bus shim drivers
can force big-endian byte-select before ehci_init
o add support to byte swap EHCI descriptor contents; the IXP435
has dual-EHCI controllers integral but descriptor contents are
in big-endian format; this support is configured with the
USB_EHCI_BIG_ENDIAN_DESC option and enabled with EHCI_SCFLG_BIGEDESC
o clean up EHCI USBMODE register setup during init; add #defines for
bit values
o split debug support out into a new file and enable use through ddb
o while here remove a bunch of lingering netbsd-isms
Reviewed by: imp
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
- Bugfix: Don't excede static number of ports allowed when iterating
over endpoints within an interface.
- u3g_speeds contains speeds in baud, not bytes per second, so divide
the buffer size by 10.
patch the RX/TX performance becomes about 17~18 Mbps comparing with
the previous whose values were RX 7~8Mbps and TX 13~14Mbps.
- improve AL2230 RF handling in zd1211b
- support AL2230S RF that PV2000 is renamed to AL2230S
- use register ZYD_CR244, ZYD_CR243, ZYD_CR242 when the driver writes
values on RF. This routine is more faster than the original one
- use private TX lock to avoid LOR at zyd_raw_xmit()
- increase TX slots from 1 to 5
- needs to set the channel at IEEE80211_S_AUTH not IEEE80211_S_RUN
- detailed error handling. In previous the next command was sent to the
device even if there was errors
- setting ZYD_MAC_RX_THRESHOLD value should be different between 1211
and 1211b
- only try to stop the device at zyd_init_locked() if the device is
UPed
- do not use MTX_RECURSE
- do not try to grap Giant lock when the channel is changing
- move the device initialization routines from zyd_attach to zyd_init to
give a device full-reset chance to the driver.
- code cleanup at zyd_raw_xmit()
- simplify zyd_attach() routines
- resort functions and clean up variables
- DPRINTF style change.
- style(9)
Reviewed by: sam
src/sys/dev/usb2/core/usbdevs
src/sys/dev/usb2/include/urio2_ioctl.h
src/sys/dev/usb2/storage/ustorage2_fs.h
These files are not used any more.
src/usr.sbin/Makefile
src/etc/mtree/BSD.include.dist
src/include/Makefile
src/lib/Makefile
src/share/man/man7/hier.7
src/share/mk/bsd.libnames.mk
src/etc/mtree/BSD.include.dist
Make "usbconfig" and "libusb20" a part of the default build.
src/sys/dev/usb/rio500_usb.h
src/sys/dev/usb2/storage/urio2.c
Use common include file.
src/sys/dev/usb2/bluetooth/ng_ubt2.c
Make USB bluetooth depend on "ng_hci" module.
src/sys/dev/usb2/controller/ehci2.c
src/sys/dev/usb2/controller/ehci2.h
Patches for Marvell EHCI.
src/sys/dev/usb2/core/usb2_busdma.c
Bugfix for 64-bit platforms. Need to unload the previously loaded DMA
map and some cleanup regarding some corner cases.
src/sys/dev/usb2/core/usb2_core.h
src/sys/dev/usb2/core/usb2_dev.c
src/sys/dev/usb2/core/usb2_dev.h
Bugfix for libusb filesystem interface.
New feature: Add support for filtering device data at the expense of the
userland process.
Add some more comments.
Some minor code styling.
Remove unused function, usb2_fifo_get_data_next().
Fix an issue about "fifo_index" being used instead of "ep_index".
src/sys/dev/usb2/core/usb2_device.c
src/sys/dev/usb2/core/usb2_generic.c
Bugfix for Linux USB compat layer. Do not free non-generic FIFOs when
doing an alternate setting.
Cleanup USB IOCTL and USB reference handling.
Fix a corner case where USB-FS was left initialised after
setting a new configuration or alternate setting.
src/sys/dev/usb2/core/usb2_hub.c
Improvement: Check all USB HUB ports by default at least one time.
src/sys/dev/usb2/core/usb2_request.c
Bugfix: Make sure destination ASCII string is properly zero terminated
in all cases.
Improvement: Skip invalid characters instead of replacing with a dot.
src/sys/dev/usb2/core/usb2_util.c
src/sys/dev/usb2/image/uscanner2.c
Spelling.
src/sys/dev/usb2/include/Makefile
Share "usbdevs" with the old USB stack.
src/sys/dev/usb2/include/usb2_devid.h
src/sys/dev/usb2/include/usb2_devtable.h
Regenerate files.
Alfred: Please fix the RCS tag at the top.
src/sys/dev/usb2/include/usb2_ioctl.h
Fix compilation of "kdump".
src/sys/dev/usb2/serial/ubsa2.c
src/sys/dev/usb2/serial/ugensa2.c
Remove device ID's which will end up in a new 3G driver.
src/sys/dev/usb2/sound/uaudio2.c
Correct a debug printout.
src/sys/dev/usb2/storage/umass2.c
Sync with old USB stack.
src/lib/libusb20/libusb20.3
Add more documentation.
src/lib/libusb20/libusb20.c
Various bugfixes and improvements.
src/usr.sbin/usbconfig/dump.c
src/usr.sbin/usbconfig/usbconfig.c
New commands for dumping strings and doing custom USB requests from
the command line.
Remove keyword requirements from generated files:
"head/sys/dev/usb2/include/usb2_devid.h"
"head/sys/dev/usb2/include/usb2_devtable.h"
the softc is reset a few times during probing.
Print 'changing to modem mode' messages if booting verbose to show the
reason for the time delay. Note: Some devices (Huawei for one) take 20
seconds to appear on the USB bus).
The same (vendor, product) tuple is used for aue(4) adapters,
but I am not sure if the quirk is correct. I'm using the USB
device 'release' info to skip aue(4) detection right now, but
if there's a better way to differentiate between USB-LAN and
USB Bluetooth we should update the quirk.
Reviewed by: imp, rink
MFC after: 2 weeks
Also: Change the initialisation of the command string to a static
initialiser. Verify it against the output of umass.c when being sent a
command using 'camcontrol eject da0' to a Bulk-Only device.
This should make those devices work that need a SCSI eject command to
switch to modem mode (Novatel 950D and others).
driver (rev 1.3), by Joerg Sonnenberger.
Note: This change is untested as I do not own the hardware. Let me know
if things work or do not work for you by sending me the output dmesg (and
usbctl -f /dev/usbX if possible). Thanks.
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
might make Qualcomm and Option cards (which have all endpoints in 1
interface) work.
- Change the USB buffer sizes to depend on the transfer speed. With UMTS
we use a buffer 384k / 1000 frames/sec * 50msecs =~ 15kB for example.
- Add a MODULE_VERSION statement
