if option CY_PCI_FASTINTR is configured and mapping the irq to a
fastintr is possible. Unfortunately, this has to be optional because
pci_map_int_right() doesn't handle the INTR_EXCL flag right --
INTR_EXCL is honoured even if the interrupt needs to be non-exclusive
for other devices to work.
register for the PLX id). Merge the vendor's modification of the 2.2.*
release version into -current for reference. Will be cleaned up in next
commit.
Obtained from: ftp://ftp.cyclades.com/pub/cyclades/cyclom-y/freebsd/3.0/cyy30.tar.gz
in cyopen() were done in a different order than in sioopen(), partly
to (ab)use a side effect of comparam() and partly because I didn't
understand what the reset was doing (it flushes the fifos). This
turned out to be more than a cosmetic problem. Flushing the fifos
quite late is good for discarding input that arrived while the line
state was being initialized, and in the cy driver it also seems to
reduce a problem with input that arrived long ago during the previous
close (the UART loses sync too easily and for too long).
The optimisation of only waiting before issuing new commands is
obviously invalid in general and it caused many errors in NIST-PCTS.
I think the errors were mostly for characters sent with the wrong
parity, etc., after a half complete tcsetattr().
Use microtime() instead of a magic loop count to limit the wait.
The wait is a busy-wait :-( and normally takes about 500 usec.
almost works properly. Unfortunately, there is no way to flush
the rx fifo without resetting the channel, which also flushes the
tx fifo. We avoid resetting even when both fifos need to be flushed,
since resetting seems to cause the rx to lose sync if it is done
while data is arriving.
Reminded by: NIST-PCTS
hardware is interrupt-driven to a fault and sending a BREAK requires
mode switching. Always running in the BREAK-capable mode as in PR 8318
would double the overhead for sending \0's.
Reminded by: PR 8318
is completely empty. There is an interrupt for output completion. It
is painful to use, but polling method used in the corresponding fix in
sio.c (rev.1.152) can't be used because there is no status bit for
transmitter-empty. Now ttywait() works right.
Reminded by: NIST-PCTS
Don't call timeout() for DTR wakeup if the relevant timeout is already
active. This fixes "timeout table full" panics when sufficiently many
cyopen()s are interrupted while they are sleeping waiting for the
timeout to expire.
were half of their physical offsets for ISA and 1/4 of their physical
offsets for PCI, while all other Cyclades offsets were physical/1 for
ISA and physical/2 for PCI. Logically wrong macros were used to scale
CY16_RESET and CY_CLEAR_INTR to the correct physical offsets.
Fixed some style bugs (mostly long lines).
interrupt handlers. Instead, load and use it atomically as necessary.
This reduces mode switching overhead for "polled" mode interrupt handling
from 5 i/o's to 3 (per service type, per port) so that polled mode is only
slightly more inefficient than "interrupt" mode.
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
of invariants to cyattach().
Fixed minor bugs:
- cyparam() returned without restoring the ipl in the error cases. This
was harmless because cyparam() is always called at spltty().
- one check for "rev. J or higher" actually checked for precisely rev. J.
swapped RTS/DTR). Merge the vendor's modification of the 2.2.6-release
version into -current for reference. Will be cleaned up in next commit.
Obtained from: ftp://ftp.cyclades.com/pub/cyclades/cyclom-y/freebsd/2.2.6/cyy226.tar.gz
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
FreeBSD/alpha. The most significant item is to change the command
argument to ioctl functions from int to u_long. This change brings us
inline with various other BSD versions. Driver writers may like to
use (__FreeBSD_version == 300003) to detect this change.
The prototype FreeBSD/alpha machdep will follow in a couple of days
time.
The differences Terrys patch and this patch are:
* Remove a lot of un-needed comments.
* Don't put l_hotchar at the front of stuct linesw, there is no need to.
* Use the #defines for the hotchar in the SLIP and PPP line disciplines
This introduce an xxxFS_BOOT for each of the rootable filesystems.
(Presently not required, but encouraged to allow a smooth move of option *FS
to opt_dontuse.h later.)
LFS is temporarily disabled, and will be re-enabled tomorrow.
actually offsets, they are offsets scaled by dividing by 2^cy_align.
I use different values for cy_align since the -current values are
unnaturally scaled, so I need different offsets, and the wrong
offsets got committed.
Reported by: nnd@itfs.nsk.su (N.Dudorov)
Add a simplelock to deal with disable_intr()/enable_intr() as used in UP kernel.
UP kernel expects that this is enough to guarantee exclusive access to
regions of code bracketed by these 2 functions.
Add a simplelock to bracket clock accesses in clock.c: clock_lock.
Help from: Bruce Evans <bde@zeta.org.au>
I have no way of testing this one, first SMP/cy user please let me know...
It is my belief that sio and cy are the only FAST_INTR() ISRs. If this
is a bad assumption please educate me.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
