Commit Graph

9 Commits

Author SHA1 Message Date
Alexander Motin
6a5d28b93a Improve output for controllers that doesn't report SATA speed. 2010-02-22 10:45:40 +00:00
Alexander Motin
066f913a94 MFp4:
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.

As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.

Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.

Submitted by:	nwitehorn (powerpc part)
2009-12-06 00:10:13 +00:00
Alexander Motin
ebbb35ba70 MFp4:
- Remove most of direct relations between ATA(4) peripherial and controller
levels. It makes logic more transparent and is a mandatory step to wrap
ATA(4) controller level into ATA-native CAM SIM.
- Tune AHCI and SATA2 SiI drivers memory allocation a bit to allow bigger
I/O transaction sizes without additional cost.
2009-10-31 13:24:14 +00:00
Rafal Jaworowski
93588d5c28 Move non-PCI prototypes from ata-pci.h -> ata-all.h.
This removes unnecessary PCI #includes dependency for systems with ATA
controllers living at non-PCI buses.

Submitted by:	Piotr Ziecik
Obtained from:	Semihalf
2009-06-24 15:38:17 +00:00
Alexander Motin
4c10f2e605 Add experimental support for SATA interface power management.
Feature is controlled by hint.ata.X.pm_level tunable:
 0 - PM disabled, old behaviour, default.
 1 - device is allowed to initiate PM state change, host is passive.
 2 - host initiates PARTIAL state transition every time port is idle.
 3 - host initiates SLUMBER state transition every time port is idle.

PARTIAL state has up to 100us (50us for me) wakeup latency, but for my
ICH8M saves 0.5W of power per drive. SLUMBER state has up to 10ms (3.5ms
for me) wakeup latency, but saves 0.8W of power.

Modes 2 and 3 are implemented only for AHCI driver now.

Interface power management is incompatible with device presence detection
(host receives no signal from drive, so unable to monitor it), so later is
disabled when PM is used.
2009-04-29 21:17:18 +00:00
Alexander Motin
9cf4fe2ebe Integrate user/mav/ata branch:
Add ch_suspend/ch_resume methods for PCI controllers and implement them
for AHCI. Refactor AHCI channel initialization according to it.

Fix Port Multipliers operation. It is far from perfect yet, but works now.
Tested with JMicron JMB363 AHCI + SiI 3726 PMP pair.
Previous version was also tested with SiI 4726 PMP.

Hardware sponsored by: Vitsch Electronics / VEHosting.nl
2009-03-30 22:18:38 +00:00
Alexander Motin
e412a8c3b5 Use only higher half of device signature to identify device type. Some
devices return incorrect values in lower part confusing detection, while
higher part itself gives enough information for proper detetion.
2009-02-21 23:46:34 +00:00
Alexander Motin
6030a3f04c Improve ata_reinit():
- protect againtst recursions,
 - add new devices detection using ata_identify().

Improve ata_identify():
 - do not add duplicate device if device already exist.

Rework SATA hot-plug events handling. Instead of unsafe duplicate
implementation use common ata_reinit() to handle all state changes.

All together this gives quite stable and robust cold- and hot-plug operation,
invariant to false, lost and duplicate events.
2009-02-21 22:57:26 +00:00
Søren Schmidt
13014ca04a This is the roumored ATA modulerisation works, and it needs a little explanation.
If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.

However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:

atacore:	ATA core functionality, always needed for any ATA setup

atacard:	CARDBUS support
atacbus:	PC98 cbus support
ataisa:		ISA bus support
atapci:		PCI bus support only generic chipset support.

ataahci:	AHCI support, also pulled in by some vendor modules.

ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia;	Vendor support, ie atavia for VIA chipsets

atadisk:	ATA disk driver
ataraid:	ATA softraid driver

atapicd:	ATAPI cd/dvd driver
atapifd:	ATAPI floppy/flashdisk driver
atapist:	ATAPI tape driver

atausb:		ATA<>USB bridge
atapicam:	ATA<>CAM bridge

This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:

device          atacore
device          atapci
device          atavia

And then you need the atadisk, atapicd etc lines in there just as usual.

If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.
2008-10-09 12:56:57 +00:00