ETHERTYPE_IPV6 frames. Change this to be a sysctl knob so that is able to still
bridge non-IP packets if desired.
Also return early if all pfil_* sysctls are turned off, the user obviously does
not want to filter on the bridge.
interfaces to bridges, which will then send and receive IP protocol 97 packets.
Packets are Ethernet frames with an EtherIP header prepended.
Obtained from: NetBSD
MFC after: 2 weeks
case if memory allocation failed.
- Remove fourth argument from VLAN_INPUT_TAG(), that was used
incorrectly in almost all drivers. Indicate failure with
mbuf value of NULL.
In collaboration with: yongari, ru, sam
span ports when they disappear. The span port does not have a pointer to the
softc so revert r1.31 and bring back the softc linked-list.
MFC after: 2 weeks
Use the following kernel configuration option to enable:
options BPF_JITTER
If you want to use bpf_filter() instead (e. g., debugging), do:
sysctl net.bpf.jitter.enable=0
to turn it off.
Currently BIOCSETWF and bpf_mtap2() are unsupported, and bpf_mtap() is
partially supported because 1) no need, 2) avoid expensive m_copydata(9).
Obtained from: WinPcap 3.1 (for i386)
- In ifc_name2unit(), disallow leading zeroes in a unit.
Exploit: ifconfig lo01 create
- In ifc_name2unit(), properly handle overflows. Otherwise,
either of two local panic()'s can occur, either because
no interface with such a name could be found after it was
successfully created, or because the code will bogusly
assume that it's a wildcard (unit < 0 due to overflow).
Exploit: ifconfig lo<overflowed_integer> create
- Previous revision made the following sequence trigger
a KASSERT() failure in queue(3):
Exploit: ifconfig lo0 destroy; ifconfig lo0 destroy
This is because IFC_IFLIST_REMOVE() is always called
before ifc->ifc_destroy() has been run, not accounting
for the fact that the latter can fail and leave the
interface operating (like is the case for "lo0").
So we ended up calling LIST_REMOVE() twice. We cannot
defer IFC_IFLIST_REMOVE() until after a call to
ifc->ifc_destroy() because the ifnet may have been
removed and its memory has been freed, so recover from
this by re-inserting the ifnet in the cloned interfaces
list if ifc->ifc_destroy() indicates a failure.
If the packet is rejected from pfil(9) then continue the loop rather than
returning, this means that we can still try to send it out the remaining
interfaces but more importantly the mbuf is freed and refcount decremented on
exit.
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
copy of Ethernet address.
- Change iso88025_ifattach() and fddi_ifattach() to accept MAC
address as an argument, similar to ether_ifattach(), to make
this work.
softc lists and associated mutex are now unused so these have been removed.
Calling if_clone_detach() will now destroy all the cloned interfaces for the
driver and in most cases is all thats needed to unload.
Idea by: brooks
Reviewed by: brooks
Having an additional MT_HEADER mbuf type is superfluous and redundant
as nothing depends on it. It only adds a layer of confusion. The
distinction between header mbuf's and data mbuf's is solely done
through the m->m_flags M_PKTHDR flag.
Non-native code is not changed in this commit. For compatibility
MT_HEADER is mapped to MT_DATA.
Sponsored by: TCP/IP Optimization Fundraise 2005
promisc flag from the member interface, this is a no-op anyway since the
interface is disappearing. The driver may have already released
its resources such as miibus and this is likely to panic the kernel.
Submitted and tested by: Wojciech A. Koszek
MFC after: 2 weeks
OR the flags bits with the driver managed status flags. This fixes an
issue where RUNNING flags would not be reported to processes, which
conflicts with the flags information provided by ifconfig(8).
that the following funtions are not used, wrap in '#ifdef noused' for the
moment.
bstp_enable_change_detection
bstp_disable_change_detection
bstp_set_bridge_priority
bstp_set_port_priority
bstp_set_path_cost
- move the function pointer definitions to if_bridgevar.h
- move most of the logic to the new BRIDGE_INPUT and BRIDGE_OUTPUT macros
- remove unneeded functions from if_bridgevar.h and sort a little.
Use bridge_ifdetach() to notify the bridge that a member has been detached. The
bridge can then remove it from its interface list and not try to send out via a
dead pointer.
cloner. This ensures that ifc->ifc_units is not prematurely freed in
if_clone_detach() before the clones are destroyed, resulting in memory modified
after free. This could be triggered with if_vlan.
Assert that all cloners have been destroyed when freeing the memory.
Change all simple cloners to destroy their clones with ifc_simple_destroy() on
module unload so the reference count is properly updated. This also cleans up
the interface destroy routines and allows future optimisation.
Discussed with: brooks, pjd, -current
Reviewed by: brooks
http://lists.freebsd.org/pipermail/cvs-src/2004-October/033496.html
The same problem applies to if_bridge(4), too.
- Copy-and-paste the if_bridge(4) related block from
if_ethersubr.c to ng_ether.c
- Add XXXs, so that copy-and-paste would be noticed by
any future editors of this code.
- Also add XXXs near if_bridge(4) declarations.
Silence from: thompsa
module name to something that wouldn't conflict with
sys/dev/firewire/firewire.c.
Submitted by: Cai, Quanqing <caiquanqing at gmail dot com>
PR: kern/82727
MFC after: 3 days
opt_device_polling.h
- Include opt_device_polling.h into appropriate files.
- Embrace with HAVE_KERNEL_OPTION_HEADERS the include in the files that
can be compiled as loadable modules.
Reviewed by: bde
