initialize a TSC timecounter until we know if it is broke or not.
XXX I think there is a bug in the i386 code here. init_TSC_tc() comes
after:
if (statclock_disable)
return;
ie: if you turn off the statclock interrupt, you dont get the TSC either.
for breakpoint and trace traps from usermode. Although all the setidt
entries are interrupt gates on amd64, all but the trace and bpt trap
entry handlers reenable interrupts after the swapgs instruction in order
to simulate the trap/interrupt gate distinction. In other words, the
amd64 code behaves the same way that i386 does here.
for ddb input in some atkbd-based console drivers. ddb must not use any
normal locks but DELAY() normally calls getit() which needs clock_lock.
This also removes the need for recursion on clock_lock.
known constants at compile time rather than at run time. We have a number
of nasty hacks around the place to cache ntohl() of constants (eg: nfs).
This change allows the compiler to compile-time evaluate ntohl(1) as
0x01000000 rather than having to emit assembler code to do it. This
has other smaller flow-on effects because the compiler can see that
ntohl(constant) itself has a constant value now and can propagate the
compile time evaluation.
Obtained from: Ideas from NetBSD and Linux, and some code from NetBSD
1.186: onoe; Sony's PEGA-WL110 CF WLAN (which strangely has fujitsu's
vendor id)
1.185: ichiro; Quatech Inc, PCMCIA Enhanced Parallel Port Card
Also:
o update $NetBSD$
o minor tweaks to FUJITSU. We've tried to keep the CIS only entries seprate
from vendor id/product id.
freed belong to the kernel object.)
- Increase the granularity of the vm object locking in vm_hold_load_pages()
in order to reduce the number of times that we acquire and release the
same lock.
Fix to the messages output under CAM_DEBUG_CCB: the summary sense
information (error bits and sense key) is in the error field, not
in the result field, of struct ata_request. No other functional change.
completion of recovery is indicated by positioning the CAM_AUTOSNS_VALID
bit in the status field of the CCB, not in the flags field.
This fixes an endless loop of sense recovery actions.
Reviewed by: ken
function, startup_alloc(), that is used for single page allocations prior
to the VM starting up. If it is used after the VM startups up, it
replaces the zone's allocf pointer with either page_alloc() or
uma_small_alloc() where appropriate.
Pointy hat to: me
Tested by: phk/amd64, me/x86
Temporarily disable the UMA_MD_SMALL_ALLOC stuff since recent commits
break sparc64, amd64, ia64 and alpha. It appears only i386 and maybe
powerpc were not broken.
device to access 64-bit addresses from a 32-bit PCI bus. While the
RealTek manual says you can set this bit and the chip will perform
DAC only if you give it a DMA address with any of the upper 32
bits set, this appears not to be the case. If I turn on the DAC
bit, the chip sets the 'system error' bit in the status register
when I to do a DMA on my Athlon test box with 32-bit PCI bus (VIA
chipset) even though I only have 128MB of physical memory, and thus
can never give the chip a 64-bit address.
Obviously, I can't just set it and forget it, so until I figure
out the right rule for when it's safe/necessary to enable it, keep
it turned off.
not guaranteed that the RSE writes the NaT collection immediately,
sort of atomically, to the backing store when it writes the register
immediately prior to the NaT collection point. This means that we
cannot assume that the low 9 bits of the backingstore pointer do not
point to the NaT collection. This is rather a surprise and I don't
know at this time if it's a bug in the Merced or that it's actually
a valid condition of the architecture. A quick scan over the sources
does not indicate that we depend on the false assumption elsewhere,
but it's something to keep in mind.
The fix is to write the saved contents of the ar.rnat register to
the backingstore prior to entering the loop that copies the dirty
registers from the kernel stack to the user stack.
