If the client requests that the error recovery code retry a selection
timeout, it will be retried after half a second. The delay is to give the
device time to recover.
For most of these drivers, I only added selection timeout retries where
they were also retrying unit attention type errors. The sa(4) driver calls
saerror() in a number of places, but most of them don't request retrying
unit attentions.
Also, bump the default minimum CD changer timeout from 2 to 5 seconds and
the maximum timeout from 10 to 15 seconds. Some Pioneer changers seem to
have trouble with the shorter timeout.
Reviewed by: gibbs
- first program lock a region in a file,
- second program wait on the lock,
- first program extend the region,
- second program interrupted by a signal.
and ISA DMA channels (ie: on most PCI systems, they are not.. they are
on the ISA side of the PCI-ISA bridge and could be duplicated if there
were multiple PCI-ISA bridges, say in a laptop docking station), while
the APIC resources would be global on SMP systems.
Also, revert a previous change, change some printfs back to panics.
that big a deal just yet and isn't worth a whole line on the boot screen.
This could change later in the face of multi-ISA-bus (eg: laptop docking
stations with two independent ISA busses) and SMP/APIC systems. The Alpha
already has multiple interrupt destinations to deal with.
development that leads to lots of crashes during boot.
I have made a 'reinstall' target (like in ports, and reinstall.debug)
This is most useful if you want to keep /kernel.old as a known bootable
kernel. If you test a new kernel and have to reboot for a fix, a
'make reinstall' will install the new kernel over the top of the old
non-viable one, leaving the old one untouched. This is mainly meant
for development, not general users.
Change haveseen_isadev() to something a little easier to emulate.
Store the device_t for the wrapper in isa_device.
Implement a replacement for haveseen_isadev - namely haveseen_ioport()
which takes a port size as an extra argument for a proper range check.
This (haveseen_ioport()) has not been tested, but I think it'll work.
new isa drivers with sensitive flags. If the resource_find() code
is meant to "find" the wildcard sensitive flag for a driver even though
a unit is supplied, this can be simplified.
Restore 0x710110b9 ("AcerLabs M15x3 Power Management Unit") - but only
if NALPM == 0.
Restore 0x00051166 ("Ross (?) host to PCI bridge") so that
fixbushigh_Ross() gets called.
Delete generic_pci_bridge(), it's been replaced by other mechanisms (see
the isab and pcib match/probes and the pci_bridge_type() function)
o fix DDB support
- include "opt_ddb.h"
- fix Debugger() arg
pointed out by bde
o back out pvc shadow interface support
- it is currently not used
- to make it easier to merge another implementation
o misc minor cleanup
particularly annoying hack, namely having the linker bash the moduledata
to set the container pointer, preventing it being const. In the process,
a stack of warnings were fixed and will probably allow a revisit of the
const C_SYSINIT() changes. This explicitly registers modules in files or
preload areas with the module system first, and let them initialize via
SYSINIT/DECLARE_MODULE later in their SI_ORDER_xxx order. The kludge of
finding the containing file is no longer needed since the registration
of modules onto the modules list is done in the context of initializing
the linker file.
sysinits, for example, are sorted by swapping those objects(!). Perhaps
they should be const and the sysinit sorting should be swapping the
pointers rather than the targets. This is on my revisit list, but it
has the side effect of removing a lot of warnings. With -Wcast-qual, it
doesn't seem easy to get rid of the constness when you *know* it's not.
(With apologies to bde, this essentially reverts rev 1.21 of kernel.h
from back in 1996)
Made a new (inline) function devsw(dev_t dev) and substituted it.
Changed to the BDEV variant to this format as well: bdevsw(dev_t dev)
DEVFS will eventually benefit from this change too.
Virtualize bdevsw[] from cdevsw. bdevsw() is now an (inline)
function.
Join CDEV_MODULE and BDEV_MODULE to DEV_MODULE (please pay attention
to the order of the cmaj/bmaj arguments!)
Join CDEV_DRIVER_MODULE and BDEV_DRIVER_MODULE to DEV_DRIVER_MODULE
(ditto!)
(Next step will be to convert all bdev dev_t's to cdev dev_t's
before they get to do any damage^H^H^H^H^H^Hwork in the kernel.)
Mark the GDB port in the config file with flags 0x80. Currently
only the sio driver checks these flags and sets up a GDB port,
but adding similar code to other serial drivers would be easy.
For backward compatibility, if an sio port is marked as the console
and no port is marked as the gdb port, the GDB port will be mapped
to the console port. This hack should go away at some point.
power management. This will only work on newer firmware revisions; older
firmware will silently ignore the attempts to turn power management on.
Patches supplied by: Brad Karp <karp@eecs.harvard.edu>
files at once on a filesystem running soft updates. The root of
the problem is that soft updates limits the amount of memory that
may be allocated to dependency structures so as to avoid hogging
kernel memory. The original algorithm just waited for the disk I/O
to catch up and reduce the number of dependencies. This new code
takes a much more aggressive approach. Basically there are two
resources that routinely hit the limit. Inode dependencies during
periods with a high file creation rate and file and block removal
dependencies during periods with a high file removal rate. I have
attacked these problems from two fronts. When the inode dependency
limits are reached, I pick a random inode dependency, UFS_UPDATE
it together with all the other dirty inodes contained within its
disk block and then write that disk block. This trick usually
clears 5-50 inode dependencies in a single disk I/O. For block and
file removal dependencies, I pick a random directory page that has
at least one remove pending and VOP_FSYNC its directory. That
releases all its removal dependencies to the work queue. To further
hasten things along, I also immediately start the work queue process
rather than waiting for its next one second scheduled run.
NOTE: These changes will require recompilation of any userland
applications, like cdrecord, xmcd, etc., that use the CAM passthrough
interface. A make world is recommended.
camcontrol.[c8]:
- We now support two new commands, "tags" and "negotiate".
- The tags commands allows users to view the number of tagged
openings for a device as well as a number of other related
parameters, and it allows users to set tagged openings for
a device.
- The negotiate command allows users to enable and disable
disconnection and tagged queueing, set sync rates, offsets
and bus width. Note that not all of those features are
available for all controllers. Only the adv, ahc, and ncr
drivers fully support all of the features at this point.
Some cards do not allow the setting of sync rates, offsets and
the like, and some of the drivers don't have any facilities to
do so. Some drivers, like the adw driver, only support enabling
or disabling sync negotiation, but do not support setting sync
rates.
- new description in the camcontrol man page of how to format a disk
- cleanup of the camcontrol inquiry command
- add support in the 'devlist' command for skipping unconfigured devices if
-v was not specified on the command line.
- make use of the new base_transfer_speed in the path inquiry CCB.
- fix CCB bzero cases
cam_xpt.c, cam_sim.[ch], cam_ccb.h:
- new flags on many CCB function codes to designate whether they're
non-immediate, use a user-supplied CCB, and can only be passed from
userland programs via the xpt device. Use these flags in the transport
layer and pass driver to categorize CCBs.
- new flag in the transport layer device matching code for device nodes
that indicates whether a device is unconfigured
- bump the CAM version from 0x10 to 0x11
- Change the CAM ioctls to use the version as their group code, so we can
force users to recompile code even when the CCB size doesn't change.
- add + fill in a new value in the path inquiry CCB, base_transfer_speed.
Remove a corresponding field from the cam_sim structure, and add code to
every SIM to set this field to the proper value.
- Fix the set transfer settings code in the transport layer.
scsi_cd.c:
- make some variables volatile instead of just casting them in various
places
- fix a race condition in the changer code
- attach unless we get a "logical unit not supported" error. This should
fix all of the cases where people have devices that return weird errors
when they don't have media in the drive.
scsi_da.c:
- attach unless we get a "logical unit not supported" error
scsi_pass.c:
- for immediate CCBs, just malloc a CCB to send the user request in. This
gets rid of the 'held' count problem in camcontrol tags.
scsi_pass.h:
- change the CAM ioctls to use the CAM version as their group code.
adv driver:
- Allow changing the sync rate and offset separately.
adw driver
- Allow changing the sync rate and offset separately.
aha driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
ahc driver:
- Allow setting offset and sync rate separately
bt driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
NCR driver:
- Fix the ultra/ultra 2 negotiation bug
- allow setting both the sync rate and offset separately
Other HBA drivers:
- Put code in to set the base_transfer_speed field for
XPT_GET_TRAN_SETTINGS CCBs.
Reviewed by: gibbs, mjacob (isp), imp (aha)
