assumptions about the state of the cooling devices. Instead, switch them
off on init and, only after that, we are in TZ_ACTIVE_NONE.
Submited by: Andriy Gapon <avg at icyb.net.ua>
Reviewed by: njl
different "platforms" on x86 machines. The existing code already handles
having two platforms: ACPI and legacy. However, the existing approach was
rather hardcoded and difficult to extend. These changes take the approach
that each x86 hardware platform should provide its own nexus(4) driver (it
can inherit most of its behavior from the default legacy nexus(4) driver)
which is responsible for probing for the platform and performing
appropriate platform-specific setup during attach (such as adding a
platform-specific bus device). This does mean changing the x86 platform
busses to no longer use an identify routine for probing, but to move that
logic into their matching nexus(4) driver instead.
- Make the default nexus(4) driver in nexus.c on i386 and amd64 handle the
legacy platform. It's probe routine now returns BUS_PROBE_GENERIC so it
can be overriden.
- Expose a nexus_init_resources() routine which initializes the various
resource managers so that subclassed nexus(4) drivers can invoke it from
their attach routine.
- The legacy nexus(4) driver explicitly adds a legacy0 device in its
attach routine.
- The ACPI driver no longer contains an new-bus identify method. Instead
it exposes a public function (acpi_identify()) which is a probe routine
that the MD nexus(4) drivers can use to probe for ACPI. All of the
probe logic in acpi_probe() is now moved into acpi_identify() and
acpi_probe() is just a stub.
- On i386 and amd64, an ACPI-specific nexus(4) driver checks for ACPI via
acpi_identify() and claims the nexus0 device if the probe succeeds. It
then explicitly adds an acpi0 device in its attach routine.
- The legacy(4) driver no longer knows anything about the acpi0 device.
- On ia64 if acpi_identify() fails you basically end up with no devices.
This matches the previous behavior where the old acpi_identify() would
fail to add an acpi0 device again leaving you with no devices.
Discussed with: imp
Silence on: arch@
the cpufreq drivers to reliably use properties of PCI devices for quirks,
etc.
- For the legacy drivers, add CPU devices via an identify routine in the
CPU driver itself rather than in the legacy driver's attach routine.
- Add CPU devices after Host-PCI bridges in the acpi bus driver.
- Change the ichss(4) driver to use pci_find_bsf() to locate the ICH and
check its device ID rather than having a bogus PCI attachment that only
checked for the ID in probe and always failed. As a side effect, you
can now kldload ichss after boot.
- Fix the ichss(4) driver to use the correct device_t for the ICH (and not
for ichss0) when doing PCI config space operations to enable SpeedStep.
MFC after: 2 weeks
Reviewed by: njl, Andriy Gapon avg of icyb.net.ua
the appropriate bit in the DEVACTB register.
This change allows the C2 state on those systems to work as expected.
Reviewed by: njl
Submitted by: Andriy Gapon <avg at icyb.net.ua>
MFC after: 1 week
spec:
- Use read/modify/write cycles to enable and disable the HPET instead of
writing 0 to reserved bits.
- Shutdown the HPET during suspend as encouraged by the spec.
- Fail to attach to an HPET with a period of zero.
MFC after: 1 week
PR: kern/119675 [3]
Reported by: Leo Bicknell | bicknell ufp.org
zone code. The GPE handler method (i.e. _L00) generates various Notify
events that need to be run to completion before the GPE is re-enabled.
In ACPI-CA, we queue an asynch callback at the same priority as a Notify
so that it will only run after all Notify handlers have completed. The
callback re-enables the GPE afterwards. We also changed the priority of
Notifies to be the same as GPEs, given the possibility that another GPE
could arrive before the Notifies have completed and we don't want it to
get queued ahead of the rest.
The ACPI-CA change was submitted by Alexey Starikovskiy (SUSE) and will
appear in a later release. Special thanks to him for helping track this
bug down.
MFC after: 1 week
Tested by: jhb, Yousif Hassan <yousif / alumni.jmu.edu>
correct number of acpi_thermalX devices. Having this wrong caused the
acpi_thermal thread to realloc the array of devices on each loop iteration.
MFC after: 1 week
PR: kern/118497
Submitted by: Pasi Parviainen
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
CPUs to make sure idle threads are evicted from the softc before returning
from acpi_cpu_shutdown(). However, this is unnecessary since stop_cpus()
handles this for itself and at this point it's possible that our IPI will be
blocked (interrupts disabled).
Thanks to: Glen Leeder <glen.leeder / nokia.com>
MFC after: 3 days
reason (not all BIOSen have _DIS methods for all link devices for example).
This matches the behavior of attach() with respect to _DIS as well.
Submitted by: njl
handle to the PCI device_t if the ACPI device_t is already attached to a
driver. This happens on the Tablet TC1000 which for some reason includes
two PCI-ISA bridges and treats the second bridge as an ACPI system resource
device.
Reviewed by: njl (a while ago)
MFC after: 3 days
to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
voltage of 0. This can result in a divide by zero trap. Add a guard
for this case. The value of lfcap is checked in acpi_battery_bif_valid()
just before this, so it is safe.
Reportd by: sam
Approved by: re
MFC after: 3 days
of directly from acpi0. Before it would attach prior to the sysresource
devices, causing the later allocation of its memory range to fail and
print a warning like "acpi0: reservation of fed00000, 1000 (3) failed".
Use an explicit define for our probe order base value of 10.
Help from: jhb
Tested by: Abdullah Ibn Hamad Al-Marri <almarrie / gmail.com>
MFC after: 3 days
Approved by: re
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
polling/interrupt-driven fallback and instead use polling only during
boot and pure interrupt-driven mode after boot. Polled mode could be
relegated completely to a legacy role if we could enable interrupts
during boot. Polled mode can be forced after boot by setting
debug.acpi.ec.polled="1", i.e. if there are timeouts.
- Use polling only during boot, shutdown, or if requested by the user.
Otherwise, use a generation count of GPEs, incremented atomically. This
prevents an old status value from being used if the EC is really slow
and the same condition (i.e. multiple IBEs for a write transaction) is
being checked.
- Check for and run the query handler directly if the SCI bit is set in
the status register during boot. Previously, the query handler wouldn't
run until interrupts were finally enabled late in boot.
- During boot and after starting a command, check if the event appears
to already have occurred before we even start waiting. If so, it's
possible the EC is very slow and we might accept an old status value.
Print a warning in this case. Once we've booted, interrupt-driven mode
should work just fine but polled mode could be unreliable. There's not
much more we can do about this until interrupts are enabled during boot.
- In the above case, we also do one final check if the interrupt-driven
mode gets a timeout. If the status is complete, it will force the
system back into polled mode since interrupt mode doesn't work. For
polled mode during boot, if the status appears to be already complete
before beginning the check loop, it waits 10 us before actually checking
the status, just in case the EC is really slow and hasn't gotten to work
on the new request yet.
- Use upper-case hex for the _Qxx method
- Use device_printf for errors, don't hide them under verbose
- Increase default total timeout to 750 ms and decrease polling interval
to 5 us.
- Don't pass the status value via the softc. Just read it directly.
- Remove the mutex. We use the sx lock for transaction serialization
with the query handler.
- Remove the Intel copyright notice as no code of theirs was ever
present in this file (verified against rev 1.1)
- Allow KTR module-only builds for ease of testing
Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing.
Approved by: re
MFC after: 2 weeks
needed at least to convince the BIOS to give us access to CPU freq
control on MacBooks.
Submitted by: Rui Paulo <rpaulo / fnop.net>
Approved by: re
MFC after: 5 days
the fast or safe/slow method is in use. Fast remains at 1000, slow is
now at 850 (always preferred to TSC). Since the HPET has proven slower
than ACPI-fast on some systems, drop its quality to 900. In the future,
it is hoped that HPET performance will improve as it is the main
timer Intel supports. HPET may move back to 2000 in -current once RELENG_7
is branched to ensure that it gets tested.
Approved by: re
advancing. Read from the timer before attaching to be sure it advances
in 1 us. Since the slowest rate allowed by the spec is 10 MHz, the
timer is guaranteed to change in this interval if it is working.
Tested by: Rui Paulo
Approved by: re
MFC after: 3 days
switch (i.e. lid) is set to have an action of NONE. This is not an
invalid state, so silently return. This fixes the warning:
"acpi: request to enter state S6 failed (err 22)"
Approved by: re
Improvements:
* /etc/rc.suspend,rc.resume are always run, no matter the source of the
suspend request (user or kernel, apm or acpi)
* suspend now requires positive user acknowledgement. If a user program
wants to cancel the suspend, they can. If one of the user programs
hangs or doesn't respond within 10 seconds, the system suspends anyway.
* /dev/apm is clonable, allowing multiple listeners for suspend events.
In the future, xorg-server can use this to be informed about suspend
even if there are other listeners (i.e. apmd).
Changes:
* Two new ACPI ioctls: REQSLPSTATE and ACKSLPSTATE. Request begins the
process of suspending by notifying all listeners. acpi is monitored by
devd(8) and /dev/apm listener(s) are also counted. Users register their
approval or disapproval via Ack. If anyone disapproves, suspend is vetoed.
* Old user programs or kernel modules that used SETSLPSTATE continue to
work. A message is printed once that this interface is deprecated.
* acpiconf gains the -k flag to ack the suspend request. This flag is
undocumented on purpose since it's only used by /etc/rc.suspend. It is
not intended to be a permanent change and will be removed once a better
power API is implemented.
* S5 (power off) is no longer supported via acpiconf -s 5 or apm -z/-Z.
This restores previous behavior of halt/shutdown -p being the interface.
* Miscellaneous improvements to error reporting
Approved by: re
sysctl_handle_int is not sizeof the int type you want to export.
The type must always be an int or an unsigned int.
Remove the instances where a sizeof(variable) is passed to stop
people accidently cut and pasting these examples.
In a few places this was sysctl_handle_int was being used on 64 bit
types, which would truncate the value to be exported. In these
cases use sysctl_handle_quad to export them and change the format
to Q so that sysctl(1) can still print them.
While in the suspend path, this means the idle thread will just return
immediately rather than trying to enter C1-n. This helps in the case where
the chipset is powered down before the rest of the system and reads from
the cpu sleep registers begin returning immediately, causing the logic that
catches bad C2/C3 behavior to kick in. Observed on my Panasonic Y4.
MFC after: 3 days
(j/i) was being used and it was being incremented, not decremented as before.
Factor out this code into a common function and call it from both the common
and per-CPU case.
MFC after: 1 day
The global lock is a memory region shared with the BIOS and thus
has some strange behavior like the fact that the sleep is 1 ms max.
We use standard mutexes to synchronize with the SCI so acquiring
the global lock after locking the mutex resulted in a witness
warning.
To deal with this for now, acquire the global lock before all other
locks, similar to Giant. This should fix the witness "sleeping
with mutex held" issue on boot that occurred after the last ACPI-CA
import. In the future, we hope to move to the new mutex interface
in ACPI-CA instead of the pseudo-semaphore version we have now.
Reviewed by: jkim
back in a simulated resume instead of entering the requested suspend state.
This helps in testing drivers separately from the acpi suspend code. To
test your drivers, set debug.acpi.suspend_bounce=1 and then run
acpiconf -s3 (or 4).
MFC after: 1 day
