proceed while g_unload_class() blocks the event thread. Fix this by not
running g_unload_class() as a GEOM event and dropping the topology lock
when withering needs to proceed.
PR: kern/139847
Silence on: freebsd-geom
with I/O requests in flight on kernels compiled with "options INVARIANTS".
Also, make it obvious it's not right to call g_valid_obj() (and macros
using it, e.g. G_VALID_CONSUMER()) without topology lock held.
Approved by: re (kib)
Reported by: pho
allows the class to create a different GEOM for the same provider
as well as avoid that we end up with multiple GEOMs of the same
class with the same name.
For example, when a disk contains a PC98 partition table but
only MBR is supported, then the partition table can be treated
as a MBR. If support for PC98 is later loaded as a module, the
MBR scheme is pre-empted for the PC98 scheme as expected.
to it for tasting. This is useful when the class, through means outside
the scope of GEOM, can claim providers previously unclaimed.
The g_retaste() function posts an event which is handled by the
g_retaste_event().
Event suggested by: phk
particular provider. Use this function where g_orphan_provider()
is being called so that the flags are updated correctly and
g_orphan_provider() is called only when allowed.
the underlying drive had been hot-unplugged from the system. Here
is a specific example. Filesystem code had opened /dev/da1s1e.
Subsequently, the drive was hot-unplugged. This (correctly) caused
all of the associated /dev/da1* entries to be deleted. When the
filesystem later realized that the drive was gone it closed the
device, reducing the write-access counts to 0 on the geom providers
for da1s1e, da1s1, and da1. This caused geom to re-taste the
providers, resulting in the devices being created again. When the
drive was hot-plugged back in, it resulted in duplicate /dev entries
for da1s1e, da1s1, and da1.
This fix adds a new disk_gone() function which is called by CAM when a
drive goes away. It orphans all of the providers associated with the
drive, setting an error condition of ENXIO in each one. In addition,
we prevent a re-taste on last close for writing if an error condition
has been set in the provider.
Sponsored by: Isilon Systems
Reviewed by: phk
MFC after: 1 week
by the time that kldload(8) returns. Satisfy that by making the GEOM
module load event -- only when the kernel is !cold -- wait until the
GEOM module init function has finished instead of returning immediately.
This is the other half of fixing md(8) (actually, "mfs" in fstab(5))
that is similar to r1.128 of src/sys/dev/md/md.c. This bug would be
why RAM disks would often fail on boot and the first call to mdconfig(8)
would probably fail.
pjd has ideas for not requiring kldload(8) to work synchronously for
control devices that could make this obsolete.
Silence on: -arch
sectorsize in order to avoid a lot of checks around various divisions etc.
Enforce the sectorsize being > 0 with a KASSERT on successful open.
Fix scsi_cd.c to return 2k sectors when no media inserted.
understood. This makes room for additional binary compatibility in the
future.
Put fields in the class for the geom's methods and initialize the methods
of a new geom from these fields. This saves some code in all classes.
When we orphan/wither a provider, an attached geom+consumer could
end up being withered as a result and it may be in front of us in
the normal object scanning order so we need to do multi-pass. On
the other hand, there may be withering stuff we can't get rid off
(yet), so we need to keep track of both the existence of withering
stuff and if there is more we can do at this time.
Retire g_sanity() and corresponding debugflag (0x8)
Retire g_{stall,release}_events().
Under #ifdef DIAGNOSTIC:
Make g_valid_obj() an official function and have it return an an
non-zero integer which indicates the kind of object when found.
Implement G_VALID_{CLASS,GEOM,CONSUMER,PROVIDER}() macros based
on g_valid_obj().
Sprinkle calls to these macros liberally over the infrastructure.
Always check that we do not free a live object.
shown that it is not useful.
Rename the relative count g_access_rel() function to g_access(), only
the name has changed.
Change all g_access_rel() calls in our CVS tree to call g_access() instead.
Add an #ifndef BURN_BRIDGES #define of g_access_rel() for source
code compatibility.
rather than right before and right after. This allows these routines
to manipulate the mesh.
KASSERT that nobody creates a geom on an alien class.
Assert topology in g_valid_obj().
Approved by: re@
