INADDR_NONE: Incoming packets go to the alias address (the default)
INADDR_ANY: Incoming packets are not NAT'd (direct access to the
internal network from outside)
anything else: Incoming packets go to the specified address
Change a few inaddr::s_addr == 0 to inaddr::s_addr == INADDR_ANY
while I'm there.
redirected and when no target address has been specified, NAT
the destination address to the alias address rather than
allowing people direct access to your internal network from
outside.
mbuf is marked for delayed checksums, then additionally mark the
packet as having it's checksums computed. This allows us to bypass
computing/checking the checksum entirely, which isn't really needeed
as the packet has never hit the wire.
Reviewed by: green
Reported in Usenet by: locke@mcs.net (Peter Johnson)
While i was at it, prepended a 0x to the %D output, to make it clear that
the printed value is in hex (i assume %D has been chosen over %#x to
obey network byte order).
improperly doing the equivalent of (m = (function() == NULL)) instead
of ((m = function()) == NULL).
This fixes a NULL pointer dereference panic with runt arp packets.
Remove a bogus (redundant, just weird, etc.) key_freeso(so).
There are no consumers of it now, nor does it seem there
ever will be.
in6?_pcb.c:
Add an if (inp->in6?p_sp != NULL) before the call to
ipsec[46]_delete_pcbpolicy(inp). In low-memory conditions
this can cause a crash because in6?_sp can be NULL...
from iso88025.h.
o Add minimal llc support to iso88025_input.
o Clean up most of the source routing code.
* Submitted by: Nikolai Saoukh <nms@otdel-1.org>
Now most big problem of IPv6 is getting IPv6 address
assignment.
6to4 solve the problem. 6to4 addr is defined like below,
2002: 4byte v4 addr : 2byte SLA ID : 8byte interface ID
The most important point of the address format is that an IPv4 addr
is embeded in it. So any user who has IPv4 addr can get IPv6 address
block with 2byte subnet space. Also, the IPv4 addr is used for
semi-automatic IPv6 over IPv4 tunneling.
With 6to4, getting IPv6 addr become dramatically easy.
The attached patch enable 6to4 extension, and confirmed to work,
between "Richard Seaman, Jr." <dick@tar.com> and me.
Approved by: jkh
Reviewed by: itojun
ARP packets. This can incorrectly reject complete frames since the frame
could be stored in more than one mbuf.
The following patches fix the length comparisson, and add several
diagnostic log messages to the interrupt handler for out-of-the-norm ARP
packets. This should make ARP problems easier to detect, diagnose and
fix.
Submitted by: C. Stephen Gunn <csg@waterspout.com>
Approved by: jkh
Reviewed by: rwatson
Without this, kernel will panic at getsockopt() of IPSEC_POLICY.
Also make compilable libipsec/test-policy.c which tries getsockopt() of
IPSEC_POLICY.
Approved by: jkh
Submitted by: sakane@kame.net
KAME put INET6 related stuff into sys/netinet6 dir, but IPv6
standard API(RFC2553) require following files to be under sys/netinet.
netinet/ip6.h
netinet/icmp6.h
Now those header files just include each following files.
netinet6/ip6.h
netinet6/icmp6.h
Also KAME has netinet6/in6.h for easy INET6 common defs
sharing between different BSDs, but RFC2553 requires only
netinet/in.h should be included from userland.
So netinet/in.h also includes netinet6/in6.h inside.
To keep apps portability, apps should not directly include
above files from netinet6 dir.
Ideally, all contents of,
netinet6/ip6.h
netinet6/icmp6.h
netinet6/in6.h
should be moved into
netinet/ip6.h
netinet/icmp6.h
netinet/in.h
but to avoid big changes in this stage, add some hack, that
-Put some special macro define into those files under neitnet
-Let files under netinet6 cause error if it is included
from some apps, and, if the specifal macro define is not
defined.
(which should have been defined if files under netinet is
included)
-And let them print an error message which tells the
correct name of the include file to be included.
Also fix apps which includes invalid header files.
Approved by: jkh
Obtained from: KAME project
at the same time.
When rfc1323 and rfc1644 option are enabled by sysctl,
and tcp over IPv6 is tried, kernel panic happens by the
following check in tcp_output(), because now hdrlen is bigger
in such case than before.
/*#ifdef DIAGNOSTIC*/
if (max_linkhdr + hdrlen > MHLEN)
panic("tcphdr too big");
/*#endif*/
So change the above check to compare with MCLBYTES in #ifdef INET6 case.
Also, allocate a mbuf cluster for the header mbuf, in that case.
Bug reported at KAME environment.
Approved by: jkh
Reviewed by: sumikawa
Obtained from: KAME project
This is fix to usr.sbin/trpt and tcp_debug.[ch]
I think of putting this after 4.0 but,,,
-There was bug that when INET6 is defined,
IPv4 socket is not traced by trpt.
-I received request from a person who distribute a program
which use tcp_debug interface and print performance statistics,
that
-leave comptibility with old program as much as possible
-use same interface with other OSes
So, I talked with itojun, and synced API with netbsd IPv6 extension.
makeworld check, kernel build check(includes GENERIC) is done.
But if there happen to any problem, please let me know and
I soon backout this change.
o Drop all broadcast and multicast source addresses in tcp_input.
o Enable ICMP_BANDLIM in GENERIC.
o Change default to 200/s from 100/s. This will still stop the attack, but
is conservative enough to do this close to code freeze.
This is not the optimal patch for the problem, but is likely the least
intrusive patch that can be made for this.
Obtained from: Don Lewis and Matt Dillon.
Reviewed by: freebsd-security
for IPv4 communication.(IPv4 mapped IPv6 addr.)
Also removed IPv6 hoplimit initialization because it is alway done at
tcp_output.
Confirmed by: Bernd Walter <ticso@cicely5.cicely.de>
include this in all kernels. Declare some const *intrq_present
variables that can be checked by a module prior to using *intrq
to queue data.
Make the if_tun module capable of processing atm, ip, ip6, ipx,
natm and netatalk packets when TUNSIFHEAD is ioctl()d on.
Review not required by: freebsd-hackers
-opt_ipsec.h was missing on some tcp files (sorry for basic mistake)
-made buildable as above fix
-also added some missing IPv4 mapped IPv6 addr consideration into
ipsec4_getpolicybysock
