we were passing in a void* representing the PCB of the parent thread.
Now we pass a pointer to the parent thread itself.
The prime reason for this change is to allow cpu_set_upcall() to copy
(parts of) the trapframe instead of having it done in MI code in each
caller of cpu_set_upcall(). Copying the trapframe cannot always be
done with a simply bcopy() or may not always be optimal that way. On
ia64 specifically the trapframe contains information that is specific
to an entry into the kernel and can only be used by the corresponding
exit from the kernel. A trapframe copied verbatim from another frame
is in most cases useless without some additional normalization.
Note that this change removes the assignment to td->td_frame in some
implementations of cpu_set_upcall(). The assignment is redundant.
A previous call to cpu_thread_setup() already did the exact same
assignment. An added benefit of removing the redundant assignment is
that we can now change td_pcb without nasty side-effects.
This change officially marks the ability on ia64 for 1:1 threading.
Not tested on: amd64, powerpc
Compile & boot tested on: alpha, sparc64
Functionally tested on: i386, ia64
This machine uses a non-standard scheme to specify the interrupts to
be assigned for devices in PCI slots; instead of giving the INO
or full interrupt number (which is done for the other devices in this
box), the firmware interrupt properties contain intpin numbers, which
have to be swizzled as usual on PCI-PCI bridges; however, the PCI host
bridge nodes have no interrupt map, so we need to guess the
correct INO by slot number of the device or the closest PCI-PCI
bridge leading to it, and the intpin.
To do this, this fix makes the following changes:
- Add a newbus method for sparc64 PCI host bridges to guess
the INO, and glue code in ofw_pci_orb_callback() to invoke it based
on a new quirk entry. The guessing is only done for interrupt numbers
too low to contain any IGN found on e450s.
- Create another new quirk entry was created to prevent mapping of EBus
interrupts at PCI level; the e450 has full INOs in the interrupt
properties of EBus devices, so trying to remap them could cause
problems.
- Set both quirk entries for e450s; remove the no-swizzle entry.
- Determine the psycho half (bus A or B) a driver instance manages
in psycho_attach()
- Implement the new guessing method for psycho, using the slot number,
psycho half and property value (intpin).
Thanks go to the testers, especially Brian Denehy, who tested many kernels
for me until I had found the right workaround.
Tested by: Brian Denehy <B.Denehy@90east.com>, jake, fenner,
Marius Strobl <marius@alchemy.franken.de>,
Marian Dobre <mari@onix.ro>
Approved by: re (scottl)
The current name is confusing, because it indicates to
the client that a bus_dmamap_sync() operation is not
necessary when the flag is specified, which is wrong.
The main purpose of this flag is to hint the underlying
architecture that DMA memory should be mapped in a coherent
way, but the architecture can ignore it. But if the
architecture does supports coherent mapping of memory, then
it makes bus_dmamap_sync() calls cheap.
This flag is the same as the one in NetBSD's Bus DMA.
Reviewed by: gibbs, scottl, des (implicitly)
Approved by: re@ (jhb)
value to be written into tick_compare in tick_hardclock(). While
we were taking care that the value to be written was at least TICK_GRACE
ticks in the future, a vector interrupt could happen between calculating
the value and writing it. If it took longer than TICK_GRACE to complete
(which is doubtful for a single device-triggered vector interrupt, but
quite likely for some IPIs), the value written would be in the past
and tick interrupts (which drive hardclock and statclock) would stop
until %tick wraps around, which takes a long time.
Also, increase TICK_GRACE from 1000 to 10000 for good measure.
Reported by: kris
Reviewed by: jake
Approved by: re (scottl)
BUS_DMASYNC_ definitions remain as before. The does not change the ABI,
and reverts the API to be a bit more compatible and flexible. This has
survived a full 'make universe'.
Approved by: re (bmah)
- Fix visibilty test for LONG_BIT and WORD_BIT. `#if defined(__FOO_VISIBLE)'
is alays wrong because __FOO_VISIBLE is always defined (to 0 for
invisibility).
sys/<arch>/include/limits.h
sys/<arch>/include/_limits.h:
- Style fixes.
Submitted by: bde
Reviewed by: bsdmike
Approved by: re (scottl)
- Move struct sigacts out of the u-area and malloc() it using the
M_SUBPROC malloc bucket.
- Add a small sigacts_*() API for managing sigacts structures: sigacts_alloc(),
sigacts_free(), sigacts_copy(), sigacts_share(), and sigacts_shared().
- Remove the p_sigignore, p_sigacts, and p_sigcatch macros.
- Add a mutex to struct sigacts that protects all the members of the struct.
- Add sigacts locking.
- Remove Giant from nosys(), kill(), killpg(), and kern_sigaction() now
that sigacts is locked.
- Several in-kernel functions such as psignal(), tdsignal(), trapsignal(),
and thread_stopped() are now MP safe.
Reviewed by: arch@
Approved by: re (rwatson)
Remove DBL_DIG, DBL_MIN, DBL_MAX and their FLT_ counterparts, they
were marked for deprecation ever since SUSv1 at least.
Only define ULLONG_MIN/MAX and LLONG_MAX if long long type is
supported.
Restore a lost comment in MI _limits.h file and remove it from
sys/limits.h where it does not belong.
quite excessive, and caused the available space to be used up too
easily. The new limit should be a better estimation of how much the
caller will need at most.
- Double the IOTSB size 64kB, for a DVMA area size of 64MB.
This should fix DMA problems on e450s and other large machines due
to DVMA space exhaustion, which were introduced in my last IOMMU
code revision in January.
Reported and tested by: fenner
that were added to sparc64 and later powerpc, really should have been in
the MI area. But changing that now with insufficient preperation will
just cause too much pain.
Move MD_FETCH() to the MI sys/linker.h file to avoid another two copies
of it.
syscall return values should be cleared. The system calls
getcontext() and swapcontext() want to return 0 on success
but these contexts can be switched to at a later time so
the return values need to be cleared in the saved register
sets. Other callers of get_mcontext() would normally want
the context without clearing the return values.
Remove the i386-specific context saving from the KSE code.
get_mcontext() is not i386-specific any more.
Fix a bad pointer in the alpha get_mcontext() code. The
context was being bcopy()'d from &td->tf_frame, but tf_frame
is itself a pointer, so the thread was being copied instead.
Spotted by jake.
Glanced at by: jake
Reviewed by: bde (months ago)
to get actual constant values. This is in preparation for machine/limits.h
retirement.
Discussed on: standards@
Submitted by: Craig Rodrigues <rodrigc@attbi.com> (*)
Modified by: kan
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
the cpu dependent files. It will need to be done differently for USIII.
- Simplify the logic for detecting context rollovers. Instead of dealing
with it when the next context switch would cause the context numbers to
rollover, deal with it when they actually do rollover.
- Move some things around in cpu_switch so that we only do 1 membar #Sync
when switching address space, instead of 2.
- Detect kernel threads by comparing the new vm space to vmspace0, instead
if checking if the tlb context is 0.
- Removed some debug code.
enum to an int and redefine the BUS_DMASYNC_* constants as
flags. This allows us to specify several operations in one
call to bus_dmamap_sync() as in NetBSD.
of asserting that an mbuf has a packet header. Use it instead of hand-
rolled versions wherever applicable.
Submitted by: Hiten Pandya <hiten@unixdaemons.com>
These are called through function pointers so that different implementations
can be provided for cheetah, where the block load instructions may or may
not be a win, and so they can be disabled with the machdep.use_vis tunable.
In terms of raw bandwidth the integer versions are faster, but not allocating
lines in the L2 cache for useless data gives a measurable improvement in user
time for the benchmarks I tested (mostly buildworld with -j8).
As far as I can tell the instructions used are implemented on everything
back to UltraSPARC I, so there should not be a problem with different cpu
types.
to take care of the KAME IPv6 code which needs ovbcopy() because NetBSD's
bcopy() doesn't handle overlap like ours.
Remove all implementations of ovbcopy().
Previously, bzero was a function pointer on i386, to save a jmp to
bzero_vector. Get rid of this microoptimization as it only confuses
things, adds machine-dependent code to an MD header, and doesn't really
save all that much.
This commit does not add my pagezero() / pagecopy() code.
can do 64 bytes at a time and don't allocate lines in the L2 cache. These
assume that everything is 64 byte aligned, and that there's more than 128
bytes of data (best for whole pages). The block load and store instructions
don't follow normal memory ordering rules and require either a memory barrier
or move between registers before the data can actually be used. This
implementation correctly shuffles around 3 out of the 4 sets of registers
in order to avoid memory barriers expect for the last 2 blocks.
will be saved if we context switch as a result of an interrupt which occured
while using the floating point registers in the kernel (which actually can't
happen right now). This allows fp disabled traps in the kernel, which
normally shouldn't happen, so make sure the trapping code is what we expect
it is.
used to support block copy and zero operations in the kernel which use the
floating point registers.
- While I'm changing the size, improve the layout of struct pcb, sort by size,
then alphabetical etc.
- Add some assertions to validate assumptions made about how the pcb is
allocated.
for temporaries relating to the state of the new process instead of the
outs, so that functions can be called without fear of clobbering them.
- Use savefpctx instead of rolling our own.
as it could be and can do with some more cleanup. Currently its under
options LAZY_SWITCH. What this does is avoid %cr3 reloads for short
context switches that do not involve another user process. ie: we can
take an interrupt, switch to a kthread and return to the user without
explicitly flushing the tlb. However, this isn't as exciting as it could
be, the interrupt overhead is still high and too much blocks on Giant
still. There are some debug sysctls, for stats and for an on/off switch.
The main problem with doing this has been "what if the process that you're
running on exits while we're borrowing its address space?" - in this case
we use an IPI to give it a kick when we're about to reclaim the pmap.
Its not compiled in unless you add the LAZY_SWITCH option. I want to fix a
few more things and get some more feedback before turning it on by default.
This is NOT a replacement for Bosko's lazy interrupt stuff. This was more
meant for the kthread case, while his was for interrupts. Mine helps a
little for interrupts, but his helps a lot more.
The stats are enabled with options SWTCH_OPTIM_STATS - this has been a
pseudo-option for years, I just added a bunch of stuff to it.
One non-trivial change was to select a new thread before calling
cpu_switch() in the first place. This allows us to catch the silly
case of doing a cpu_switch() to the current process. This happens
uncomfortably often. This simplifies a bit of the asm code in cpu_switch
(no longer have to call choosethread() in the middle). This has been
implemented on i386 and (thanks to jake) sparc64. The others will come
soon. This is actually seperate to the lazy switch stuff.
Glanced at by: jake, jhb
set_mcontext.
- Don't make assumptions about the alignment of the mcontext inside of the
ucontext; we have to save the floating point registers to the pcb and then
copy to the mcontext.
a pointer that is in user space. It will be used as the basic primitive
for a kernel supported user space lock implementation.
- Implement this function in x86's support.s
- Provide stubs that return -1 in all other architectures. Implementations
will follow along shortly.
Reviewed by: jake
a follow on commit to kern_sig.c
- signotify() now operates on a thread since unmasked pending signals are
stored in the thread.
- PS_NEEDSIGCHK moves to TDF_NEEDSIGCHK.
- Change all consumers to pass in a thread.
Right now this does not cause any functional changes but it will be important
later when signals can be delivered to specific threads.
be overridden by setting hw.physmem.
- Fix a vm_map_find arg, we don't want to find space.
- Add tracing and statistics for off colored pages.
- Detect "stupid" pmap_kenters (same virtual and physical as existing
mapping), and do nothing in that case.
pages which represent actual physical memory we must strip off the fake
page in order to allow illegal aliases to be detected. Otherwise we map
uncacheable in the virtual and physical caches and set the side effect bit,
as is required for mapping device memory.
This fixes gstat on sparc64, which wants to mmap kernel memory through a
character device.
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
in busdma tags. There are currently no tags shared accross
different drivers so this isn't needed at the moment, but it
will be required when we'll have a proper newbus method to get
the parent busdma tag.
on future UltraSPARC cpus for which the data cache is not direct mapped.
- Move UltraSPARC I and II (spitfire, blackbird, sapphire, sabre) specific
functions to spitfire.c, and add cheetah.c for UltraSPARC III specific
functions. Initially just cache flushing, but there are a few other
functions that will need to move here.
- Add an ipi handler for data cache flushing on UltraSPARC III.
- Use function pointers to select the right cache flushing functions based
on cpu_impl.
With this it is possible to boot single user from an mfs root on UltraSPARC
III systems, including spinning up secondary processors. There is currently
no support for the host to pci bridge, and no documentation for it is
publically available.
Thanks to Oleg Derevenetz for providing access to a system with UltraSPARC
III+ cpus.
UltraSPARC III and higher cpus and do needed setup.
- Disable the "system tick" interrupt for UltraSPARC III. This avoids
an interrupt storm on startup since we're not prepared for these at
all. This feature has questionable use anyway.
- Clear tick on startup and then leave it alone.
are machine dependent because they are not required to update the tlb when
mappings are added or removed, and doing so is machine dependent.
In addition, an implementation may require that pages mapped with pmap_kenter
have a backing vm_page_t, which is not necessarily true of all physical
pages, and so may choose to pass the vm_page_t to pmap_kenter instead of the
physical address in order to make this requirement clear.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
Fixed memory leak in the "nodevice" option implementation.
Use these instead of sed(1) in MD NOTES.
Use a single makefile (sys/conf/makeLINT.mk) to generate
LINT for all architectures. (Previous versions missed
the LINT dependency on Makefile, and i386 version also
missed the dependency on ${NOTES}.)
Fixed bugs in the previous NOTES conversion using the
"nodevice" token and sed(1):
- i386 LINT lost "device pst".
- pc98 LINT lost SC_*, MAXCONS and KBD_DISABLE_KEYMAP_LOAD
options, and got needless DPT_* options.
- Added nooptions PPC_DEBUG, PPC_PROBE_CHIPSET, KBD_INSTALL_CDEV
to sparc64 LINT so that it has a chance to config(8).
This basically returns us to where we were before.
- Get rid of the useless atop() / pmap_phys_address() detour. The
device mmap handlers must now give back the physical address
without atop()'ing it.
- Don't borrow the physical address of the mapping in the returned
int. Now we properly pass a vm_offset_t * and expect it to be
filled by the mmap handler when the mapping was successful. The
mmap handler must now return 0 when successful, any other value
is considered as an error. Previously, returning -1 was the only
way to fail. This change thus accidentally fixes some devices
which were bogusly returning errno constants which would have been
considered as addresses by the device pager.
- Garbage collect the poorly named pmap_phys_address() now that it's
no longer used.
- Convert all the d_mmap_t consumers to the new API.
I'm still not sure wheter we need a __FreeBSD_version bump for this,
since and we didn't guarantee API/ABI stability until 5.1-RELEASE.
Discussed with: alc, phk, jake
Reviewed by: peter
Compile-tested on: LINT (i386), GENERIC (alpha and sparc64)
Runtime-tested on: i386
