Don't document non-bugs in the BUGS section, or anywhere else. It
is not a bug to drop data when overloaded. The compile-time tuning
options turned out to be not very useful, and aren't supported
offically.
Documented the not so new option CY_PCI_FASTINTR.
to implement multi-link ppp over more than one ISP with
the ability to lose ISPs without loss of connectivity.
It *requires* that you either have administrative access
to a machine that's already connected to the 'net or at
least know a really nice person that does.
(QIC) written under 2.X may not be easily read under the current
driver without explicitly setting to variable mode or to the blocksize
these tapes were written under 2.X with.
PR: 6681
similar to the PNIC I (supported by the pn driver). In fact, it's really
a Macronix 98715A with wake on LAN support added. According to LinkSys,
the PNIC II was jointly developed by Lite-On and Macronis. I get the
feeling Macronix did most of the work. (The datasheet has the Macronix
logo on it, and is in fact nearly identical to the 98715 datasheet, except
for the extra wake on LAN registers.) In any case, the PNIC II works just
fine with the Macronix driver.
The changes are:
- Move PCI ID for the PNIC II from the pn driver to the mx driver.
- Mention PNIC II support in mx.4.
- Mention PNIC II support in RELNOTES.TXT and HARDWARE.TXT.
- Mention that the 6Mbps turbo adapters are supported in HARDWARE.TXT
and RELNOTES.TXT and the wi.4 man page
- Mention turbo adapters in the wicontrol.8 man page and provide a
complete table of available transmit speed settings
ADMtek AL981 "Comet" chipset. The AL981 is yet another DEC tulip clone,
except with simpler receive filter options. The AL981 has a built-in
transceiver, power management support, wake on LAN and flow control.
This chip performs extremely well; it's on par with the ASIX chipset
in terms of speed, which is pretty good (it can do 11.5MB/sec with TCP
easily).
I would have committed this driver sooner, except I ran into one problem
with the AL981 that required a workaround. When the chip is transmitting
at full speed, it will sometimes wedge if you queue a series of packets
that wrap from the end of the transmit descriptor list back to the
beginning. I can't explain why this happens, and none of the other tulip
clones behave this way. The workaround this is to just watch for the end
of the transmit ring and make sure that al_start() breaks out of its
packet queuing loop and waiting until the current batch of transmissions
completes before wrapping back to the start of the ring. Fortunately, this
does not significantly impact transmit performance.
This is one of those things that takes weeks of analysis just to come
up with two or three lines of code changes.
is likely the intent of the original author since no other places use
tabs.
Sync us.unix.kdb to us.iso.kbd. It should now only swap ESC and `~,
bs and delete, control and caps lock and make no other changes from
us.iso.kdb.
adapter (and some workalikes). Also add man pages and a wicontrol
utility to manipulate some of the card parameters.
This driver was written using information gleaned from the Lucent HCF Light
library, though it does not use any of the HCF Light code itself, mainly
because it's contaminated by the GPL (but also because it's pretty gross).
The HCF Light lacks certain featurs from the full (but proprietary) HCF
library, including 802.11 frame encapsulation support, however it has
just enough register information about the Hermes chip to allow someone
with enough spare time and energy to implement a proper driver. (I would
have prefered getting my hands on the Hermes manual, but that's proprietary
too. For those who are wondering, the Linux driver uses the proprietary
HCF library, but it's provided in object code form only.)
Note that I do not have access to a WavePOINT access point, so I have
only been able to test ad-hoc mode. The wicontrol utility can turn on
BSS mode, but I don't know for certain that the NIC will associate with
an access point correctly. Testers are encouraged to send their results
to me so that I can find out if I screwed up or not.
are from 3.x-stable which was branched quite some time after 3.0-release
(about Jan 15 if I recall correctly).
----> FreeBSD-3.0-----\----- FreeBSD-4.x-current -----....
\
3.x-stable ----> 3.1 ---> 3.2 ....
Submitted by: peter
Added upcoming releases FreeBSD 3.2, NetBSD 1.3, OpenBSD 2.5
NetBSD 1.2.1 is a patch release of NetBSD 1.2 (a branch of 1.2)
NetBSD 1.3.1, 1.3.2, 1.3.3 are a patch release of NetBSD 1.3 (a branch of 1.3).
FreeBSD 3.0, FreeBSD 3.1 and FreeBSD 3.2 are a releases
from the 3.0-stable branch.
Added FreeBSD 4.0-current.
Added FreeBSD 3.1 release date.
This is a seriously beefed up chroot kind of thing. The process
is jailed along the same lines as a chroot does it, but with
additional tough restrictions imposed on what the superuser can do.
For all I know, it is safe to hand over the root bit inside a
prison to the customer living in that prison, this is what
it was developed for in fact: "real virtual servers".
Each prison has an ip number associated with it, which all IP
communications will be coerced to use and each prison has its own
hostname.
Needless to say, you need more RAM this way, but the advantage is
that each customer can run their own particular version of apache
and not stomp on the toes of their neighbors.
It generally does what one would expect, but setting up a jail
still takes a little knowledge.
A few notes:
I have no scripts for setting up a jail, don't ask me for them.
The IP number should be an alias on one of the interfaces.
mount a /proc in each jail, it will make ps more useable.
/proc/<pid>/status tells the hostname of the prison for
jailed processes.
Quotas are only sensible if you have a mountpoint per prison.
There are no privisions for stopping resource-hogging.
Some "#ifdef INET" and similar may be missing (send patches!)
If somebody wants to take it from here and develop it into
more of a "virtual machine" they should be most welcome!
Tools, comments, patches & documentation most welcome.
Have fun...
Sponsored by: http://www.rndassociates.com/
Run for almost a year by: http://www.servetheweb.com/
transceiver. Note in the manual page that autoselection doesn't
work on the 82c168 because the built-in NWAY support is horribly
broken. Manual mode selection works fine, but autoneg is broken for
everything except maybe 10Mbps half-duplex. There's no simple way
to fix this at the moment, so I have to settle for documenting the
bug for now. Fortunately, there aren't anywhere near as many 82c168
boards around as there are 82c169s.
I changed to "Christopher G. Demetriou" since the page appears to be a
revision of lkm(4).
PR: docs/8611
Submitted by: Rajesh Vaidheeswarran <rv@fore.com>
Networks Tigon 1 and Tigon 2 chipsets. There are a _lot_ of OEM'ed
gigabit ethernet adapters out there which use the Alteon chipset so
this driver covers a fair amount of hardware. I know that it works with
the Alteon AceNIC, 3Com 3c985 and Netgear GA620, however it should also
work with the DEC/Compaq EtherWORKS 1000, Silicon Graphics Gigabit
ethernet board, NEC Gigabit Ethernet board and maybe even the IBM and
and Sun boards. The Netgear board is the cheapest (~$350US) but still
yields fairly good performance.
Support is provided for jumbo frames with all adapters (just set the
MTU to something larger than 1500 bytes), as well as hardware multicast
filtering and vlan tagging (in conjunction with the vlan support in
-current, which I should merge into -stable soon). There are some hooks
for checksum offload support, but they're turned off for now since
FreeBSD doesn't have an officially sanctioned way to support checksum
offloading (yet).
I have not added the 'device ti0' entry to GENERIC since the driver
with all the firmware compiled in is quite large, and it doesn't really
fit into the category of generic hardware.
/usr/sbin/sysctl -> ${DESTDIR}/sbin/sysctl in some versions of 2.2,
and this link was broken if DESTDIR was set.
Added a SYMLINKS macro. This works the same as LINKS, except it
creates symlinks and the linked-to pathname may be relative. This
is more flexible than LN_FLAGS, since it supports installing
symlinks independently of hard links.
Use `ln -f[s] ...' instead of `rm -f ...; ln [-s] ...' for LINKS and
SYMLINKS. This is equivalent if the target is neither a directory nor
a symlink to a directory.
PR: 8279
kernel and userland modules.
Describe the superdevice method of ensuring that people at least
recognize the problem if they run into a debug synchronization problem.
it up on exit. The address for attaching the emulator (path, target id,
lun) is now specified on the command line. Some attempt at cathing
signals and cleaning up target mode instances is now made.
Describe /dev/vinum/control*
Describe drive "referenced" state.
Remove warning about kldunload; it seems to work now.
Still more descriptions of how to debug things.
AX88140A with power management and magic packet support. Correct the
addresses of the PCI power management registers and add some code to
detect the revision ID of the AX88141 and identify it in the probe
messages.
No other changes are needed since the AX88141 is functionally
identical to the AX88140A.
the peer demands authentication, and add some more detail to the
example configurations.
This is the first time I've written any TCL, so I'd appreciate it
if someone eyeballed the *-auth stuff and fixed any glaring problems.
- Add syscons.4.
If there still are errors, whether technical or grammatical, they are
entirely mine, not the reviewers'.
Reviewed by: sos, jkh, archie, Nick Hilliard <nick@iol.ie>
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
Russian zones/rules in rev.1.12. ache objected mainly to the changes
in the Moscow zone names in rev.1.11 and those changes have been backed
out in the vendor branch.
Reviewed by: ache
and Racore 8148 adapters are now supported by the ThunderLAN driver.
The 8165 is just a plain vanilla 10/100 card; the 8148 is a 'multi-
personality' adapter which can support 10baseT, 100baseTX and 100baseFX
if you include the proper modules.
Also update the tl man page to mention the Racore cards.
is not implied by -Wall as claimed by gcc.1. Adding it causes a
measly 7193 new warnings for LINT, mostly for "unused parameter" and
"comparison between signed and unsigned".
- The numpad * key should always generate *.
- The numpad - is fkey52 and should not generate a control code (0x1f).
- The numpad 5 is fkey54, not fkey61.
- The numpad 6 is fkey55 and should not generate a control code (0x1e).
- Fix Spanish keymap.
PR: i386/9532
Submitted by jose@we.lc.ehu.es.
- Added Croatian keymap. It is the same as the Slovenian keymap.
PR: misc/9706
Pointed out by: Damjan Marion
- Addef Finnish keymap. It is the same as the Swedish keymap.
PR: bin/9632
Submitted by: Martti Kuparinen
- Assign special functions consistently in all keymap files.
101 keyboard 84 keyboard function
------------------------------------------------------------------------
Ctrl-Alt-Delete Ctrl-Alt-Delete reboot
Ctrl-Alt-Esc Ctrl-Alt-Esc debug
Ctrl-Alt-Space Ctrl-Alt-Space susp
ScrollLock ScrollLock slock
PrintScreen Shift-(Numpad *)/PrintScreen nscr
Ctrl-PrintScreen Shift-Ctrl-(Numpad *)/PrintScreen debug
Alt-PrintScreen/SysRq SysRq nop
Pause Ctrl-NumLock slock
Shift-Pause Shift-Ctrl-NumLock saver
Alt-Pause Alt-Ctrl-NumLock susp
Ctrl-Pause/Break Ctrl-ScrollLock/Break nop
Left W*ndow key NA fkey62
Right W*ndow key NA fkey63
Menu NA fkey64
NOTE: us.unix.kbd and us.emacs.kbd are very much different from the
other keymaps, thus, I didn't touch them.
There are only skeletons left here; they merely serve as a backup to
include the real versions under ${PORTSDIR}/Mk while we update the ports
tree to include them directly.
<bsd.libnames.mk> is included regardless of the object file format.
This is needed to fix the a.out PAM breakage that manifests itself
when trying to build login.
of important changes to European and South and Central American countries
which should be back-ported to 3.x.
Obtained from: ftp://elsie.nci.nih.gov/pub/tzdata1999a.tar.gz
This should be merged into RELENG_3 and a similar patch may be needed
for RELENG_2_2, should that deemed necessary.
Make world succeeded with these patches in my tree.
Submitted by: "Kaleb S. KEITHLEY" <kaleb@ics.com>
When linking statically, LIBPAM is augmented with the extra libraries
that the PAM modules require. The idea is to centralize this
information rather than scattering it about in the Makefiles of
all the applications that use (OK, will use) PAM.
There is a new variable MINUSLPAM that should be used instead of
"-lpam". In the static case, it gets -l flags for the extra required
libraries.
This approach was suggested by <bde>, but he didn't actually review
my changes.
building dlopen-able modules, and add features needed to build a
static PAM library. I think I cleaned it up some, too, but beauty
is in the eye of the beholder.
You can now build a shared library without version numbers, by
defining SHLIB_NAME to something like "pam_unix.so". If SHLIB_MAJOR
and/or SHLIB_MINOR are set, SHLIB_NAME gets the usual default value,
but it can be overridden if desired. If none of these symbols are
set, no shared library is built.
SHLIB_LINK controls the name of the symbolic link that points to
the library. If it is unset, no link is made. In the usual case,
it gets the right default: e.g., "libc.so" for ELF, nothing for
a.out. This can be overridden.
STATICOBJS can be set to a list of extra object files that should
be added to the static library but not to the shared library.
These objects are added to the profiled library too.
These changes should make it easy to use <bsd.lib.mk> for building
things such as PAM modules and dynamic linkers, for which <bsd.prog.mk>
has been abused until now.
languages (en = English, de = German, zn = Chinese, and so on). This
complements the existing iso3166 file, which maps codes to countries.
Country code != language code.
I ran this past -core. No one voiced any objections, jkh said "fine".
