to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
providers with limited physical storage and add physical storage as
needed.
Submitted by: Ivan Voras
Sponsored by: Google Summer of Code 2006
Approved by: re (kensmith)
commented out until I can re-test them on all our architectures. I
had re@ approval to commit this a long time ago, but that's before we
were this close to the branch.
Approved by: re@
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
Also rename the related functions in a similar way.
There are no functional changes.
For a packet coming in with IPsec tunnel mode, the default is
to only call into the firewall with the "outer" IP header and
payload.
With this option turned on, in addition to the "outer" parts,
the "inner" IP header and payload are passed to the
firewall too when going through ip_input() the second time.
The option was never only related to a gif(4) tunnel within
an IPsec tunnel and thus the name was very misleading.
Discussed at: BSDCan 2007
Best new name suggested by: rwatson
Reviewed by: rwatson
Approved by: re (bmah)
included man pages on how to use it. This code is still somewhat experimental
but has been successfully tested on a number of targets. Many thanks to
Danny for contributing this.
Approved by: re
- Add custom .c wrappers for the firmware, rather than the standard
firmware(9) generated firmware objects to work around toolchain
problems on ia64 involving linking objects produced by
ld -b -binary into the kernel.
- Move from using Myricom's ".dat" firmware blobs to using Myricom's
zlib compressed ".h" firmware header files. This is done to
facilitate the custom wrappers, and saves a fair amount of wired
memory in the case where the firmware is built in, or preloaded.
- Fix two compile issues in mxge which only appear on non-i386/amd64.
Reviewed by: mlaier, mav (earlier version with just zlib support)
Glanced at by: sam
Approved by: re (kensmith)
NET_NEEDS_GIANT, which will shortly be removed. This is done in a
away that it may be easily reattached to the build before 7.1 if
appropriate locking is added. Specifics:
- Don't install netatm include files
- Disconnect netatm command line management tools
- Don't build libatm
- Don't include ATM parts in rescue or sysinstall
- Don't install sample configuration files and documents
- Don't build kernel support as a module or in NOTES
- Don't build netgraph wrapper nodes for netatm
This removes the last remaining consumer of NET_NEEDS_GIANT.
Reviewed by: harti
Discussed with: bz, bms
Approved by: re (kensmith)
This commit includes only the kernel files, the rest of the files
will follow in a second commit.
Reviewed by: bz
Approved by: re
Supported by: Secure Computing
both 6.x and 7.x. This is based on feedbacks on this thread
http://docs.freebsd.org/cgi/getmsg.cgi?fetch=81818+0+current/freebsd-stable
and my use it on 6.x.
MFC after: 3 days
- Update the warning about UNION filesystem. It is now actively maintained,
although there are still some issues being resolved.
Reviewed by: freebsd-stable@, kris, bmah
Approved by: re (bmah)
This allocator uses a binary buddy system with a twist. First and
foremost, this allocator is required to support the implementation of
superpages. As a side effect, it enables a more robust implementation
of contigmalloc(9). Moreover, this reimplementation of
contigmalloc(9) eliminates the acquisition of Giant by
contigmalloc(..., M_NOWAIT, ...).
The twist is that this allocator tries to reduce the number of TLB
misses incurred by accesses through a direct map to small, UMA-managed
objects and page table pages. Roughly speaking, the physical pages
that are allocated for such purposes are clustered together in the
physical address space. The performance benefits vary. In the most
extreme case, a uniprocessor kernel running on an Opteron, I measured
an 18% reduction in system time during a buildworld.
This allocator does not implement page coloring. The reason is that
superpages have much the same effect. The contiguous physical memory
allocation necessary for a superpage is inherently colored.
Finally, the one caveat is that this allocator does not effectively
support prezeroed pages. I hope this is temporary. On i386, this is
a slight pessimization. However, on amd64, the beneficial effects of
the direct-map optimization outweigh the ill effects. I speculate
that this is true in general of machines with a direct map.
Approved by: re
tunnels, and was not MPSAFE. The code can be easily restored in the
event that someone with an IPX over IP tunnel configuration can work
with me to test patches.
This removes one of five remaining consumers of NET_NEEDS_GIANT.
Approved by: re (kensmith)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
The name trunk is misused as the networking term trunk means carrying multiple
VLANs over a single connection. The IEEE standard for link aggregation (802.3
section 3) does not talk about 'trunk' at all while it is used throughout IEEE
802.1Q in describing vlans.
The lagg(4) driver provides link aggregation, failover and fault tolerance.
Discussed on: current@
Linux SCSI SG passthrough device API. The intention is to allow for both
running of Linux apps that want to talk to /dev/sg* nodes, and to facilitate
porting of apps from Linux to FreeBSD. As such, both native and linuxolator
entry points and definitions are provided.
Caveats:
- This does not support the procfs and sysfs nodes that the Linux SG
driver provides. Some Linux apps may rely on these for operation,
others may only use them for informational purposes.
- More ioctls need to be implemented.
- Linux uses a naming scheme of "sg[a-z]" for devices, while FreeBSD uses a
scheme of "sg[0-9]". Devfs aliasis (symlinks) are automatically created
to link the two together. However, tools like camcontrol only see the
native names.
- Some operations were originally designed to return byte counts or other
data directly as the syscall return value. The linuxolator doesn't appear
to support this well, so this driver just punts for these cases.
Now that the driver is in place, others are welcome to add missing
functionality. Thanks to Roman Divacky for pushing this work along.
When the linux port changes were imported which split the
target command list to be separate from the initiator command
list and the handle format changed to encode a type in the handle
the implications to the function isp_handle_index (which only
the NetBSD/OpenBSD/FreeBSD ports use) were overlooked.
The fault is twofold: first, the index into the DMA maps
in isp_pci is wrong because a target command handle with
the type bit left in place caused a bad index (and panic)
into dma map. Secondly, the assumption of the array
of DMA maps in either PCS or SBUS attachment structures is
that there is a linear mapping between handle index and
DMA map index. This can no longer be true if there are
overlapping index spaces for initiator mode and target
mode commands.
These changes bandaid around the problem by forcing us
to not have simultaneous dual roles and doing the appropriate
masking to make sure things are indexed correctly. A longer
term fix is being devloped.
obtaining and releasing shared and exclusive locks. The algorithms for
manipulating the lock cookie are very similar to that rwlocks. This patch
also adds support for exclusive locks using the same algorithm as mutexes.
A new sx_init_flags() function has been added so that optional flags can be
specified to alter a given locks behavior. The flags include SX_DUPOK,
SX_NOWITNESS, SX_NOPROFILE, and SX_QUITE which are all identical in nature
to the similar flags for mutexes.
Adaptive spinning on select locks may be enabled by enabling the
ADAPTIVE_SX kernel option. Only locks initialized with the SX_ADAPTIVESPIN
flag via sx_init_flags() will adaptively spin.
The common cases for sx_slock(), sx_sunlock(), sx_xlock(), and sx_xunlock()
are now performed inline in non-debug kernels. As a result, <sys/sx.h> now
requires <sys/lock.h> to be included prior to <sys/sx.h>.
The new kernel option SX_NOINLINE can be used to disable the aforementioned
inlining in non-debug kernels.
The size of struct sx has changed, so the kernel ABI is probably greatly
disturbed.
MFC after: 1 month
Submitted by: attilio
Tested by: kris, pjd
imitating an Ethernet device, so vlan(4) and if_bridge(4) can be
attached to it for testing and benchmarking purposes. Its source
can be an introduction to the anatomy of a network interface driver
due to its simplicity as well as to a bunch of comments in it.
arrangement that has no intrinsic internal knowledge of whether devices
it is given are truly multipath devices. As such, this is a simplistic
approach, but still a useful one.
The basic approach is to (at present- this will change soon) use camcontrol
to find likely identical devices and and label the trailing sector of the
first one. This label contains both a full UUID and a name. The name is
what is presented in /dev/multipath, but the UUID is used as a true
distinguishor at g_taste time, thus making sure we don't have chaos
on a shared SAN where everyone names their data multipath as "Fred".
The first of N identical devices (and N *may* be 1!) becomes the active
path until a BIO request is failed with EIO or ENXIO. When this occurs,
the active disk is ripped away and the next in a list is picked to
(retry and) continue with.
During g_taste events new disks that meet the match criteria for existing
multipath geoms get added to the tail end of the list.
Thus, this active/passive setup actually does work for devices which
go away and come back, as do (now) mpt(4) and isp(4) SAN based disks.
There is still a lot to do to improve this- like about 5 of the 12
recommendations I've received about it, but it's been functional enough
for a while that it deserves a broader test base.
Reviewed by: pjd
Sponsored by: IronPort Systems
MFC: 2 months
Make PIM dynamically loadable by using encap_attach_func().
PIM may now be loaded into a GENERIC kernel.
Tested with: ports/net/pimdd && tcpreplay && wireshark
Reviewed by: Pavlin Radoslavov
partitioning class that supports multiple schemes. Current
schemes supported are APM (Apple Partition Map) and GPT.
Change all GEOM_APPLE anf GEOM_GPT options into GEOM_PART_APM
and GEOM_PART_GPT (resp).
The ctlreq interface supports verbs to create and destroy
partitioning schemes on a disk; to add, delete and modify
partitions; and to commit or undo changes made.
NOTES though, as ofw_syscons(4) doesn't properly interface with
syscons(4) regarding loading the font specified with SC_DFLT_FONT,
causing a kernel with both options SC_OFWFB and SC_NO_MODE_CHANGE
to not link.
