that we free that resource. All the other resources are freed in
their own routine, but since we haven't saved a pointer to this one,
it is leaked. This is the failure case that lead to the sio ports
that weren't working, I think.
cleared if the host controller retries the transfer and is successful,
but we were interpreting these bits as indicating a fatal error.
Ignore these error bits, and instead use the HALTED bit to determine
if the transfer failed. Also update the USBD_STALLED detection to
ignore these bits.
Obtained from: OpenBSD
between passes over a QH. Previously the accesses to a QH were
bunched together in time, so the interval was often much longer
than intended. This now appears to match the diagrams in the EHCI
spec, so remove the XXX comment.
a serial console anyway because input-device is set to keyboard and
output-device is set to screen but no keyboard is plugged in don't
assume that a device node for the input-device alias exists. While
this is true for RS232 keyboards (the node of the SCC and UART
respectively which controls the keyboard doesn't disappear when no
keyboard is plugged in) this assumption breaks for USB keyboards.
It's most likely also not true for PS/2 keyboards but OFW doesn't
reliably switch to a serial console when the potential keyboard is
a PS/2 one which isn't plugged in so this couldn't be verified
properly.
Reported by: Will Andrews <will@csociety.org>, obrien
MFC after: 1 week
to syncrhonize access to the data as a result. This makes the pps
less likely to miss the 1ms pulse that I'm feeding it, but not
entirely reliable yet on my 133MHz P5.
Reviewed by: phk
unknown (since my sony vaio didn't :-(.
Instead, fix the problem described by 1.49 in a different way: just
add the two calls I'd hoped I'd avoid in 1.49 by doing the (wrong)
gymnastics there. While 1.49 is a good direction to go in, each step
of the way should work :-(.
resources. When allocating 6 ports for a 4 port range isa code
returns an error. I'm not sure yet why this is the case, but suspect
it is just a non-regularity in how the resource allocation code works
which should be corrected. Use 1 as the ports size in this case.
However, in the hints case, we have to specify the length, so use 6 in
that case. I believe that this is also acpi friendly.
Also, complain when we can't allocate FDOUT register space. Right now we
silently fail when we can't. This failure is referred to above.
When there's no resource for FDCTL, go ahead and allocate one by hand.
Many PNPBIOS tables don't list this resource, and our hints mechanism also
doesn't cover that range. If we can't allocate it, whine, but fake up
something. Before, we were always bogusly faking it and no one noticed
the sham (save the original author who has now fixed his private shame).
asks that each buffer be (2048 * 256) bytes long. I suspect that alignment
isn't a real requirement since busdma only recently started honoring it. The
size is also bogus. Fix both of these and stop busdma from trying to
exhaust the system memory pool with bounce pages.
Submitted by: Kevin Oberman
MFC After: 7 days
- Fix a bug in the same condition where we forgot to drop the ACPI pcib
lock. This fixes hangs after the pcib0 attach on some machines.
Tested by: sos (2)
ever working correctly: the code was linking the QHs together but
then immediately overwriting the "next" pointers. Oops. Also
initialise qh_endphub, since the EHCI spec says that we should
always set the pipe multiplier field to something sensible.
This appears to make basic split transactions work, so enable split
transactions for control, bulk and interrupt pipes (split isochronous
transfers are not yet implemented). It should now be possible to
use USB1 devices even when they are connected through a USB2 hub.
from an mbuf into the fxp_encap() function, as done in other drivers.
- Don't waste time calling bus_dmamap_load_mbuf() if we know the mbuf
chain is too long to fit in a TX descriptor, call m_defrag() first.
- Convert fxp(4) to use bus_dmamap_load_mbuf_sg().
at some point result in a status event being triggered (it should
be a link down event: the Microsoft driver design guide says you
should generate one when the NIC is initialized). Some drivers
generate the event during MiniportInitialize(), such that by the
time MiniportInitialize() completes, the NIC is ready to go. But
some drivers, in particular the ones for Atheros wireless NICs,
don't generate the event until after a device interrupt occurs
at some point after MiniportInitialize() has completed.
The gotcha is that you have to wait until the link status event
occurs one way or the other before you try to fiddle with any
settings (ssid, channel, etc...). For the drivers that set the
event sycnhronously this isn't a problem, but for the others
we have to pause after calling ndis_init_nic() and wait for the event
to arrive before continuing. Failing to wait can cause big trouble:
on my SMP system, calling ndis_setstate_80211() after ndis_init_nic()
completes, but _before_ the link event arrives, will lock up or
reset the system.
What we do now is check to see if a link event arrived while
ndis_init_nic() was running, and if it didn't we msleep() until
it does.
Along the way, I discovered a few other problems:
- Defered procedure calls run at PASSIVE_LEVEL, not DISPATCH_LEVEL.
ntoskrnl_run_dpc() has been fixed accordingly. (I read the documentation
wrong.)
- Similarly, the NDIS interrupt handler, which is essentially a
DPC, also doesn't need to run at DISPATCH_LEVEL. ndis_intrtask()
has been fixed accordingly.
- MiniportQueryInformation() and MiniportSetInformation() run at
DISPATCH_LEVEL, and each request must complete before another
can be submitted. ndis_get_info() and ndis_set_info() have been
fixed accordingly.
- Turned the sleep lock that guards the NDIS thread job list into
a spin lock. We never do anything with this lock held except manage
the job list (no other locks are held), so it's safe to do this,
and it's possible that ndis_sched() and ndis_unsched() can be
called from DISPATCH_LEVEL, so using a sleep lock here is
semantically incorrect. Also updated subr_witness.c to add the
lock to the order list.
Change fhc(4) to use IRQ numbers instead of RIDs for allocating the
IRQs of children. This works similar to e.g. sbus(4), i.e. add the
IRQ resources as fully specified to the resource lists of the children,
allocate them like normal. When establishing the interrupt search the
interrupt maps of the children for a matching INO to determine which
map we need to write the fully specified interrupt number to and to
enable the mapping (before the RID was used to indicate which interrupt
map to use).
- dev/puc/puc.c:
Revert rev. 1.38, with the above change fhc(4) no longer needs special
treatment for allocating IRQs.
Thanks to: joerg for providing access to an E3500
modulating the STPCLK# pin based on the duty cycle. Since p4tcc uses the
same mechanism (but internal to the CPU), we triggered a hang on some
systems at low frequencies when both were in use. Now, disable
acpi_throttle when p4tcc is also present.
Tested by: Kevin Oberman
with no associated data. Also revert previous changes that allocate off
of the stack instead of using malloc, as it's not needed. Many thanks to
LSI for investigating and fixing these problems.
Submitted by: rajeshpr @ lsil . com
a vlan interface attached to a fxp(4) card when it has not been
initialized yet. We now set the links from our internel TX descriptor
structure to the TX command blocks at attach time rather than at init
time. While I'm here, slightly improve the style in fxp_attach().
PR: kern/78112
Reported by: Gavin Atkinson <gavin.atkinson@ury.york.ac.uk> and others
Tested by: flz, Gavin Atkinson <gavin.atkinson@ury.york.ac.uk>
MFC after: 1 week
place.
This moves the dependency on GCC's and other compiler's features into
the central sys/cdefs.h file, while the individual source files can
then refer to #ifdef __COMPILER_FEATURE_FOO where they by now used to
refer to #if __GNUC__ > 3.1415 && __BARC__ <= 42.
By now, GCC and ICC (the Intel compiler) have been actively tested on
IA32 platforms by netchild. Extension to other compilers is supposed
to be possible, of course.
Submitted by: netchild
Reviewed by: various developers on arch@, some time ago
