r239274 added support for ranges. Update XLP DTS to provide the correct
range parameter for the XLP SoC bus. Also fix bus_space_map method
for XLP bus space.
Submitted by: Sreekanth M. <sreekanth.molagavalli@broadcom.com>
The last 12 bits of the limit registers have to be set to 1. These
bits are not significant in bridge BARs and are 0 on read, but the
bits are valid in the swap limit register and needs to be set.
The on-chip SD slots do not have PCI BARs corresponding to them, so
this has to be handled in the custom SoC memory allocation.
Provide memory resource for rids corresponding to BAR 0 and 1 in
the custom allocation code.
The XLP on-chip devices have PCI configuration headers, but some of the
devices need custom resource allocation code.
- devices with no MEM/IO BARs with registers in PCIe extended reg
space have to be handled in memory resource allocation
- devices without INTPIN/INTLINE in PCI header can be supported
by having these faked with a shadow register.
- Some devices does not allow 8/16 bit access to the register space,
he default bus space cannot be used for these.
Subclass pci and override attach and resource allocation methods to
take care of this.
Remove earlier code which did this partially.
Move XLP PCI UART device to sys/mips/nlm/dev/ directory. Other
drivers for the XLP SoC devices will be added here as well.
Update uart_cpu_xlp.c and uart_pci_xlp.c use macros for uart port,
speed and IO frequency.
Features:
- network driver for the four 10G interfaces and two management ports
on XLP 8xx.
- Support 4xx and 3xx variants of the processor.
- Source code and firmware building for the 16 mips32r2 micro-code engines
in the Network Accelerator.
- Basic initialization code for Packet ordering Engine.
Submitted by: Prabhath Raman (prabhath at netlogicmicro com)
[refactored and fixed up for style by jchandra]
On XLP evaluation platform, the board information is stored
in an I2C eeprom and the network block configuration is available
from a CPLD connected to the GBU (NOR flash bus). Add support
for both of these.
Support for the Security and RSA blocks on XLP SoC. Even though
the XLP supports many more algorithms, only the ones supported
in OCF have been added.
Submitted by: Venkatesh J. V. (venkatesh at netlogicmicro com)
- XLP supports hardware swap for PCIe IO/MEM accesses. Since we
are in big-endian mode, enable hardware swap and use the normal
bus space.
- move some printfs to bootverbose, and remove others.
- fix SoC device resource allocation code
- Do not use '|' while updating PCIE_BRIDGE_MSI_ADDRL
- some style fixes
In collaboration with: Venkatesh J. V. (venkatesh at netlogicmicro com)
required for the ABI the kernel is being built for.
XXX This is implemented in a kind-of nasty way that involves including source
files, but it's still an improvement.
o) Retire ISA_* options since they're unused and were always wrong.
implementations or no implementation on all platforms.
Some of these functions might be good ideas, but their semantics were unclear
given the lack of implementation, and an unlucky porter could be fooled into
trying to implement them or, worse, being baffled when something like
platform_trap_enter() failed to be called.
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
The dcache flush has to be done using the core control registers before
splitting the L1D cache by enabling the hardware threads.
Also replace .word calls for mfcr/mtcr with a C macro.
In collaboration with: prabhath at netlogicmicro com
* Update message station (CMS) code, read queue ids from PCI header.
* Use interrupts to wakeup message handling threads on 3XX
* Update PIC code, read interrupt information from PCI header instead
of using fixed values.
* Update PCI interrupt handling for the PIC change.
* Update code for getting chip frequency, new code support XLP 3XX
* Misc style(9) fixes
In collaboration with: prabhath at netlogicmicro com (CMS/PIC)
venkatesh at netlogicmicro.com (PCI)
Create std.XLP for configuration options, which is included by the
conf files. The files XLP, XLPN32 and XLP64 will have mostly ABI related
options.
Also move uart and pci to mips/nlm/std.xlp since all XLP configurations
needs these devices.
Obtained from: prabhath at netlogicmicro com (intial version)
- update xlp_machdep.c to read arguments from FDT if FDT support is
compiled in.
- define rmi_uart_bus_space, and use it as fdtbus_bs_tag
- update conf files for FDT support
- add default dts file xlp-basic.dts
* Update the hardware access register definitions and functions to bring
them in line with other Netlogic software.
* Update the platform bus to use PCI even for on-chip devices. Add a dummy
PCI driver to ignore on-chip devices which do not need driver.
* Provide memory and IRQ resource allocation code for on-chip devices
which cannot get it from PCI config.
* add support for on-chip PCI and USB interfaces.
* update conf files, enable pci and retain old MAXCPU until we can support
>32 cpus.
Approved by: re(kib), jmallett
This patch adds support for the Netlogic XLP mips64 processors in
the common MIPS code. The changes are :
- Add CPU_NLM processor type
- Add cases for CPU_NLM, mostly were CPU_RMI is used.
- Update cache flush changes for CPU_NLM
- Add kernel build configuration files for xLP.
In collaboration with: Prabhath Raman <prabhathpr at netlogicmicro com>
Approved by: bz(re), jmallett, imp(mips)
