This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
Change code from PRC_UNREACH_ADMIN_PROHIB to PRC_UNREACH_PORT for
ICMP_UNREACH_PROTOCOL and ICMP_UNREACH_PORT
And let TCP treat PRC_UNREACH_PORT like PRC_UNREACH_ADMIN_PROHIB
This should fix the case where port unreachables for udp returned
ENETRESET instead of ECONNREFUSED
Problem found by: Bill Fenner <fenner@research.att.com>
Reviewed by: jlemon
on certain types of SOCK_RAW sockets. Also, use the ip.ttl MIB
variable instead of MAXTTL constant as the default time-to-live
value for outgoing IP packets all over the place, as we already
do this for TCP and UDP.
Reviewed by: wollman
an IP header with ip_len in network byte order. For certain
values of ip_len, this could cause icmp_error() to write
beyond the end of an mbuf, causing mbuf free-list corruption.
This problem was observed during generation of ICMP redirects.
We now make quite sure that the copy of the IP header kept
for icmp_error() is stored in a non-shared mbuf header so
that it will not be modified by ip_output().
Also:
- Calculate the correct number of bytes that need to be
retained for icmp_error(), instead of assuming that 64
is enough (it's not).
- In icmp_error(), use m_copydata instead of bcopy() to
copy from the supplied mbuf chain, in case the first 8
bytes of IP payload are not stored directly after the IP
header.
- Sanity-check ip_len in icmp_error(), and panic if it is
less than sizeof(struct ip). Incoming packets with bad
ip_len values are discarded in ip_input(), so this should
only be triggered by bugs in the code, not by bad packets.
This patch results from code and suggestions from Ruslan, Bosko,
Jonathan Lemon and Matt Dillon, with important testing by Mike
Tancsa, who could reproduce this problem at will.
Reported by: Mike Tancsa <mike@sentex.net>
Reviewed by: ru, bmilekic, jlemon, dillon
reset TCP connections which are in the SYN_SENT state, if the sequence
number in the echoed ICMP reply is correct. This behavior can be
controlled by the sysctl net.inet.tcp.icmp_may_rst.
Currently, only subtypes 2,3,10,11,12 are treated as such
(port, protocol and administrative unreachables).
Assocaiate an error code with these resets which is reported to the
user application: ENETRESET.
Disallow resetting TCP sessions which are not in a SYN_SENT state.
Reviewed by: jesper, -net
Add new PRC_UNREACH_ADMIN_PROHIB in sys/sys/protosw.h
Remove condition on TCP in src/sys/netinet/ip_icmp.c:icmp_input
In src/sys/netinet/ip_icmp.c:icmp_input set code = PRC_UNREACH_ADMIN_PROHIB
or PRC_UNREACH_HOST for all unreachables except ICMP_UNREACH_NEEDFRAG
Rename sysctl icmp_admin_prohib_like_rst to icmp_unreach_like_rst
to reflect the fact that we also react on ICMP unreachables that
are not administrative prohibited. Also update the comments to
reflect this.
In sys/netinet/tcp_subr.c:tcp_ctlinput add code to treat
PRC_UNREACH_ADMIN_PROHIB and PRC_UNREACH_HOST different.
PR: 23986
Submitted by: Jesper Skriver <jesper@skriver.dk>
were performed to determine if the received packet should be reset. This
created erroneous ratelimiting and false alarms in some cases. The code
has now been reorganized so that the checks for validity come before
the call to badport_bandlim. Additionally, a few changes in the symbolic
names of the bandlim types have been made, as well as a clarification of
exactly which type each RST case falls under.
Submitted by: Mike Silbersack <silby@silby.com>
messages send by routers when they deny our traffic, this causes
a timeout when trying to connect to TCP ports/services on a remote
host, which is blocked by routers or firewalls.
rfc1122 (Requirements for Internet Hosts) section 3.2.2.1 actually
requi re that we treat such a message for a TCP session, that we
treat it like if we had recieved a RST.
quote begin.
A Destination Unreachable message that is received MUST be
reported to the transport layer. The transport layer SHOULD
use the information appropriately; for example, see Sections
4.1.3.3, 4.2.3.9, and 4.2.4 below. A transport protocol
that has its own mechanism for notifying the sender that a
port is unreachable (e.g., TCP, which sends RST segments)
MUST nevertheless accept an ICMP Port Unreachable for the
same purpose.
quote end.
I've written a small extension that implement this, it also create
a sysctl "net.inet.tcp.icmp_admin_prohib_like_rst" to control if
this new behaviour is activated.
When it's activated (set to 1) we'll treat a ICMP administratively
prohibited message (icmp type 3 code 9, 10 and 13) for a TCP
sessions, as if we recived a TCP RST, but only if the TCP session
is in SYN_SENT state.
The reason for only reacting when in SYN_SENT state, is that this
will solve the problem, and at the same time minimize the risk of
this being abused.
I suggest that we enable this new behaviour by default, but it
would be a change of current behaviour, so if people prefer to
leave it disabled by default, at least for now, this would be ok
for me, the attached diff actually have the sysctl set to 0 by
default.
PR: 23086
Submitted by: Jesper Skriver <jesper@skriver.dk>
1. ICMP ECHO and TSTAMP replies are now rate limited.
2. RSTs generated due to packets sent to open and unopen ports
are now limited by seperate counters.
3. Each rate limiting queue now has its own description, as
follows:
Limiting icmp unreach response from 439 to 200 packets per second
Limiting closed port RST response from 283 to 200 packets per second
Limiting open port RST response from 18724 to 200 packets per second
Limiting icmp ping response from 211 to 200 packets per second
Limiting icmp tstamp response from 394 to 200 packets per second
Submitted by: Mike Silbersack <silby@silby.com>
fields between host and network byte order. The details:
o icmp_error() now does not add IP header length. This fixes the problem
when icmp_error() is called from ip_forward(). In this case the ip_len
of the original IP datagram returned with ICMP error was wrong.
o icmp_error() expects all three fields, ip_len, ip_id and ip_off in host
byte order, so DTRT and convert these fields back to network byte order
before sending a message. This fixes the problem described in PR 16240
and PR 20877 (ip_id field was returned in host byte order).
o ip_ttl decrement operation in ip_forward() was moved down to make sure
that it does not corrupt the copy of original IP datagram passed later
to icmp_error().
o A copy of original IP datagram in ip_forward() was made a read-write,
independent copy. This fixes the problem I first reported to Garrett
Wollman and Bill Fenner and later put in audit trail of PR 16240:
ip_output() (not always) converts fields of original datagram to network
byte order, but because copy (mcopy) and its original (m) most likely
share the same mbuf cluster, ip_output()'s manipulations on original
also corrupted the copy.
o ip_output() now expects all three fields, ip_len, ip_off and (what is
significant) ip_id in host byte order. It was a headache for years that
ip_id was handled differently. The only compatibility issue here is the
raw IP socket interface with IP_HDRINCL socket option set and a non-zero
ip_id field, but ip.4 manual page was unclear on whether in this case
ip_id field should be in host or network byte order.
o Drop all broadcast and multicast source addresses in tcp_input.
o Enable ICMP_BANDLIM in GENERIC.
o Change default to 200/s from 100/s. This will still stop the attack, but
is conservative enough to do this close to code freeze.
This is not the optimal patch for the problem, but is likely the least
intrusive patch that can be made for this.
Obtained from: Don Lewis and Matt Dillon.
Reviewed by: freebsd-security
pr_input() routines prototype is also changed to support IPSEC and IPV6
chained protocol headers.
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
respectively logging and dropping ICMP REDIRECT packets.
Note that there is no rate limiting on the log messages, so log_redirect
should be used with caution (preferrably only for debugging purposes).
option not defined the sysctl int value is set to -1 and read-only.
#ifdef KERNEL's added appropriately to wall off visibility of kernel
routines from user code.
Add ICMP_BANDLIM option and 'net.inet.icmp.icmplim' sysctl. If option
is specified in kernel config, icmplim defaults to 100 pps. Setting it
to 0 will disable the feature. This feature limits ICMP error responses
for packets sent to bad tcp or udp ports, which does a lot to help the
machine handle network D.O.S. attacks.
The kernel will report packet rates that exceed the limit at a rate of
one kernel printf per second. There is one issue in regards to the
'tail end' of an attack... the kernel will not output the last report
until some unrelated and valid icmp error packet is return at some
point after the attack is over. This is a minor reporting issue only.
addresses by default.
Add a knob "icmp_bmcastecho" to "rc.network" to allow this
behaviour to be controlled from "rc.conf".
Document the controlling sysctl variable "net.inet.icmp.bmcastecho"
in sysctl(3).
Reviewed by: dg, jkh
Reminded on -hackers by: Steinar Haug <sthaug@nethelp.no>
net.inet.ip.icmp.bmcastecho = 0 by removing the extra check for the
address being a multicast address. The test now relies on the link
layer flags that indicate it was received via multicast. The previous
logic was broken and replied to ICMP echo/timestamp broadcasts even
when the sysctl option disallowed them.
Reviewed by: wollman
potential problems with other automatic-reply ICMPs, but some of them may
depend on broadcast/multicast to operate. (This code can simply be
moved to the `reflect' label to generalize it.)
Don't search for interface addresses matching interface "NULL"
it's likely to cause a page fault..
this can be triggered by the ipfw code rejecting a locally generated
packet (e.g. you decide to make some network unreachable by local users)
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
to TAILQs. Fix places which referenced these for no good reason
that I can see (the references remain, but were fixed to compile
again; they are still questionable).
Move ipip_input() and rsvp_input() prototypes to ip_var.h
Remove unused prototype for rip_ip_input() from ip_var.h
Remove unused variable *opts from rip_output()
*' instead of caddr_t and it isn't optional (it never was). Most of the
netipx (and netns) pr_ctlinput functions abuse the second arg instead of
using the third arg but fixing this is beyond the scope of this round
of changes.
