apply to this file. The correct message is:
throw_rude_remark: Make sure we're holding the config lock before
proceeding. There's no reason to assume that this
has ever happened, but the alternative might be a
double fault.
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
In file included from ../../../dev/vinum/vinumhdr.h:77,
from ../../../dev/vinum/vinum.c:44:
../../../dev/vinum/vinumext.h:165: warning: redundant redeclaration of `setjmp' in same scope
../../../sys/systm.h:96: warning: previous declaration of `setjmp'
../../../dev/vinum/vinummemory.c:44: warning: redundant redeclaration of `longjmp' in same scope
../../../sys/systm.h:97: warning: previous declaration of `longjmp'
vinumhdr.h:80: warning: redundant redeclaration of `vinum_cdevsw'
vinumext.h:239: warning: previous declaration of `vinum_cdevsw'
in each of the following files:
vinum.c, vinumconfig.c, vinumdaemon.c, vinuminterrupt.c, vinumio.c,
vinumioctl.c, vinumlock.c, vinummemory.c, vinumraid5.c, vinumrequest.c,
vinumrevive.c, vinumstate.c, vinumutil.c
requiring fewer header files for userland programs.
Remove the gross debug device/non-debug device hack used to recognize
whether the kernel module was in sync with the userland module.
compiled with debug support. This can be used by userland programs to
recognize which ioctls the module supports.
As a result, remove the gross debug device/non-debug device hack used
to recognize whether the kernel module was in sync with the userland
module.
Replace explicit references to major/minor numbers of vinum
superdevice with the VINUM_SUPERDEV macro written for that purpose.
gets incremented every time the kernel-userland interface changes.
This enables vinum(8) to check for the correct kernel version and to
produce a useful message if it doesn't match.
Requested by: Too many to count.
Move the definitions of struct drive, sd, plex and volume to
vinumobj.h.
Add a new debug flag, DEBUG_LOCKREQS, which logs only lock requests.
with more than one plex, the data will be accessed
multiple times. During this time, userland code could
potentially modify the buffer, thus causing data
corruption. In the case of a multi-plexed volume this
might be cosmetic, but in the case of a RAID-[45] plex it
can cause severe data corruption which only becomes
evident after a drive failure. Avoid this situation by
making a copy of the data buffer before using it.
Note that this solution does not guarantee any particular
content of the buffer, just that it remains unchanged for
the duration of the request.
Suggested by: alfred
Use this instead of DEBUG_LASTREQS to decide whether to log lock
requests.
MFS:
vinumlock: Catch a potential race condition where one process is
waiting for a lock, and between the time it is woken and
it retries the lock, another process gets it and places it
in the first entry in the table.
This problem has not been observed, but it's possible, and
it's easy enough to fix.
Submitted by: tegge
vinumunlock: Catch a real bug capable of hanging a system. When
releasing a lock, vinumunlock() called wakeup_one. This
caused wakeups to sometimes get lost. After due
consideration, we think that this is due to the fact that
you can't guarantee that some other process is also
waiting on the same address. This makes wakeup_one a
very dangerous function to use.
Requested by: bde
Add retryerrors keyword.
vinum_scandisk: Print a different message if an inadvertent start
command did not find any additional drives. The previous message "no
drives found" confused and worried many people.
MFS:
vinum_open: Recognize Mylex devices as storage devices.
In case of error, check the VF_RETRYERRORS flag in the subdisk and
don't take the subdisk down if it's set, just retry the I/O.
Requested by: peter
If the buffer has been copied (XFR_COPYBUF), release the copied
buffer when the I/O completes.
Suggested by: alfred
Desired by: bde
This commit is the first of a general cleanup of the header files..
It won't be enough to make bde happy.
Move debug definitions from vinumhdr.h.
Create a new struct rangelockinfo. In revision 1.21 of vinumlock.c,
the plex info was removed from struct rangelock, since it wasn't
needed there. It *is* needed for trace information, however, so use
struct rangelockinfo for that.
userland tool:
Use the vfs.devfs.generation sysctl to test for devfs presense
(thanks phk!) when devfs is active it will not try to create the
device nodes in /dev and therefore will not complain about the
failure to do so.
Revert the change in the #define for VINUM_DIR in the kernel
header so that vinum can find its device nodes.
Replace perror() with vinum_perror() to print file/line when
DEVBUG is defined (not defined by default).
kernel:
Don't use the #define names for the "superdev" creation since
they will be prepended by "/dev/" (based on VINUM_DIR), instead
use string constants.
Create both debug and non-debug "superdev" nodes in the devfs.
Problem noticed and fix tested by: Martin Blapp <mblapp@fuchur.lan.attic.ch>
remove_sd_entry() to:
Simplify (hopefully) it by moving all error returns closer to
the beginning of the function.
Return an error when "Error removing subdisk %s: not found in
plex %s\n" would have been reported, as I doubt that we are "OK"
after printing that error message.
Adding make_dev() and destroy_dev() calls in (hopefully) the right
places.
This is done by calling make_dev() in each object constructor and
caching the dev_t's returned from make_dev() in each struct
'subdisk'(sd), 'plex' and 'volume' such that the 'object'_free()
functioncs can call destroy dev.
This change makes a subset of the old /dev/vinum appear under devfs.
Enough nodes appear such that I'm able to mount my striped volume.
There may be more work needed to get vinum configuration working
properly.
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
striped plexes. This prevents various panics introduced in the last
rewrite of the locking code.
Suffered by: "Niels Chr. Bank-Pedersen" <ncbp@bank-pedersen.dk>
interrupt threads to run with it always >= 1, so that malloc can
detect M_WAITOK from "interrupt" context. This is also necessary
in order to context switch from sched_ithd() directly.
Reviewed By: peter
not yet been caught), don't save the config with a null drive
name (which causes the drive to be renamed "plex" on the next
start), put in the text "*invalid*" instead.
This is damage control, not a fix.
Experienced by: peter
Break some long format strings so that they fit in style(9)-sized
lines.
Remove some "outdentation".
