to match the pccard.conf file. There are more ID's that need adding, but
these seem to be the common ones.
This was committed on an ep0 interface under NEWCARD:
ep0: <3Com 3c589 10Mbps Ethernet> at port 0x300-0x30f irq 9 function 0 config 1 on pccard1
ep0: Ethernet address 00:10:4b:df:48:57
Reviewed by: imp
possible to have different probe/attach semantics between the two
systems and yet still use the same driver for both.
Compatibility methods for OLDCARD drivers. We use these routines to make
it possible to call the OLDCARD driver's probe routine in the context that
it expects. For OLDCARD these are implemented as pass throughs to the
device_{probe,attach} routines. For NEWCARD they are implemented such
such that probe becomes strictly a matching routine and attach does both
the old probe and old attach.
compat devices should use the following:
/* Device interface */
DEVMETHOD(device_probe), pccard_compat_probe),
DEVMETHOD(device_attach), pccard_compat_attach),
/* Card interface */
DEVMETHOD(card_compat_match, foo_match), /* newly written */
DEVMETHOD(card_compat_probe, foo_probe), /* old probe */
DEVMETHOD(card_compat_attach, foo_attach), /* old attach */
This will allow a single driver binary image to be used for both
OLDCARD and NEWCARD.
Drivers wishing to not retain OLDCARD compatibility needn't do this.
ep driver minorly updated.
sn driver updated more than minorly. Add module dependencies to allow
module to load. Also change name to if_sn. Add some debugging code.
attempt to fix the cannot allocate memory problem I'd been seeing.
Minor formatting nits.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
ifconfig and bogus ethernet address (4b:57:4b:57:4b:57) has been
hacked around. I'll revisit this when I have a clue whats going on.
Reviewed by: obrien
problem.
o Create new timeout routine so we don't detach the card inside a ISR
but instead drop back to spl0 via a timeout of 0.
o Actually delete the child of the pccard device rather than just faking
it badly.
o Fix sio, ed and ep to have pccard detach routines that are int rather
than void.
o Fix ep and ed pccard detach routines to use if_detach rather than just
if_down. if_detach destroys the device, while if_down just marks it
down. In this incarnation of the pccard things, we map the disable
the slot action to detach the driver, which removes the driver from the
device tree. When that is done, a panic would soon follow as the
ifconfig tried to down the device.
Didn't fix:
o Should cache the pccard dev child's pointer in struct slot
o remove now unused parts of struct slot
o Any driver using softc after detach has been called. sio's softc used
to be statically allocated, so you could check sc->gone, but that is
now gone.
o Didn't remove gone from softc of drivers that use the old pccard method.
Didn't test:
o ed driver changes
o sio driver changes on pccards
o suspend (no laptop or apm support on my desktop)
test this support since I don't have the dongle for the card in
question and the dongle I have for my 3C589D doesn't seem to work on
it. I don't know if this is due to the damage I did to the 562 card
in transit from freebsdcon, or a mis-matched dongle...
pccard attachments must activate the resources they want to access.
ep didn't do this, so of course thee eeprom came back as busy. ed and
sio already did this. It was only due to a bug in the logic that the
probe succeeded. These problems have been fixed.
- Rip out all the static softc stuff and do softc allocation the right way.
- Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY
method to enumerate all non-PnP ISA devices.
This has the following consequences:
- No 'ep' devices may be hardwired.
- All hardwired devices will probably be detected twice.
By hardwired I mean:
device ep0 at isa? port 0x300 irq 10
- 'ep' devices are ordered by bus, slot, and then MAC address.
- Make 3c509B cards work in PnP mode. Yes, they really work.
- Convert over to using ifmedia for media selection. No more of this
lame 'linkX' stuff.
- Consolidate a lot of duplicated code.
- Make a stab at not breaking MII based PCCARD devices.
I doubt that the PCCARD stuff works any more than it did before my
changes but theres hope. My PCCARD hardware should arrive in a
week or so.
- Retreive the media settings from the card EEPROM rather than guessing.
I've got a 3c509-TPO that thinks its got an AUI port and if others
can report similar problems I'll write a bit of clever code that will
fix this but right now it works correctly on all but 1 card.
- Clean up a few things and make some cosmetic changes.
- Add myself as the MAINTAINER since nobody else wants to. I'm
in the best position to do this as I've got an example of most
of the cards:
EISA 3c579 bnc/aui
MCA 3c529 tp/aui
ISA 3c509 tpo
ISA-PnP 3c509B combo
If someone wants to send me a any cards I don't have I'd appriciate
it. Also welcome are 3c59x boards since I'll be folding if_vx and
if_ep at some point.
I'm committing this from a laptop running this driver. Have only one
devclass for all ep devices (at least for pccard and eisa) so unit
numbering is sane. Might not work with both isa and non-isa devices
on the same system until ep is updated (Matt has some patches in the
pipeline which should resolve this, he wanted me to commit this so he
can resolve any conflicts against cvs rather than my patches).
Reviewed by: Matt Dodd <mdodd@freebsd.org>
- Split out the prototypes, externs and struct decls from if_epreg.h into
if_epvar.h.
- Add support for MCA based Etherlink III (3c529) devices.
None of this code is used right now; the old if_ep driver is still
in place and used.
I will eventually get around to converting if_ep_isa.c to newbus once I've
had a talk with Peter and DFR about the DEVICE_IDENTIFY() method.
I have tested this code on my PS/2. It works. I would like EISA and ISA
testers since my example hardware hasn't arrived yet.
Add:
dev/ep/if_ep.c optional ep
dev/ep/if_ep_isa.c optional ep isa
dev/ep/if_ep_eisa.c optional ep eisa
dev/ep/if_ep_mca.c optional ep mca
dev/ep/if_ep_pccard.c optional ep card
to sys/conf/files
Remove:
i386/eisa/3c5x9.c optional ep
i386/isa/if_ep.c optional ep
from sys/i386/conf/files.i386
PCCARD testers wanted!
I will switch off and cvs rm the old driver in favor of this copy once
I've had positive feedback or have the hardware to verify that it works.
