not provide any MAC configuration interface for resolved flow
control parameters. There is even no register that configures water
mark which will control generation of pause frames.
However enabling flow control surely enhanced performance a lot.
such that nfe(4) does not work with MSI-X. When MSI-X support was
introduced, I remember MCP55 controller worked without problems so
the issue could be either PCI bridge or BIOS issue. But I also
noticed snd_hda(4) disabled MSI on all MCP55 chipset so I'm still
not sure this is generic issue of MCP55 chipset. If this was PCI
bridge issue we would have added it to a system wide black-list
table but it's not clear to me at this moment whether it was caused
by either broken BIOS or silicon bug of MCP55 chipset.
To workaround the issue, maintain a MSI/MSI-X black-list table in
driver and lookup base board manufacturer and product name from the
table before attempting to use MSI-X. If driver find an matching
entry, nfe(4) will not use MSI/MSI-X and fall back on traditional
INTx mode. This approach should be the last resort since it relies
on smbios and if another instance of MSI/MSI-X breakage is reported
with different maker/product, we may have to get the PCI bridge
black-listed instead of adding an new entry.
PR: kern/152150
K3765 datacard. After ejecting this device, it reappears using
the normal K3765 ID. It does not switch automatically
Reviewed by: n_hibma
Obtained from: OpenBSD
MFC after: 2 weeks
The ports/Mk/bsd.port.mk uses sys/param.h to fetch osrel, and cannot
grok several constants with the prefix.
Reported and tested by: swell.k gmail com
MFC after: 1 week
The unmapped page separates the tip of the stack and possible adjanced
segment, making some uses of stack overflow harder. The stack growing
code refuses to expand the segment to the last page of the reseved
region when sysctl security.bsd.stack_guard_page is set to 1. The
default value for sysctl and accompanying tunable is 0.
Please note that mmap(MAP_FIXED) still can place a mapping right up to
the stack, making continuous region.
Reviewed by: alc
MFC after: 1 week
of certain MAC models from brgphy(4) to bge(4) where it belongs. While at it,
update the list of models having that restriction to what OpenBSD uses, which
in turn seems to have obtained that information from the Linux tg3 driver.
during boot.
Change the last argument of gets() to indicate a visibility flag and add
definitions for the numerical constants. Except for the value 2, gets()
will behave exactly the same, so existing consumers shouldn't break. We
only use it in two places, though.
Submitted by: lme (older version)
annex 31B full duplex flow control as well as the IFM_1000_T master
support committed in r215297. For atphy(4) and jmphy(4) this includes
changing these PHY drivers to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set).
- Rename {atphy,jmphy}_auto() to {atphy,jmphy}_setmedia() as these handle
other media types as well.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
support in mii(4):
- Merge generic flow control advertisement (which can be enabled by
passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
IFM_FLOW isn't implemented as a global option via the "don't care
mask" but instead as a media specific option this. This has the
following advantages:
o allows flow control advertisement with autonegotiation to be
turned on and off via ifconfig(8) with the default typically
being off (though MIIF_FORCEPAUSE has been added causing flow
control to be always advertised, allowing to easily MFC this
changes for drivers that previously used home-grown support for
flow control that behaved that way without breaking POLA)
o allows to deal with PHY drivers where flow control advertisement
with manual selection doesn't work or at least isn't implemented,
like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
by setting MIIF_NOMANPAUSE
o the available combinations of media options are readily available
from the `ifconfig -m` output
- Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
- Change IFM_ETH_MASTER from being implemented as a global option via
the "don't care mask" to a media specific one as it actually is only
applicable to IFM_1000_T to date.
- Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
actually configure manually selected slave mode (like we also do in
the PHY specific implementations).
- Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
e1000phy(4) and ip1000phy(4) to use the generic flow control support
instead of home-grown solutions via IFM_FLAGs. This includes changing
these PHY drivers and smcphy(4) to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
the contents of the BMSR via mii_phy_add_media() instead of hardcoding
them. The latter approach seems to have developed historically, besides
causing unnecessary code duplication it was also undesirable because
brgphy_mii_phy_auto() already based the capability advertisement on the
contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
just BCM5701. Apparently this was a misinterpretation of a workaround
in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
this doesn't mean we can't set these as well on other PHYs for manual
media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
IFM_1000_T master mode support now is generally available with all PHY
drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
not applicable there.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
probe method return BUS_PROBE_NOWILDCARD so it doesn't get attached to real
devices hanging off of nexus(4) with no specific devclass set. Actually, the
more desirable fix for this would be to get rid of the newbus interface of
cryptosoft(4) altogether but apparently crypto(9) was written with support
for cryptographic hardware in mind so that approach would require some KPI
breaking changes which don't seem worth it.
MFC after: 1 week
its internal data. This has been used to bypass missing calls in drivers
which do not use the ratectl framework correctly. Issue is, not all algos
use that variable, or even have internal data, therefore valid calls are
not done. Fix this by removing the checks, all driver issues should be
resolved.
MFC after: 1 week
This is the same change that was made in rev 1.33 of boot/i386/btx/btx/btx.S
PR: i386/91871
Submitted by: Bjorn Konig <bkoenig at cs.tu-berlin.de>
MFC after: 1 week
case to previous panic behavior.
I have a real fix that changes the sg dma tag allocation
to be limited to the under 4GB address space but would
prefer to have review before committing.
mipsel' or 'machine mips mipseb' into the config file (with a few 64's
tossed in for good measure). This will let us build the proper
kernels with different worlds as part of make universe.
and VFS_RELE on a non-existing hold on snapshot parent's z_vfs.
This disables the changes from OpenSolaris onnv-revision 9234:bffdc4fc05c4
(bug IDs: 6792139, 6794830) - not applicable to FreeBSD.
This fixes the process hang if umounting a manually mounted snapshot.
Reported by: Alexander Zagrebin <alexz@visp.ru>
Approved by: delphij (mentor)
MFC after: 1 week
the currently selected rate. The calculations of course need a valid
rate. To make that possible before any call to node_rate() is done,
initialize ni_txrate on none_node_init() calls.
MFC after: 1 week
Bug fixes:
* Fixed "inquiry data fails comparion at DV1 step"
* Fixed bad range input in bus_alloc_resource for ADAPTER_TYPE_B
* Fixed arcmsr driver prevent arcsas support for Areca SAS HBA ARC13x0
Many thanks to Areca for continuing to support FreeBSD.
This commit is intended for MFC before 8.2-RELEASE.
Submitted by: Ching-Lung Huang <ching2048 areca com tw>
bug (incorrect placement of __start_SECNAME in some cases) that was
fixed in r210245.
There is already an UPDATING entry about needing a recent ld.
MFC after: 1 month
When a fast machine first brings up some non TCP networking program
it is quite possible that we will drop packets due to the fact that
only one packet can be held per ARP entry. This leads to packets
being missed when a program starts or restarts if the ARP data is
not currently in the ARP cache.
This code adds a new sysctl, net.link.ether.inet.maxhold, which defines
a system wide maximum number of packets to be held in each ARP entry.
Up to maxhold packets are queued until an ARP reply is received or
the ARP times out. The default setting is the old value of 1
which has been part of the BSD networking code since time
immemorial.
Expose the time we hold an incomplete ARP entry by adding
the sysctl net.link.ether.inet.wait, which defaults to 20
seconds, the value used when the new ARP code was added..
Reviewed by: bz, rpaulo
MFC after: 3 weeks
Move logic of building ACPI headers for acpi_wakeup.c into better places,
remove intermediate makefile and shell script, and reduce diff between i386
and amd64.