the first device entry matching the USB vendor, product and revision
would be searched for quirks. After this patch all device entries will
be searched for quirks.
MFC after: 1 week
urtwn_set_rx_bssid_all() will allow to receive beacons only
when they are not denied by filter.
Revealed by D5474.
Tested with RTL8188CUS, HOSTAP mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5477
requesting the initial complete device descriptor and not as part of
the subsequent babble error recovery. Babble means that the received
USB packet was bigger than than configured maximum packet size. This
only affects enumeration of FULL speed USB devices which use a
bMaxPacketSize different from 8 bytes. This patch might help fix
enumeration of USB devices which exhibit USB I/O errors in dmesg
during boot.
MFC after: 1 week
- Add URTWN_WITHOUT_UCODE option (will disable any firmware specific code
when set).
- Do not exclude the driver from build when MK_SOURCELESS_UCODE is set
(URTWN_WITHOUT_UCODE will be enforced unconditionally).
- Do not abort initialization when firmware cannot be loaded;
behave like the URTWN_WITHOUT_UCODE option was set.
- Drop some unused variables from urtwn_softc structure.
Tested with RTL8188EU and RTL8188CUS in HOSTAP and STA modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4849
Use driver settable callbacks for handling of:
- core post reset
- reading actual port speed
Typically, OTG enabled EHCI cores wants setting of USBMODE register,
but this register is not defined in EHCI specification and different
cores can have it on different offset.
Also, for cores with TT extension, actual port speed must be determinable.
But again, EHCI specification not covers this so this patch provides
function for two most common variant of speed bits layout.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D5088
Redo LC calibration if temperature changed significantly since last
calibration.
Tested with RTL8188EU/RTL8188CUS in STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Obtained from: NetBSD (mostly)
Differential Revision: https://reviews.freebsd.org/D4966
- Use bitmap for debug output selection.
- Add few new messages (one for URTWN_DEBUG_BEACON
and another one for URTWN_DEBUG_INTR).
- Replace an undocumented URTWN_DEBUG definition with USB_DEBUG.
Tested with RTL8188EU / RTL8188CUS in IBSS / HOSTAP modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4959
(by default it was set to 9us).
Tested with RTL8188EU / RTL8188CUS in STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4535
Driver was modified to ensure it attaches properly to "marvell,orion-ehci"
node, which doesn't have error interrupt line defined. Neccessary
ofw_compat_data struct was added and probe procedure was altered.
Reviewed by: andrew, ian
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4369
Previously the polarity was for TTL levels, which are the reverse of RS-232.
Also add handling of the UART_PPS_INVERT_PULSE option bit in the sysctl
value, the same as was recently added to uart(4), so that people using TTL
level connections can request a logical inverting of the signal.
Use the named constants from the new dev/uart/uart_ppstypes.h for the pps
capture modes and option bits.
- Add the structure with already known fields offsets
(some of them were taken from this driver,
some (channel_plan, rf_* fields) - from TP-LINK official driver)
- Fix a typo / dehardcode a constant in RTL8192C ROM structure.
Tested with RTL8188EU, STA mode
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4274
available. As with MSI interrupts these can be disabled by setting
hw.usb.xhci.msix to 0 in the loader.
MSI-X interrupts are needed on some hardware, for example the Cavium
ThunderX only supports them, and with this we don't fall back to polling.
PR: 204378
Reviewed by: hselasky, jhb
MFC after: 1 week (after r292669)
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D4698
Tested with RTL8188EU and RTL8188CUS in STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4523
Currently, in case when npkts >= 2, RSSI and Rx radiotap fields
will be overridden by the next packet. As a result, every packet
from this chain will use the same RSSI / radiotap data.
After this change, RSSI and radiotap structure will be filled
for every frame right before ieee80211_input() call.
Tested with RTL8188EU / RTL8188CUS, STA and MONITOR modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4487
An implementation from rum(4) was used (it looks simpler for me).
Will be used for h/w encryption support.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4447
- Add IEEE80211_GET_SLOTTIME(ic) macro.
- Use predefined macroses to set slot time.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4044
tables. Some drivers needed some slight re-arrangement of declarations
to accommodate this. Change the USB pnp tables slightly to allow
better compatibility with the system by moving linux driver info from
start of each entry to the end. All other PNP tables in the system
have the per-device flags and such at the end of the elements rather
that at the beginning.
Differential Review: https://reviews.freebsd.org/D3458
from 1500 to 1496 bytes. The MTU should remain at 1500, extending the
frame size as per IEEE 802.3. Adding IFCAP_VLAN_MTU to the
if_capabilities field in the smsc driver solves the problem. The
datasheet for the LAN9512 chip, section 3.2.3 states that the chip
supports the extended frame.
Submitted by: rpp@ci.com.au
MFC after: 1 week
PR: 205050
- Restore R92C_TXDW4_HWSEQ_EN bit - it is used by non-8188EU chips.
- Fix DRVRATE bit usage.
Tested with:
- RTL8188EU, STA mode.
- RTL8188CUS, STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4352
IPv4/IPv6 checksum offloading and VLAN tag insertion/stripping.
Since uether doesn't provide a way to announce driver specific offload
capabilities to upper stack, checksum offloading support needs more work
and will be done in the future.
Special thanks to Hayes Wang from RealTek who gave input.
- Add error handling for urtwn_(r88e_)read_rom() and
urtwn_efuse_*() functions.
- Remove code duplication between urtwn_efuse_read() and
urtwn_r88e_read_rom().
- Merge r88e_rom and (r92c_)rom structures
(only one of them can be used at the same time).
- Other minor fixes / improvements.
Tested with RTL8188EU, STA mode
(URTWN_DEBUG + USB_DEBUG, hw.usb.urtwn.debug=3, no visual differences).
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4253
- Split urtwn_tx_start() into urtwn_tx_data() and urtwn_tx_start()
(the last will be used for beacon updates / raw xmit path).
- Remove unneeded code from _urtwn_getbuf().
- Use CCK11 for data frames in 11b mode.
- Send EAPOL frames at 1 Mbps.
- Reduce code duplication in urtwn_tx_data().
- Fix sequence numbering.
- Add IEEE80211_RADIOTAP_F_WEP flag for encrypted frames.
- Check URTWN_RUNNING flag under lock.
Tested with RTL8188EU, STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4017
- Filter out unneeded frames in STA mode.
- Implement ic_promisc() call.
Tested with RTL8188EU, STA and MONITOR modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D3999
32-bits aligned. Merge the two bounce buffers into a single one. Some
rough tests showed that the DWC OTG throughput on RPI2 increased by
10% after this patch.
MFC after: 1 week
The mbuf length fields must be set before m_adj() is called else
m_adj() will not always adjust the mbuf and an unaligned read
exception can trigger inside the network stack. This can happen on
platforms where unaligned reads are not supported. Adjust a length
check to include the 2-byte ethernet alignment while at it.
MFC after: 3 days
- Drop TSF initialization; device can discover it without our help.
- Do not touch R92C_BCN_CTRL_EN_BCN bit in STA mode.
- Add 'static' keyword for function definition.
Tested with RTL8188EU, STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D3801
Since r288350, ic_wme_task() is called via ieee80211_runtask(),
so, any additional deferring from the driver side is not needed.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4072
status registers for every interrupt. Check a common host channel
status interrupt register first, then conditionally read the
individual host channel status registers.
Submitted by: Sebastian Huber <sebastian.huber@embedded-brains.de>
MFC after: 1 week
- Move all files related to the LinuxKPI into sys/compat/linuxkpi and
its subfolders.
- Update sys/conf/files and some Makefiles to use new file locations.
- Added description of COMPAT_LINUXKPI to sys/conf/NOTES which in turn
adds the LinuxKPI to all LINT builds.
- The LinuxKPI can be added to the kernel by setting the
COMPAT_LINUXKPI option. The OFED kernel option no longer builds the
LinuxKPI into the kernel. This was done to keep the build rules for
the LinuxKPI in sys/conf/files simple.
- Extend the LinuxKPI module to include support for USB by moving the
Linux USB compat from usb.ko to linuxkpi.ko.
- Bump the FreeBSD_version.
- A universe kernel build has been done.
Reviewed by: np @ (cxgb and cxgbe related changes only)
Sponsored by: Mellanox Technologies
registers (they are used for different purposes).
- Wrap R92C_MSR modifications into urtwn_set_mode().
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D3838
This doesn't free the mbuf upon error; the driver ic_raw_xmit method is still
doing that.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3774
* Create ieee80211_free_mbuf() which frees a list of mbufs.
* Use it in the fragment transmit path and ath / uath transmit paths.
* Call it in xmit_pkt() if the transmission fails; otherwise fragments
may be leaked.
This should be a big no-op.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3769
Now run(4) fetches parameters from ic->ic_wme.wme_params array, which is never initialized
(and can be safely removed). This patch replaces &ic->ic_wme.wme_params with
&ic->ic_wme.wme_chanParams.cap_wmeParams (contains parameters for local station;
used by other drivers with WME support).
Tested:
* me: STA: run0: MAC/BBP RT5390 (rev 0x0502), RF RT5370 (MIMO 1T1R), address 38:83:45:11:78:ae
Now device will use retry limit, which is set via 'ifconfig <interface>
maxretry <number>'.
Tested:
* Tested on WUSB54GC, STA mode.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3689
