The controller is commonly found on DM&P Vortex86 x86 SoC. The
driver supports all hardware features except flow control. The
flow control was intentionally disabled due to silicon bug.
DM&P Electronics, Inc. provided all necessary information including
sample board to write driver and answered many questions I had.
Many thanks for their support of FreeBSD.
H/W donated by: DM&P Electronics, Inc.
categories: Those which can't build with PAE because they attempt to cast
a pointer to a bus_addr_t (mostly scsi drivers); and those which can't be
built with XEN because they conflict with something in xen-os.h (e.g., in
cxgb there is a conflicting definition of test_and_clear_bit).
MFC after: 1 week
zones for each malloc bucket size. The purpose is to isolate
different malloc types into hash classes, so that any buffer overruns
or use-after-free will usually only affect memory from malloc types in
that hash class. This is purely a debugging tool; by varying the hash
function and tracking which hash class was corrupted, the intersection
of the hash classes from each instance will point to a single malloc
type that is being misused. At this point inspection or memguard(9)
can be used to catch the offending code.
Add MALLOC_DEBUG_MAXZONES=8 to -current GENERIC configuration files.
The suggestion to have this on by default came from Kostik Belousov on
-arch.
This code is based on work by Ron Steinke at Isilon Systems.
Reviewed by: -arch (mostly silence)
Reviewed by: zml
Approved by: zml (mentor)
systems with PnP/ACPI not reporting i8254 timer. In some cases it can be
fatal, as i8254 can be the only available time counter hardware. From other
side we are now heavily depend on i8254 timer and till the last time it's
init/usage was completely hardcoded. So this change just restores previous
behavior in more regular fashion.
It has more features than acpi_aiboost(4) and it will eventually replace
acpi_aiboost(4).
Submitted by: Constantine A. Murenin <cnst at FreeBSD.org>
Reviewed by: freebsd-acpi, imp
MFC after: 1 month
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
that we support I486 and I586 CPUs in the GENERIC kernel, users wants these
support would have to build a custom kernel to explicitly disable SSE
anyways.
MFC after: 1 month
COMPAT_43TTY enables the sgtty interface. Even though its exposure has
only been removed in FreeBSD 8.0, it wasn't used by anything in the base
system in FreeBSD 5.x (possibly even 4.x?). On those releases, if your
ports/packages are less than two years old, they will prefer termios
over sgtty.
the 'debugging' section of any HEAD kernel and enable for the mainstream
ones, excluding the embedded architectures.
It may, of course, enabled on a case-by-case basis.
Sponsored by: Sandvine Incorporated
Requested by: emaste
Discussed with: kib
sys/conf/makeLINT.mk to only do certain things for certain
architectures.
Note that neither arm nor mips have the Makefile there, thus
essentially not (yet) supporting LINT. This would enable them
do add special treatment to sys/conf/makeLINT.mk as well chosing
one of the many configurations as LINT.
This is a hack of doing this and keeping it in a separate commit
will allow us to more easily identify and back it out.
Discussed on/with: arch, jhb (as part of the LINT-VIMAGE thread)
MFC after: 1 month
The hardware is compliant with WDRT specification, so I originally
considered including generic WDRT watchdog support, but decided
against it, because I couldn't find anyone to the code for me.
WDRT seems to be not very popular.
Besides, generic WDRT porbably requires a slightly different driver
approach.
Reviewed by: des, gavin, rpaulo
MFC after: 3 weeks
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
MFC after: 6 weeks
- Add vesa kernel options for amd64.
- Connect libvgl library and splash kernel modules to amd64 build.
- Connect manual page dpms(4) to amd64 build.
- Remove old vesa/dpms files.
Submitted by: paradox <ddkprog yahoo com> [1], swell k at gmail.com
(with some minor tweaks)
has proven to have a good effect when entering KDB by using a NMI,
but it completely violates all the good rules about interrupts
disabled while holding a spinlock in other occasions. This can be the
cause of deadlocks on events where a normal IPI_STOP is expected.
* Adds an new IPI called IPI_STOP_HARD on all the supported architectures.
This IPI is responsible for sending a stop message among CPUs using a
privileged channel when disponible. In other cases it just does match a
normal IPI_STOP.
Right now the IPI_STOP_HARD functionality uses a NMI on ia32 and amd64
architectures, while on the other has a normal IPI_STOP effect. It is
responsibility of maintainers to eventually implement an hard stop
when necessary and possible.
* Use the new IPI facility in order to implement a new userend SMP kernel
function called stop_cpus_hard(). That is specular to stop_cpu() but
it does use the privileged channel for the stopping facility.
* Let KDB use the newly introduced function stop_cpus_hard() and leave
stop_cpus() for all the other cases
* Disable interrupts on CPU0 when starting the process of APs suspension.
* Style cleanup and comments adding
This patch should fix the reboot/shutdown deadlocks many users are
constantly reporting on mailing lists.
Please don't forget to update your config file with the STOP_NMI
option removal
Reviewed by: jhb
Tested by: pho, bz, rink
Approved by: re (kib)
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
More applications (including Firefox) seem to depend on this nowadays,
so not having this enabled by default is a bad idea.
Proposed by: miwi
Patch by: Florian Smeets <flo kasimir com>
Approved by: re (kib)
* Driver for ACPI HP extra functionations, which required
ACPI WMI driver.
Submitted by: Michael <freebsdusb at bindone.de>
Approved by: re
MFC after: 2 weeks
In the past there have been some reports of PRINTF_BUFR_SIZE not
functioning correctly. Instead of having garbled console messages, we
should just see whether the issues are still there and analyze them.
Approved by: re
controller. These controllers are also known as L1C(AR8131) and
L2C(AR8132) respectively. These controllers resembles the first
generation controller L1 but usage of different descriptor format
and new register mappings over L1 register space requires a new
driver. There are a couple of registers I still don't understand
but the driver seems to have no critical issues for performance and
stability. Currently alc(4) supports the following hardware
features.
o MSI
o TCP Segmentation offload
o Hardware VLAN tag insertion/stripping
o Tx/Rx interrupt moderation
o Hardware statistics counters(dev.alc.%d.stats)
o Jumbo frame
o WOL
AR8131/AR8132 also supports Tx checksum offloading but I disabled
it due to stability issues. I'm not sure this comes from broken
sample boards or hardware bugs. If you know your controller works
without problems you can still enable it. The controller has a
silicon bug for Rx checksum offloading, so the feature was not
implemented.
I'd like to say big thanks to Atheros. Atheros kindly sent sample
boards to me and answered several questions I had.
HW donated by: Atheros Communications, Inc.
goal of shipping 8.0 with MAC support in the default kernel. No policies
will be compiled in or enabled by default, but it will now be possible to
load them at boot or runtime without a kernel recompile.
While the framework is not believed to impose measurable overhead when no
policies are loaded (a result of optimization over the past few months in
HEAD), we'll continue to benchmark and optimize as the release approaches.
Please keep an eye out for performance or functionality regressions that
could be a result of this change.
Approved by: re (kensmith)
Obtained from: TrustedBSD Project
- Remove vga0 and the disabled uart2/uart3 hints from both platforms.
- Remove hints for ISA adv0, bt0, aha0, aic0, ed0, cs0, sn0, ie0, fe0, and
le0 from i386. All these hints were marked 'disabled' and thus already
did not work "out of the box".
Discussed with: imp
as well as providing stateful load balancing when used with RADIX_MPATH.
- Currently compiled in to i386 and amd64 but disabled by default, it can be enabled at
runtime with 'sysctl net.inet.flowtable.enable=1'.
- Embedded users can remove it entirely from the kernel by adding 'nooption FLOWTABLE' to
their kernel config files.
- A minimal hookup will be added to ip_output in a subsequent commit. I would like to see
more review before bringing in changes that require more churn.
Supported by: Bitgravity Inc.
naming of the partitions (GEOM_PART_EBR_COMPAT). When
compatibility is enabled, changes to the partitioning are
disallowed.
Remove the device name aliasing added previously to provide
backward compatibility, but which in practice doesn't give
us anything.
Enable compatibility on amd64 and i386.
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
in FreeBSD 5.x to allow network device drivers to run with Giant
despite the network stack being Giant-free. This significantly
simplifies calls into ioctl() on network interfaces, especially
in the multicast code, as well as eliminates deferred invocation
of interface if_start routines.
Disable the build on device drivers still depending on
IFF_NEEDSGIANT as they no longer compile. They will be removed
in a few weeks if they haven't been made MPSAFE in that time.
Disabled drivers:
if_ar
if_axe
if_aue
if_cdce
if_cue
if_kue
if_ray
if_rue
if_rum
if_sr
if_udav
if_ural
if_zyd
Drivers that were already disabled because of tty changes:
if_ppp
if_sl
Discussed on: arch@
- leave pmtimer comment that is common to other architectures.
- bring pbio explanation to the block comment relating to other
drivers in the same block.
global NOTES file.
cx(4) driver isn't present in this file, though it could be. However, cx(4)
seems to be more or less dead -- it hasn't been linked to the modules build,
and after TTY-ng transformations it doesn't compile.
Remove it until cx(4) is broken.
- correct format strings
- fill opt_agp.h if AGP_DEBUG is defined
- bring AGP_DEBUG to LINT by mentioning it in NOTES
This should hopefully fix a warning that was...
Found by: Coverity Prevent(tm)
CID: 3676
Tested on: amd64, i386
- add a reference to the config(5) manpage;
- hopefully clarify the format of the 'env FILENAME' directive.
I am putting these notes in sys/${arch}/conf/GENERIC and not
in sys/conf/NOTES because:
1. i386/GENERIC already had reference to a similar option (hints..)
and to documentation (handbook)
2. GENERIC is what most users look at when they have to modify or
create a new kernel config, so having the suggestion there is
more effective.
I am only touching i386 and amd64 because the other GENERIC files
are already out of sync, and I am not sure what is the overall plan.
MFC after: 3 days
to GENERIC configuration files. This brings what's in 8.x in sync
with what is in 7.x, but does not change any current defaults.
Possibly they should now be enabled in head by default?
Log:
- merge in latest xenbus from dfr's xenhvm
- fix race condition in xs_read_reply by converting tsleep to mtx_sleep
Log:
unmask evtchn in bind_{virq, ipi}_to_irq
Log:
- remove code for handling case of not being able to sleep
- eliminate tsleep - make sleeps atomic
Sgtty is a programming interface that has been replaced by termios over
the years. In June we already removed <sgtty.h>, which exposes the
ioctl()'s that are implemented by this interface. The importance of this
flag is overrated right now.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
controller. The controller is also known as L1E(AR8121) and
L2E(AR8113/AR8114). Unlike its predecessor Attansic L1,
AR8121/AR8113/AR8114 uses completely different Rx logic such that
it requires separate driver. Datasheet for AR81xx is not available
to open source driver writers but it shares large part of Tx and
PHY logic of L1. I still don't understand some part of register
meaning and some MAC statistics counters but the driver seems to
have no critical issues for performance and stability.
The AR81xx requires copy operation to pass received frames to upper
stack such that ale(4) consumes a lot of CPU cycles than that of
other controller. A couple of silicon bugs also adds more CPU
cycles to address the known hardware bug. However, if you have fast
CPU you can still saturate the link.
Currently ale(4) supports the following hardware features.
- MSI.
- TCP Segmentation offload.
- Hardware VLAN tag insertion/stripping with checksum offload.
- Tx TCP/UDP checksum offload and Rx IP/TCP/UDP checksum offload.
- Tx/Rx interrupt moderation.
- Hardware statistics counters.
- Jumbo frame.
- WOL.
AR81xx PCIe ethernet controllers are mainly found on ASUS EeePC or
P5Q series of ASUS motherboards. Special thanks to Jeremy Chadwick
who sent the hardware to me. Without his donation writing a driver
for AR81xx would never have been possible. Big thanks to all people
who reported feedback or tested patches.
HW donated by: koitsu
Tested by: bsam, Joao Barros <joao.barros <> gmail DOT com >
Jan Henrik Sylvester <me <> janh DOT de >
Ivan Brawley < ivan <> brawley DOT id DOT au >,
CURRENT ML
compiled into the main AMR driver. It's code that is nice to have but not
required for normal operation, and it is reported to cause problems for some
people.
This was located in the ubsa driver, but should be moved into a separate
driver:
- 3G modems provide multiple serial ports to allow AT commands while the PPP
connection is up.
- 3G modems do not provide baud rate or other serial port settings.
- Huawei cards need specific initialisation.
- ubsa is for Belkin adapters, an Linuxy choice for another device like 3G.
Speeds achieved here with a weak signal at best is ~40kb/s (UMTS). No spooky
STALLED messages as well.
Next: Move over all entries for Sierra and Novatel cards once I have found
testers, and implemented serial port enumeration for Sierra (or rather have
Andrea Guzzo do it). They list all endpoints in 1 iface instead of 4 ifaces.
Submitted by: aguzzo@anywi.com
MFC after: 3 weeks
so the benefit of having acpi.ko as a standalone module is outweighed by
the complications of drivers compiled into the kernel not including ACPI
attachments by default.
Discussed on: current
The last half year I've been working on a replacement TTY layer for the
FreeBSD kernel. The new TTY layer was designed to improve the following:
- Improved driver model:
The old TTY layer has a driver model that is not abstract enough to
make it friendly to use. A good example is the output path, where the
device drivers directly access the output buffers. This means that an
in-kernel PPP implementation must always convert network buffers into
TTY buffers.
If a PPP implementation would be built on top of the new TTY layer
(still needs a hooks layer, though), it would allow the PPP
implementation to directly hand the data to the TTY driver.
- Improved hotplugging:
With the old TTY layer, it isn't entirely safe to destroy TTY's from
the system. This implementation has a two-step destructing design,
where the driver first abandons the TTY. After all threads have left
the TTY, the TTY layer calls a routine in the driver, which can be
used to free resources (unit numbers, etc).
The pts(4) driver also implements this feature, which means
posix_openpt() will now return PTY's that are created on the fly.
- Improved performance:
One of the major improvements is the per-TTY mutex, which is expected
to improve scalability when compared to the old Giant locking.
Another change is the unbuffered copying to userspace, which is both
used on TTY device nodes and PTY masters.
Upgrading should be quite straightforward. Unlike previous versions,
existing kernel configuration files do not need to be changed, except
when they reference device drivers that are listed in UPDATING.
Obtained from: //depot/projects/mpsafetty/...
Approved by: philip (ex-mentor)
Discussed: on the lists, at BSDCan, at the DevSummit
Sponsored by: Snow B.V., the Netherlands
dcons(4) fixed by: kan
found in Soekris hardware, for instance). The hardware supports acceleration
of AES-128-CBC accessible through crypto(4) and supplies entropy to random(4).
TODO:
o Implement rndtest(4) support
o Performance enhancements
Submitted by: Patrick Lamaizière <patfbsd -at- davenulle.org>
Reviewed by: jhb, sam
MFC after: 1 week
