(implemented by ffs_reallocblks_ufs[12]) relocates the file's blocks
so as to cluster them together into a contiguous set of blocks on
the disk.
When the cluster crosses the boundary into the first indirect block,
the first indirect block is initially allocated in a position
immediately following the last direct block. Block reallocation
would usually destroy locality by moving the indirect block out of
the way to keep the data blocks contiguous. This change compensates
for this problem by noting that the first indirect block should be
left immediately following the last direct block. It then tries
to start a new cluster of contiguous blocks (referenced by the
indirect block) immediately following the indirect block.
We should also do this for other indirect block boundaries, but it
is only important for the first one.
Suggested by: Bruce Evans
MFC: 2 weeks
give rwlock(9) the ability to crunch different type of structures, with
the only constraint that they have a lock cookie named rw_lock.
This name, then, becames reserved from the struct that wants to use
the rwlock(9) KPI and other locking primitives cannot reuse it for
their members.
Namely such structs are the current struct rwlock and the new struct
rwlock_padalign. The new structure will define an object which has the
same layout of a struct rwlock but will be allocated in areas aligned
to the cache line size and will be as big as a cache line.
For further details check comments on above mentioned revisions.
Reviewed by: jimharris, jeff
* introduce a new HAL API method to pull out the TX status descriptor
contents.
* Add num_delims to the 11n first aggr method. This isn't used by the
driver at the moment so it won't affect anything.
command properly. Without this change, mfi(4) always sends 10 byte READ
and WRITE commands, which will cause data corruption when device is
larger than 2^32 sectors.
PR: kern/173291
Submitted by: Steven Hartland <steven.hartland multiplay.co.uk>
Reviewed by: mav
MFC after: 2 weeks
the previous diradd had already finished it could have been reclaimed
already. This would only happen under heavy dependency pressure.
Reported by: Andrey Zonov <zont@FreeBSD.org>
Discussed with: mckusick
MFC after: 1 week
was still possible to open for write from the lower filesystem. There
is a symmetric situation where the binary could already has file
descriptors opened for write, but it can be executed from the nullfs
overlay.
Handle the issue by passing one v_writecount reference to the lower
vnode if nullfs vnode has non-zero v_writecount. Note that only one
write reference can be donated, since nullfs only keeps one use
reference on the lower vnode. Always use the lower vnode v_writecount
for the checks.
Introduce the VOP_GET_WRITECOUNT to read v_writecount, which is
currently always bypassed to the lower vnode, and VOP_ADD_WRITECOUNT
to manipulate the v_writecount value, which manages a single bypass
reference to the lower vnode. Caling the VOPs instead of directly
accessing v_writecount provide the fix described in the previous
paragraph.
Tested by: pho
MFC after: 3 weeks
all supported debugging bits.
- If DRM_DEBUG_DEFAULT_ON isn't defined, then initialize drm_debug_flag
to zero.
DRM_DEBUG_DEFAULT_ON is defined when module is build with -DDEBUG_DRM
or if kernel config has 'options DEBUG_DRM'.
Reviewed by: kib
Instead, add protocol specific mbuf flags M_IP_NEXTHOP and
M_IP6_NEXTHOP. Use them to indicate that the mbuf's chain
contains the PACKET_TAG_IPFORWARD tag. And do a tag lookup
only when this flag is set.
Suggested by: andre
Add software mixer table for FastTrack Ultra.
Only set volume controls which are valid at startup for standard
USB audio devices, so that settings like treble and bass use
the reset defaults.
MFC after: 1 week
PCM API doesn't support showing all the knobs. Make sure all the USB audio
mixer nodes are freed at detach. Before this patch USB audio would leak
some memory at detach. Print out buffer sizes in number of samples at attach.
Fix setting of volume controls when the number of channels is greater than two.
MFC after: 1 week
the call to pmap_remove_all() within vm_page_cache() is usually redundant.
This change eliminates that call to pmap_remove_all() and introduces a
call to pmap_remove_all() before vm_page_cache() in the one place where
it didn't already exist.
When iterating over a paging queue, if the object containing the current
page has a zero reference count, then the page can't have any managed
mappings. So, a call to pmap_remove_all() is pointless.
Change a panic() call in vm_page_cache() to a KASSERT().
MFC after: 6 weeks
%gs, when supported. Note that WRFSBASE and WRGSBASE are not very
useful on FreeBSD right now, because a return from the kernel mode to
userspace reloads the bases specified by the sysarch(2) syscall, most
likely.
Enable the Supervisor Mode Execution Prevention (SMEP) when
supported. Since the loader(8) performs hand-off to the kernel with
the page tables which contradict the SMEP, postpone enabling the SMEP
on BSP until pmap switched for the proper kernel tables.
Debugged with the help from: avg
Tested by: avg, Michael Moll <kvedulv@kvedulv.de>
MFC after: 1 month
introduced with the IvyBridge CPUs. Provide the definitions for new
bits in CR3 and CR4 registers.
Tested by: avg, Michael Moll <kvedulv@kvedulv.de>
MFC after: 2 weeks
removed in r99417. bge(4) controllers can do TCP checksum offload
for IP fragmented datagrams but unlike ti(4), it lacks UDP checksum
offloading for IP fragmented datagrams. The problem was bge(4)
blindly requested TCP/UDP checksum for IP fragmented datagrams such
that it resulted in corrupted UDP datagrams before r99417.
Remove remaining code for TCP checksum offloading for IP fragmented
datagrams which should have been removed in r99417.
datagrams. Traditionally upper stack fragmented packets without
computing TCP/UDP checksum and these datagrams were passed to
driver. But there are chances that other packets slip into the
interface queue in SMP world. If this happens firmware running on
MIPS 4000 processor in the controller would see mixed packets and
it shall send out corrupted packets.
While I'm here simplify checksum offloading setup.
MFC After: 1 week
Allow textdumps to be called explicitly from DDB.
If "dump" is called in DDB and textdumps are enabled then abort the
dump and tell the user to turn off textdumps.
Add options TEXTDUMP_PREFERRED to turn textdumps on by default.
Add options TEXTDUMP_VERBOSE to be a bit more verbose while textdumping.
Reviewed by: rwatson
MFC after: 2 weeks
port connected to the Broadcom switch does not seem operable, but it's unclear
if that's simply due to a lack of configuration information for the switch.
The switch does not seem to present any identifying information via MDIO,
and is a BCM56512.
(interrupt). All other ATA PIO commands transfer one sector or 512 bytes
at one time. Hardcode these exceptions in ata(4) with ATA_CAM option.
This fixes timeout of READ LOG EXT command used by `smartctl -x /dev/adaX`.
- Testing TSO6 has led me to discover that HW RSC is
a problematic feature, it is ONLY designed to work
with IPv4 in the first place, and if IP forwarding
is done it can't be disabled as LRO in the stack,
also initial testing we've done at Intel shows an
equal performance using TSO[46] on the TX and LRO
on RX, if you ran older code on 82599 or later hardware
you actually could have detrimental performance for
this reason. So I am disabling the feature by default
and all our adapters will now use LRO instead.
- If you have flow control off and multiple queues it
was possible when the buffer of one queue becomes
full that all RX movement is stalled, to eliminate
this problem a feature bit is now set that will allow
packets to be dropped when full rather than stall.
Note, the default is to have flow control on, and this
keeps this from happening.
- Because of the recent fixes in the stack, LRO is now
auto-disabled when problematic, so I have decided to
enable it by default in the capabilities in the driver.
- There are some 1G modules used by some customers, a couple
small tweaks to properly support those in the media code.
- A note: we have now done some testing of TSO6 and using
LRO with IPv6 and it all works great!! Seeing line rate
in both directions in best cases. Thanks bz for your
excellent work!!
current CPU and not always CPU 0.
This has the added benefit of reducing a huge amount of spinlock
contention on the callout_cpu spinlock for CPU 0.
Sponsored by: Intel
if unused in that configuration mixer at NID 15 is muted. Probably CODEC
incorrectly reports its internal connections. Hide that muter from the
driver to avoid muting and make built-in speaker work.
There are several different CODECs sharing this ID and I have not enough
information about them and the bug to implement more universal solution.
Tested by: Big Yuuta <init.py@gmail.com>
MFC after: 2 weeks
* Add some more ANI spur immunity levels.
* For AR5111 radios attached to an AR5212, limit the 5GHz channels
that are available. A later revision of the AR5111 supports the 4.9GHz
PSB channels but right now there's no check in place for the radio
revision.
If someone wants PSB support on AR5212+AR5111 radios then please let
me know and I'll add the relevant version check.
Obtained from: Qualcomm Atheros
the internet as "AR9380 and later which didn't get its PCI ID written
in at power-on", so it's hardly an unknown constant.
Obtained from: Qualcomm Atheros
this was designed to keep duplicate null vlan tags from
being added. When doing vlans purely via the switch
this problem will occur. Reported by external customer.
cache line in order to avoid manual frobbing but using
struct mtx_padalign.
The sole exception being nvme and sxfge drivers, where the author
redefined CACHE_LINE_SIZE manually, so they need to be analyzed and
dealt with separately.
Reviwed by: jimharris, alc
