provide no methods does not make any sense, and is not used by any
driver.
It is a pretty hard to come up with even a theoretical concept of
a device driver which would always fail open and close with ENODEV.
Change the defaults to be nullopen() and nullclose() which simply
does nothing.
Remove explicit initializations to these from the drivers which
already used them.
This will get rid of the warnings issued at shutdown (that seems to
worry alot of users), but will also no flush cache on lots of
devices that can, but doesn't set the right support bits...
Restructure the way ATA/ATAPI commands are processed, use a common
ata_request structure for both. This centralises the way requests
are handled so locking is much easier to handle.
The driver is now layered much more cleanly to seperate the lowlevel
HW access so it can be tailored to specific controllers without touching
the upper layers. This is needed to support some of the newer
semi-intelligent ATA controllers showing up.
The top level drivers (disk, ATAPI devices) are more or less still
the same with just corrections to use the new interface.
Pull ATA out from under Gaint now that locking can be done in a sane way.
Add support for a the National Geode SC1100. Thanks to Soekris engineering
for sponsoring a Soekris 4801 to make this support.
Fixed alot of small bugs in the chipset code for various chips now
we are around in that corner anyways.
Note: this might print failure messages on some systems, unfortunatly
the info from the device, stating if flushing is supported, cannot be trusted
so the operation is always issued on all devices, just in case...
Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
Clean up the DMA interface too much unneeded stuff crept in with
the busdma code back when.
Modify the ATA_IN* / ATA_OUT* macros so that resource and offset
are gotten from a table. That allows for new chipsets that doesn't
nessesarily have things ordered the good old way. This also removes
the need for the wierd PC98 resource functions.
Tested on: i386, PC98, Alpha, Sparc64
- Use it in atacontrol(8) when listing ATA devices instead of
stopping at the first ENXIO received.
This makes atacontrol list work on my sparc64 where the two ATA
channels I have are numbered 2 and 3.
Reviewed by: sos
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
This moves all chipset specific code to a new file 'ata-chipset.c'.
Extensive use of tables and pointers to avoid having the same switch
on chipset type in several places, and to allow substituting various
functions for different HW arch needs.
Added PIO mode setup and all DMA modes.
Support for all known SiS chipsets. Thanks to Christoph Kukulies for
sponsoring a nice ASUS P4S8X SiS648 based board for this work!
Tested on: i386, PC98, alpha and sparc64
To fix scsi, don't wait for ithreads if we're dumping, it makes the
debugger sad.
To fix ata, use what appears to be a polling method if we're dumping,
I stole this from tmm but added code to ensure that this change is
only in effect while dumping.
Tested by: des
Properly handle the newer Promise SuperSwap 1000 enclosures.
Print out what kind of enclosure was found in the probe.
Misc cleanups in the enclosure handling code.
Sponsored by: Advanis Inc.
This mostly consists of functionality to serialize accesses to
the two ATA channels (which can also be used to "fix" certain
PCI based controllers).
Add support for Acard controllers.
Enable the ATA driver in PC98 GENERIC, and add device hints.
Update man page with latest support.
The PC98 core team has kindly provided me with a PC98
machine that made this all possible, thanks to all that
contributed to that effort, without that this would
probably newer have been possible..
Approved by: re@
the device is not actually present), clear the corresponding bit in
the ch->devices bitmap. This resolves a panic that occurred with ATAPI/CAM
after an APM suspend/resume, when the ATA hardware would erroneously
report an extra ATAPI device.
Approved by: re, sos
Reviewed by: roberto
MFC after: 7 days
and XPT_RESET_DEV.
In order to properly handle reset requests whether they originate in the
ATA layer (atacontrol reinit) or from the CAM layer (camcontrol reset)
ata_reinit does not cause the SIM to be deallocated anymore. The SIM
is now unconditionnally created for each ATAPI bus.
This change may cause existing bus ids to change on some setups.
Reviewed by: roberto
Approved by: sos
The CAM<>ATAPI layer was submitted by "Thomas Quinot <thomas@cuivre.fr.eu.org>"
changes form the version on the net by me (formatting, ability to be used
alone without the ATAPI native device driver, proper speed reporting...)
See /sys/conf/NOTES for usage.
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
