fixes and beacon programming / debugging into the ath(4) driver.
The basic power save tracking:
* Add some new code to track the current desired powersave state; and
* Add some reference count tracking so we know when the NIC is awake; then
* Add code in all the points where we're about to touch the hardware and
push it to force-wake.
Then, how things are moved into power save:
* Only move into network-sleep during a RUN->SLEEP transition;
* Force wake the hardware up everywhere that we're about to touch
the hardware.
The net80211 stack takes care of doing RUN<->SLEEP<->(other) state
transitions so we don't have to do it in the driver.
Next, when to wake things up:
* In short - everywhere we touch the hardware.
* The hardware will take care of staying awake if things are queued
in the transmit queue(s); it'll then transit down to sleep if
there's nothing left. This way we don't have to track the
software / hardware transmit queue(s) and keep the hardware
awake for those.
Then, some transmit path fixes that aren't related but useful:
* Force EAPOL frames to go out at the lowest rate. This improves
reliability during the encryption handshake after 802.11
negotiation.
Next, some reset path fixes!
* Fix the overlap between reset and transmit pause so we don't
transmit frames during a reset.
* Some noisy environments will end up taking a lot longer to reset
than normal, so extend the reset period and drop the raise the
reset interval to be more realistic and give the hardware some
time to finish calibration.
* Skip calibration during the reset path. Tsk!
Then, beacon fixes in station mode!
* Add a _lot_ more debugging in the station beacon reset path.
This is all quite fluid right now.
* Modify the STA beacon programming code to try and take
the TU gap between desired TSF and the target TU into
account. (Lifted from QCA.)
Tested:
* AR5210
* AR5211
* AR5212
* AR5413
* AR5416
* AR9280
* AR9285
TODO:
* More AP, IBSS, mesh, TDMA testing
* Thorough AR9380 and later testing!
* AR9160 and AR9287 testing
Obtained from: QCA
The Linux ath9k btcoex code is based off of this code.
Note this doesn't actually implement functional btcoex; there's some
driver glue and a whole lot of verification that is required.
On the other hand, I do have the AR9285+BT and AR9287+BT NICs which
this code supports..
Obtained from: Qualcomm Atheros, Linux ath9k
doing split software/hardware LED configuration, we can now simply
treat "softled" as an "output" mux type.
This works fine on this DWA-552. Previous generation (pre-11n NICs) don't
have a GPIO mux - only input/output configuration - so they ignore this
field.
The hardware (MAC) LED blinking involves a few things:
* Selecting which GPIO pins map to the MAC "power" and "network" lines;
* Configuring the MAC LED state (associated, scanning, idle);
* Configuring the MAC LED blinking type and speed.
The AR5416 HAL configures the normal blinking setup - ie, blink rate based
on TX/RX throughput. The default AR5212 HAL doesn't program in any
specific blinking type, but the default of 0 is the same.
This code introduces a few things:
* The hardware led override is configured via sysctl 'hardled';
* The MAC network and power LED GPIO lines can be set, or left at -1
if needed. This is intended to allow only one of the hardware MUX
entries to be configured (eg for PCIe cards which only have one LED
exposed.)
TODO:
* For AR2417, the software LED blinking involves software blinking the
Network LED. For the AR5416 and later, this can just be configured
as a GPIO output line. I'll chase that up with a subsequent commit.
* Add another software LED blink for "Link", separate from "activity",
which blinks based on the association state. This would make my
D-Link DWA-552 have consistent and useful LED behaviour (as they're
marked "Link" and "Activity."
* Don't expose the hardware LED override unless it's an AR5416 or later,
as the previous generation hardware doesn't have this multiplexing
setup.
