both should work in non-pnp mode, the 924 should also work in its rather
braindead pnp mode- it will adopt port 0x530 unless given hints due to it
starting up in soundblaster mode and thus not requesting a valid mss port
address.
Submitted by: George Reid <greid@ukug.uk.freebsd.org>
When we get an Open event in stopped state, experience shows that this
is usually means we've somehow missed a previous Down event. This has
occasionally bitten people for the IPCP layer with ISDN, apparently a
previously aborted IPCP negotiation must have caused this. As a
bandaid, we quickly pretent a Down event by advancing to starting
state; this effectively implements the `restart' option mentioned in
RFC 1663.
While i'm not yet fully convinced this is the best thing to do (and is
fully compliant with RFC 1661), i've seen a number of reports here on
the German mailing lists where people have been bitten by the previous
behaviour which usually causes quickly looping ISDN reconnects (thus
loss of money...), and where just this patch fixes the problem.
For this, i'd even like to see it MFC'd if possible.
Submitted by: Helmut Kreft <kreft@zeus.ai-lab.fh-furtwangen.de>
1 Make promiscuous mode work
2 A few header additions
3 Allow device config before IFF_UP
These were (respectively)...
Submitted by: Allan Saddi <asaddi@philosophysw.com>
Submitted by: Dave Cornejo <dave@dogwood.com>
Submitted by: Doug Ambrisko <ambrisko@ambrisko.com>
Tested by: David Wolfskill <dhw@whistle.com>
acl_add_perm, acl_clear_perms, acl_copy_entry, acl_create_entry,
acl_delete_perm, acl_get_permset, acl_get_qualifier, acl_get_tag_type,
acl_set_permset, acl_set_qualifier, acl_set_tag_type
This brings us within 4 functions of a full ACL editing library.
Reviewed by: rwatson
pccard in the kernel for those drivers with pccard attachments. This
makes the compat layer a little larger by introducing some inlines,
but should almost make it possible to have independent attachments.
The pccard_match function are the only one left, which I will take
care of shortly.
Make struct cmessage visible from socket.h (about 4 places were
defining it for themselves which wasn't good)
Make __rpc_get_local_uid() useable and give it prototype that's
visible.
Fix some issues with printing out usernames from rpcbind and keyserv.
which resulted in the output of warning messages at boot if
UFS_EXTATTR_AUTOSTART was enabled but ".attribute" and possible
sub-directories weren't in a mounted MFS or UFS file systems.
Pointed out by: dcs
Obtained from: TrustedBSD Project
fatal trap. Also, reload the GDT register to point to BTX's GDT before
playing around with the segment registers to return to real mode. This is
helpful if the kernel causes a fatal exception before it has setup its own
IDT and fault handlers. For example, if one happens to break mtx_init().
Without these changes BTX would recursively page fault (if paging was not
disabled) or triple fault and reset the CPU (without the GDT reload)
instead of providing a potentially useful register dump.
Reviewed by: rnordier
sysctl, net.inet.ip.fw.permanent_rules.
This allows you to install rules that are persistent across flushes,
which is very useful if you want a default set of rules that
maintains your access to remote machines while you're reconfiguring
the other rules.
Reviewed by: Mark Murray <markm@FreeBSD.org>
(as is done in unmount).
Remove a snapshot inode from the superblock list when its last
name goes away rather than when its last reference goes away.
That way it will be properly reclaimed by fsck after a crash
rather than reenabled when the filesystem is mounted.
I was hanging after sending a xfer CTIO and a status CTIO for a non-discon
INQUIRY- the xfer CTIO was returned as completed OK, but the status CTIO
was dropped on the floor. All the fields looked good. I don't know why
it got dropped. But allowing status to go back with data xfer seemed to
work. I also noticed that with a non-disconnecting command that the
firmware handle in the ATIO is zero- this leads me to believe that the
f/w really can only handle one CTIO at a time in the discon case, and
it had no idea what to do with the second (status) CTIO.
CAM_SEND_STATUS. Set a timeout of 2 seconds per CTIO. Make sure
that the 'real' tag value is being checked against- not the
one that also carries the firmware handle.
