BREAK/parity/framing errors.
Term "correctly" assumes POSIX spec. and 4.4 ttyinput() behaviour.
1) Discard BREAK/parity at interrupt level when apropriate IGN*
is set in iflag. It helps "raw" mode works even IGN* is set.
2) Zero parity (if INPCK) and framing directly in buffer
before passing it to b_to_q() in "raw" mode.
Efficency:
interrupt level: if no error occurse, only two "test" commands added
"raw" mode: buf scan incc times for parity/framing added
Reviewed by:
Submitted by:
Obtained from:
CVS:
Report floppy/tape units on seperate lines as fdX:/ftX: to correct lots of
ways the current scheme failed to end the output with \n.
Add controller and/or drive designator to the fron of several messages
that come from this drive. [It's not fun to track down driver messages
using grep over the source tree.]
Reviewed by: joerg
include <pci/pcivar.h> without including <sys/devconf.h> and other
drivers include <pci/pcivar.h> before including <sys/devconf.h> if
certain identifiers are defined.
The devconf headers have convoluted interdependencies. <sys/devconf.h>
includes <machine/devconf.h> which includes <pci/pcivar.h>. Most
drivers include <sys/devconf.h> so even isa drivers depend on
<pci/pcivar.h>. For similar reasons, most drivers depend on another
pci header, on an isa header and on two scsi headers.
NOT derived from the Linux code and is thus not GPL'd. It is the author's
express wish that the GPL copyrighted version be removed and this BSD copyright
version take its place. Considering our own stance on this, I'm certainly
not going to argue! [Note to NetBSD folks: You're free to grab it now :-)]
Submitted by: Mikael Hybsch <micke@dynas.se>
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
1) Supports PCI to PCI bridge devices (and tries to initialise them,
even if the BIOS is brain dead).
2) Supports shared PCI interrupts. Interrupt handlers now MUST return
'0' if they found nothing to do, '1' otherwise.
New features tested with i486 systems based on the Intel Saturn and
a DEC 4channel Ethernet card only, but expected to work on most systems.
The option PCI_REMAP has been removed !
Submitted by: Wolfgang Stanglmeier <wolf@kintaro.cologne.de>
a device specific shutdown routine for devconf. Assign the value of this
to the kern_devconf struct. Implement a device shutdown routine for if_de
that disables the device. This will stop the device from corrupting memory
after a reboot.
Let "grey delete" be a function key (default is 0x7f)
Fix the xor cursor again..
Made the backspace key generate del as default
Made CTRL-space generate nul as default.
(a) bring back ttselect, now that we have xxxdevtotty() it isn't dangerous.
(b) remove all of the wrappers that have been replaced by ttselect
(c) fix formatting in syscons.c and definition in syscons.h
(d) add cxdevtotty
NOT DONE:
(e) make pcvt work... it was already broken...when someone fixes pcvt to
link properly, just rename get_pccons to xxxdevtotty and we're done
DEC 21050 chip in particular, don't have specs of other such chips).
This should add support for Multiple-Ethernet PCI cards (e.g. Znyx 314).
Reviewed by: se
Submitted by: <wolf@kintaro.cologne.de> Wolfgang Stanglmeier
is close to 1000000 / 960 usec so the confusion probably didn't matter.
Test for COMCONSOLE before testing for RB_SERIAL so that the RB_SERIAL
test can be optimized away if COMCONSOLE is 1.
Simplify and Uniformize style of previous commit.
(b) add a function callback vector to tty drivers that will return a pointer
to a valid tty structure based upon a dev_t
(c) make syscons structures the same size whether or not APM is enabled so
utilities don't crash if NAPM changes (and make the damn kernel compile!)
(d) rewrite /dev/snp ioctl interface so that it is device driver and i386
independant
labels.
Please test the slice/label features:
cd /dev; sh MAKEDEV svn0
cd /var/tmp; dd if=/dev/zero of=vnfile bs=8192 count=1024
vnconfig -c /dev/rvn0 /var/tmp/vnfile
fdisk /dev/rvn0 # invent a geometry, create one BSD partition
disklabel -r -w vn0 floppy # a convenient (bogus) label
disklabel -e vn0 # edit label to match device
newfs /dev/rvn0a
mount /dev/vn0a /mnt
...
The steps after the fdisk could name the device vn0s1 instead of vn0.
PCI BIOS mappings are retained, except if option PCI_REMAP
is specified in the kernel config file.
There is now a list of attach addresses, and the first
address that seems to make some device registers appear
is chosen.
Reviewed by: se
Submitted by: wolf
Removed screensavers from syscons, they are now LKM's. This makes it
possible to do some really "interesting" screensavers...
Fixed bug that sometimes caused garbage to appear when leaving
"scroll-lock" history.
Reformattet indentation, it got too deep for a normal 80 pos screen.
Split up in syscons.c & syscons.h for use with the saver-lkm's.
Temporarily removed -s option from vidcontrol, savers should now
be loaded with modload.
briefly over it, and see some serious architectural issues in this stuff.
On the other hand, I doubt that we will have any solution to these issues
before 2.1, so we might as well leave this in.
Most of the stuff is bracketed by #ifdef's so it shouldn't matter too much
in the normal case.
Reviewed by: phk
Submitted by: HOSOKAWA, Tatsumi <hosokawa@mt.cs.keio.ac.jp>
when ttselect() is improved. This requires using an array of tty structs
and not using ttymalloc().
Fix an off by 1 error. Some caclulations seem to be off by a factor
of NCY. NCY defaults to 16, which gives 256 tty structs occupying
0xd000 bytes. The minor number encoding only allows 16 ttys.
Update the types of timeout functions to 2.0.
- Overflow now calculated right
- Close works ok,does not looses tty
- Better overflow handling now the snooping stops
on overflow,but programm notified and can reconnect if
it want to..Default maximal buffer set to 664 K and this
is probably too much..:)))
Utility still to come
New config option "NCR_IOMAPPED" makes the driver use port I/O.
Put back in 53c815 defines, submitted by Mikael Hybsch <micke@dynas.se>.
These had got lost between cvs rev. 1.14 and now ...
pci.c:
Really write config space register.
Assign ports starting at 0xbc00.
Submitted by: wolf
Reviewed by: se
Users-beware..
It is tested and working for me but probably have some bugs i
didn't noticed so test it and reply...
It can:
look at what's sent to the user from tty device
snoop on pty's,vty's and serial tty's
It (still) can't:
write to tty
see what user types in local echo mode
It is probably bad styled and
very dependant on tty_pty.c,sio.c and syscons.c
I would be really happy if another ppl would make their
changes because i am not sure this is the best snoop
we can have..but it is good..:)))))
so that the interface won't have the effect of blocking other senders
during bulk transfers (i.e. hogging the ethernet). It improves performance
in all of my tests by reducing collisions and I believe it to be a Good
Thing.
adapted to FreeBSD by Heikki Suonsivu <hsu@cs.hut.fi>.
Submitted by: Andrew Werple <andrew@werple.apana.org.au> and
Heikki Suonsivu <hsu@cs.hut.fi>
Obtained from: NetBSD
definitions taken from the PCI specs. Part of them were typed
in by Wolfgang Stanglmeier, the (at that time unneeded) rest
by Charles Hannum (thanks !).
Display update method changed, now allways write in memory buffer,
then periodically update physical display.
Speed improvements (now > 5 times faster than the old syscons).
History now circular buffer, with changeable size.
History scroll by up/down line, up/down page, home and end.
Backtab proberly implemented.
Now space for 96 function keys, 63 allocated standard, default now
SCO/SYSV compat again as in the old days.
New keyboard definition files ~share/syscons/keymaps/*
Misc fixes for old "hacks" that broke SCO/SYSV compat.
More that I forgot before writing this...
case, software cursor now optional case. Driver must provide
raw things (what hardware do for us, exactly) as default case,
all driver features must be _optional_. Modern VGAs have internal
configuration utilities to set cursor shape/blinking which stored
into cards ROM, and syscons nuke out such features completely
by forcing software cursor. Moreover, software cursor is hard
to distinguish on standouted (or near standouted) fields and
tends to disappearse from the screen.
Set "flags 0x4" to enable software cursor now.
o Cleanup screen savers.
o Don't draw cursor if saver or blinker is active.
o Duplicated code moved to functons.
o Add more checks for blinker in progress, character lost otherwise
when blinker restore old contents.
o Reduce blinking counter to 3, too slow in old variant.
o Fix timeout code in scrn_timer(), old variant can reenter iself,
if action takes too long time.
o Disable visual bell for scroll lock mode, saved screen
becomes overwritted otherwise.
in the PCnet/Lance family.
Fix attach so 32 bit cards don't call isa_dmacascade.
Add a workaround for 32 bit chips which incorrectly truncate the
ring buffer size.
Fix a bug where CRC errors were reported as framming errors.
Change copyright to a BSD style one.
Print out the length of the compiled sequencer program.
aic7xxx.seq:
More optimizations. Replace generic bcopy routine with bcopy_3
and bcopy_4 (ie unroll the loops) since these are the only two cases used.
Initialize SIMODE1 and SXFRCTL1 from the kernel in ahc_init instead of
at each selection/reselection since this is expensive and only needs to
be done once. Condense function returns into previous instruction if possible.
Reorder some sections to kill superflous jumps. These optimizations kill
the ~150k/s penalty adding support for Twin/Wide cards was costing since
the last place in the commaon path of execution where we had to do ugly,
convoluted testing for the type of card in the sequencer has gone away.
Next stop tagged queuing and target mode.
Obtained from:
sio.c and sioreg.c changed to allow autodetecting the RB_SERIAL flag
passed by the boot blocks so that the kernel can switch to 'serial
console' mode automagically. 'options COMCONSOLE' can still be specified
to force the kernel to always use the serial port as a console.
CONUNIT and CONADDR can also be specified in the kernel config file
if the user wants to shift the console to a different port.
(SCSI control block) instead of having the host PIO it down. Also
reimplement WDTR and SDTR optimization to remove code in the sequencer
and place the responsibility of knowing when to initiate SDTR or WDTR
on the kernel driver. This vastly shortens the sequencer program yet
yeilds the same performance.
properly from the beginning:
1) The `kern_devconf' struct should be a part of the driver's
`softc' structure (now it is).
2) The `description' should say what the device actually is,
rather than just giving a model number (now it does).
3) The device should be registered even if the probe fails, so
that it can be reconfigured later.
4) For netifs, the device state should follow the IFF_UP flag.
Other network interfaces should follow this example. (Please?) Eventually
there should be a rundown routine doing the equivalent of setting IFF_UP
off, and perhaps more if warranted.
sense retrieval code that messed up CDROM devices. This code will also
responde correctly to SDTR and WDTR messages from devices that start a
negotiation sequence.
protected drive at open() time has been *totally bogus*! The guy who
submitted it didn't understand all the implications of calling
set_motor(), and the `who' who included the patch into the tree did it
blindly... Pleeeeze, don't commit code to this driver unless you are
really going to understand what it does! This one caused me to pull
out even more hears, and those who know me do know that i ain't got
too many o'them. :-)
No kernel config options anymore besides keyboard language layout.
Virtual consoles are now dynamically allocated, no NCONS anymore.
Software cursor blinking/nonblinking.
Visual bell for laptops (don't beep at meetings :-).
Cursor/bell default type setable via config "flags" instead of as defines.
Cursor/bell type setable via ioctl's.
New video modes 80x30 80x60 for some laptops, and those with multisync monitors.
Scroll-lock history (length currently fixed at 100 lines).
Lots of cleanups, some only commented out for now (will goaway soon).
Support for new features in vidcontrol/kbdcontrol.
Updated manpages.
now marked busy as long as it's being in non-reset state, and the
drives are busy as long as at least one instance is open.
Also reformat everything to fit into 80 columns again.
Changed my mind wrt. error reporting for a write-protected drive and
an open() with write intent; ENXIO has been too weird, now return EIO.
Some portions of the code need to be rewritten to use tprintf()
instead of simple printf()'s, so the messages will also appear on the
session terminal, however.
floppy driver (or in the hardware?). It turned out to be caused by
spurious interrupts, right after an FDC reset.
Also major cleanup in the low-level structure, there are now functions
performing error-checks for the FDC I/O.
Submitted by: (mostly) Peter Dufault <dufault@FreeBSD.org>
correct console number for the VT_WAITACTIVE ioctl. Invalid console numbers
caused waiting on an invalid pointer.
Use bcopyw() instead of move_up() and move_down(). bcopyw() handles
overlapped copies and should be faster. Actually use bcopy(). bcopy()
is slightly faster if video memory is 16-bit and about twice as fast if
it is 32-bit. bcopy() is said to fail on someGA's, but syscons already
depends on it working for other accesses to video memory.
You can now sling 14 devices off of a 274xT. In the process of adding
twin channel support, I removed all evident restrictions on supporting
Wide channeled devices, but I do not have a Wide controller to test them
on.
aic7770_seq.h, the pre-compiled header, is no longer needed since config
handles this dependancy.
- /sys/i386/isa/if_ed.c doesn't quite know how to deal with SMC EtherEZ
ethernet cards. The EtherEZ looks just like the Elite Ultra, except it
has only 8K of shared memory. The only way to have it properly detected
is to zero and test a few bytes of memory just about the first 8K region.
If it clears properly, it's an Elite Ultra, otherwise it's an EtherEZ.
I've also got an EtherEZ patch for netboot (Makefile, ether.c and ether.h).
- /sys/i386/isa/syscons.c wraps at the next to the last column rather than
the last column, like it should. You don't really notice this unless you
use certain programs that write all the way out to, say, the 80th column,
like VMSmail. Along with a one-line fix for this are some changes to
implement a non-blinking cursor. Put 'options "NOBLINK_CURSOR"' in your
config file and give it a try. :)
Submitted by: wpaul
is supposed to work except "media removal" (shutting down the vn driver)
while some partitions are open.
Fix some errnos: return ENOTTY, not ENXIO for unknown ioctls; return
ENODEV, not ENXIO for the unsupported dump operation.
worked in the past only because of good fortune. Anyway, use the contig alloc
routine I wrote awhile ago (vm_page_alloc_contig) for the sound code to do
this allocation. Also, specify read+write on the permissions to pmap_enter().
Specifying just read can have unexpected consquences.
Now floppy tape support is *disabled* unless you specifically
request otherwise. Poul wanted it this way, and I guess I'm not going to argue
though it may seem counter-intuitive. We can always change it back, later.
make the sequencer code fully compatible with the aic7870 (ie 294x adaptors).
I've also added to my local mods putting the sequencer into "FASTMODE" clock.
This gives upwards of 2M/sec write preformance improvement in some scenarios.
There haven't been any reports of this causing problems, and I have been
reaping the benifits of it for more than a week now.
This also includes a new version of the pre-generated file <ugh>
Obtained from: John Aycock (aycock@cpsc.ucalgary.ca) and myself
flags & 0x1. Somebody should build a kernel with this and see if
the floppy-tape damaged people can turn it off properly with userconfig.
I can't reproduce the original problem here.
and into ether_input(). It was silly to have bpf want this one way and
ether_input want it another way. Ripped out trailer support from the few
remaining drivers that still had it.
1) make #includes correct
2) fix bugs in address check macros
3) fixed bugs in, and enabled, recopy if heavily fragmented code
4) moved call to bpf tap to be before enqueing packet (probably gratuitous)
5) fixed bug that caused "abnormal interrupt" at boot time/first use
6) added support for reading Zynx address ROM
7) fixed bug that caused broadcasts to not work shortly after booting (only
manifested if not using multicast - e.g. not in FreeBSD 2.0)
8) fixed spelling errors in comments
Submitted by: Matt Thomas
a discussion going on about removing this code from the burden of the
GPL, but it won't happen before Beta, and this code should be tested
before release.
Supports 27/2842 class adaptec cards and is almost capable of supporting
aic7870 based adapters (294X series cards). It does not support Wide
controllers or the second channel on Twin boards although I have work in
progress on getting both channels and running.
I have also added a few performance improvements to this version that give
us approximately a 25% boost over the original driver. These patches have
been submitted to the author.
Obtained from: Linux aic7770 driver (John Aycock - aycock@cpsc.ucalgary.ca)
of the 1.1.5 driver, a recent version of the NetBSD driver, Andres'
transmission start threshold code, and all other relavent changes to the driver
since it was brought into 2.0. The multicast support from NetBSD has not be
folded in yet. I've tested it under high loads for two weeks and it is now
robust enough to be included in the GENERIC kernel.
Reviewed by: gibbs
Submitted by: vega@sophia.inria.fr (Andres Vega Garcia)
cosmetique) because we already have right things there or his changes
are incorrect.
Fix mcd_subchan to return position, inspired by idea from
bugress@s069.infonet.net, but different implementation.
Here is the improved probe for the mse (Bus Mouse) device driver. I
have been running with this under 1.1.5.1 as well as 2.0 without a hitch for
quite a while.
Submitted by: lars
floppies now. I'm not sure why, but things hang when it gets to the
`changing root to fd0c' part. Without your latest commit, everything works
fine. Maybe you can figure out what you broke after ALPHA! :)
errors at a lower ipl. clist starvation problems can cause hundreds of
tty buffer overflows per second and logging them all amplified the
problems. This problem was less serious in 1.1.5.
Avoid a race in the check for starting a new block of output. com_events
was sometimes messed up and siopoll() looped endlessly. This bug was
introduced in 2.0.
Clean up previous 2 commits. Rename sio_registerdev() to sioregisterdev()
to match the (bad) surrounding naming conventions. There should be a
generic_registerdev().
. avoid resetting the FDC every time the last motor is going off;
instead, give it a 60-second period for possible later reactivation.
This prevents us from needing to recalibrate the FDC too often,
but still allows for an ``automagic error recovery', just in case the
controller is absolutely stuck. (Simply wait for 60 seconds, and
try it again.)
. made the floppy head settle time after a seek a constant
that might be overridden by a config option. (Well, actually the
divisor of the settle time). Pepople often reported problems with
their floppies, so i need a simply mechanism that allows them
to play with that value. (I personally cannot find any problem
on *my* drives.)
. implement the FD_DEBUG ioctl command, in case the driver
is compiled with DEBUG turned on.
. removed a bogus parameter from a printf; the remaining warnings
from gcc -Wall seem to be warnings about the %b format gcc cannot
understand
. rearrange Garett's code to fit better in the existing structure
of #define/type/function ordering.
. make everything fit into 79 columns again.
in the far pointers are multiples of 4K (as is normal when the video
BIOS is at seg 0xc000). Disallow mode switching if the pointer is bad.
Use a new pa_to_va() macro for all BIOS and video addresses in syscons.
and all SCSI devices (except that it's not done quite the way I want). New
information added includes:
- A text description of the device
- A ``state''---unknown, unconfigured, idle, or busy
- A generic parent device (with support in the m.i. code)
- An interrupt mask type field (which will hopefully go away) so that
. ``doconfig'' can be written
This requires a new version of the `lsdev' program as well (next commit).
so i hope i've finally removed all the occasions where the driver
got stuck when there's no floppy in the drive.
Also attemmpting to omit the error mesage for ``recalib failed''
for the first time, since people tend to be confused about this.
else has been probed. This feature could go away again, if we can curb the
problem another way.
if_ed.c, syscons.c: Set the above flag. ed# because it needs it, syscons
because it looks stupid to "detect" the display you have already filled up
with text :-)
bt742a.c: Check bt_cmd() return-val during probe, thus failing on adaptec's.
Also silenced various printf's during the probe.
isa.c: Probe devices with the above flag set before the rest. Reduce the
number of "conflict" messages per device to one.
***
Please test the GENERIC-kernel now, if nobody can make it fail, GENERICAH
and GENERICBT has a finite and short life-expectancy...
***
of mb_offset given the right sequence of 1 and 0 byte mbufs. This bug
was discovered by John Hood who also provided this fix - which is a
rewrite of the routine (and is easier to understand than the code I wrote).
Submitted by: John Hood <cgull@smoke.marlboro.vt.us>
Fix endless loop in siopoll() for an event on a tty with no tty struct.
Don't generate unwanted interrupts in the serial console driver. These
bugs probably don't matter unless the tty struct is dynamically allocated.
Support polled mode. To use it, leave out the irq and the vector in
the config file. It only causes extra overhead for open polled ports.
The maximum usable speed is approximately 1000 bps for a 16450 and
15000 bps for a 16550.
Other cosmetic changes.
Bug fixed, that caused system hang on first interrupt on some motherboards.
New version of PCI bus configuration code, now supports dynamic interrupt
configuration (using BIOS supplied values).
NCR SCSI and DEC Ethernet driver patched to use this feature.
*** Remove PCI IRQ specifications from your kernel config file ! ***
the first place was so that BPF could grok trailer packets. I've since
decided that this is a job for tcpdump to decipher (if at all). Also
fixed up checks for received packet length to better cope with ancient
starlan boards.
be merged at some point)
New AMD family ethernet driver. Should support BICC,NE2100, TNIC,
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
New version with improved support for WIDE SCSI using the NCR 53c825.
Test for buggy secondary cache implementations.
PCI Int to IRQ mapping now specified per slot.
This is needed for having the fdformat program no longer searching
non-public include paths.
Protect the definitions in fdreg.h against double inclusion.
more work required to grab all fonts
2)Make standard VGA font as default, make HARDFONTS an option
(load iso8859 fonts instead)
3)Check fonts_loaded for all restore (copy_font...palette)
sequences.
when the drive had been left on a cylinder > 67 after kernel boot. The
most common case for this is booting a kernel that is located on
the inner cylinders of a floppy.
Also removed all occurences of spinwait(), replaced by DELAY.
Nuked a return line saying nothing, this might make Bruce happy 8^)
Submitted by: partially by Bruce Evans
date: 1994/05/22 12:35:38; author: joerg; state: Exp; lines: +6 -6
First round of floppy changes. Try making `fd' more robust.
New features:
. ioctl command for setting the drive type (density etc.); restricted
to the super-user
. ioctl for getting/seting `drive options'; currently only option
is FDOPT_NORETRY: inhibit the usual retries; used when verifying
a newly formatted track
Fixes:
. function prototypes
. made all internal functions `static'
. cleaned up & corrected .h files
. restructured, to make the chaotic function sequence more rational
. compiled with -Wall, and cleared all warnings
. introduced a mirror for the (write-only) `digital output register',
to avoid the current kludge
. device probing completed by seeking/recalibrating, and looking
for track 0 being found
. holding the controller down in reset state while it is idle (and
thus saving allot of headaches)
. make requests fail that are not a multiple of the (physical)
sector size
. removed the fixed physical sector size (512 bytes), allowing for any
size the controller could handle (128/256/512/1024 bytes)
. replaced some silly messages
. fixed the TRACE* macro usage, debugging reports should be complete
now again (debugging output is HUGE! though)
. removed fd_timeout for SEEK command; seeks are always reported by
the controller to succeed, since the `success' only refers to the
controller's idea of success - there is no hardware line to tell about
the seek end (other than the `track 0' line)
. catch SENSEI's that report about a `terminated due to READY changed'
status - could happen after a controller reset
. converted ``hz / <something>'' divide operations to divisors that are
powers of two, so gcc can optimize them into shifts
. write/format operations are checked against a write-protected medium
now *prior* starting the operation
. error reports of `invalid command' and `wrong cylinder' will cause
shortcuts in the retrier() now
. fixed a bug in the retrier() causing bogus block numbers to be reported
. fdformat() does care for errors now
Known Bugs:
. no attempts have been made (yet) to improve the performance
. sometimes, bogus ``seek/recalib failed'' messages are logged; this
is still a bug in the driver, but it's not harmful since it's
usually caught by the retrier()
Reviewed by:
Submitted by:
Obtained from:
320x200 256col VGA. This is nessesary for the iBCS stuff to work right.
(And we get the benefit of more video modes). Uses the videocard BIOS
to optain mode tables.
Added a "green" saver, switches off the syncs for "green" monitors.
Reviewed by:
Submitted by:
Obtained from:
wider variety of systems. Include the deivers from pci_intel.c in
pci_config.c (I hope this is what was intended; my system works ok).
Use pmap_mapdev(). Automatically map any large linear frame buffers
or whatnot in VGA-style devices which ordinarily would not have their
own drivers, and don't call not_supported() for them. (This shuts up
complaints about my Matrox card.) Include the beginnings of what could
eventually become dynamically-loadable PCI devices. Allow for the
possibility of PCI devices simply providing a PCI veneer over an existing
ISA device, and shut up about them, too.
Make autoconfiguration text conform more to the style of other supported
buses.
you download the microcode to the DSP everytime you power on your system.
They provide a dos-program to do so, but no other support. This commit adds
code to the sio-driver, which implement an ioctl, which will down-load the
micro-code.
To get this functionality, you must define DSI_SOFT_MODEM.
The program to actually employ the ioctl is not included, but the entire
source looks like this:
#include <sys/ioctl.h>
#include <stdio.h>
main()
{
unsigned char buffer[100000];
int i;
read(0,buffer,100000);
if((i = ioctl(1,TIOCDSIMICROCODE,buffer)) < 0)
perror("ioctl");
return i;
}
And you use it like this:
smload < data144b.dsi > /dev/ttyid3
You need to copy the *.DSI files from the dos-media provide with your modem.
You can see what is downloaded by issuing the ATI3 command to the modem.
DSI's scheme for what code you can run on your modem isn't violated by this.
Poul-Henning Kamp
phk@freefall.cdrom.com
Add initialization to the if_ie driver for the Micom Interlan NI5210 card.
This is a very old 82586 based card with only 8Kb or 16Kb on board memory.
Also only 8-bit wide instead of 16-bit like the AT& or 3COM card.
Warning: this thing is only tested so far that it detects all bits
correctly but is not yet on an ethernet. Will do that tomorrow.
Submitted by:
Update the if_ep driver for the 3C579 and bring over some of the
changes from the netbsd driver.
This is not complete: the detection of the irq in the eisa does not
work and sometimes the reset for the 3C509 in ISA in an EISA bus system
don't work ( Need a hard reset to be found again == reset knob).
DIOCGDINFO, DIOCGPART, DIOCWDINFO, DIOCSDINFO, CDIOCPLAYMSF, CDIOCRESET,
CDIOCEJECT.
CDIOCPLAYBLOCKS removed (old implementation completely wrong and I don't
know how to implement it correctly).
All routines now detects media change correctly.
DELAY_GETREPLAY increased for long time access from first track
to last.
mcd_waitrdy() now use MIN_DELAY=15 as minimal delay which independs
of machine speed.
mcd_doread() now uses real status (old code uses obsoleted soft copy of it).
clear XBSY on error in mcd_doread()
mcd_statrt(): add missing splx(s), cause dead hang with unmatched slpbio()
optimize mcd_doread(), don't set CD mode each time, keep soft copy of mode.
call getdisklabel() _after_ mcdsize() for proper sizes
mcdopen(): old code forget to set MCDREADRAW in flags when open RAW
partition, doread check it for setting RAW CD mode.
Do nothing on stray interrupt (which sometimes occurse, because driver
read data block too slow, DOS driver use 'insb' here). Old stray code
cause timeouts.
Read toc entries code rewritten to return many requested entries
(as supposed) instead of one entry with incorrect structure.
CMDREAD2 requests covered with disable_intr()/enable_intr()
(from DOS driver)
Read junk code added after read block code in doread (from DOS driver)
mcd_read_toc() code fixed to read all needed entries, old code cause
some audio tracks is not played.
mcd_playtracks() code fixed to proper check valid track range.
New binary read modes implemented (from DOS driver).
Submitted by:
Put the printf("can't map 3c507 ram.. into an ifdef DEBUG. This will
confuse only normal users and the ie0 found/not found is sufficient.
Submitted by:
1) if_ie.c:
Changed a printf and put a space in it. Formerly the "<3C507>"
confused the syslog. He tried to see that as the priority to
log that message.
2) isa_device.h:
Changed the iobase variable from short to u_short. EISA
Adresses can go up to 0xf000 and the sign extension doesn't
look good in the probe output. Example:
ep1 at 0xffff8000-0xffff8000f is not good :-), i like more a
ep1 at 0x8000-0x8000f.
3) isa.c:
Changed a string constant from "probe" to "prob", it gets
later already an "ed" tagged on the end.
in your kernel config now).
2) Added ps ddb function from 1.1.5. Cleaned it up a bit and moved into its
own file.
3) Added \r handing in db_printf.
4) Added missing memory usage stats to statclock().
5) Added dummy function to pseudo_set so it will be emitted if there
are no other pseudo declarations.
2) DELAY(1) does nothing, it affects audio playing f.e:
driver can't play second half of disk, changed to DELAY(10)
3) Debugging messages #ifdef DEBUGed
find something useful to do other than taking credit for other people's
work. Also make the 3C507 bits match the indentation style of the rest of
the code.
Merged changes from 2.0 version (revisions 1.46-1.50) by hand.
Finished conversion to clists: removed flush of tty output buffer
in comflush() (most writes were truncated to 256 bytes) and restored
bypass of ttyinput() in siopoll().
Finished conversion to 2.0 types - more void *'s, less caddr_t's,
less casts, no Dev_t's.
Only these things are seriously broken now compared with 1.1.5:
waiting for output complete is impossible so ttywait() can deadlock;
sioclose() isn't called enough so sioopen() sometimes returns EBUSY
unnecessarily; input flow control is not implemented.
Submitted by:
Add the 3com 3C507 card to the if_ie.c driver. The files elink.c and
elink.h are helding routines that are shared between the 3C507 and the
3C509/3C579. if_ie507.h are constant declarations unique to the 3C507.
The code is based on the NetBSD driver if_ie.c donated to NetBSD by
Rafal Boni and then modified by Charles Hannum.
Added a missing #ifdef INET wrapper in lpt.c
Main change:
Removed the timeout_func_t casts from timeout calls and
correctly defined the timeout routines to conform to
the new format.
lpt.c doesn't have this change.
Reviewed by:
Submitted by:
