Include read streaming in the PPR flags we display in diagnostics.
In ahd_reset(), set the known mode after our initial pause prior to
setting the mode. We can't just set the mode directly because the
current mode, after the pause, is most likely unknown and setting the
mode when the saved mode is unknown will trigger an assertion in
the mode debug code.
Complete an audit for SCB RAM reads. These reads must be performed
via the special ahd_in?_scbram() methods so we can perform a
Rev A. PCI-X workaround.
Remove a superfluous mode save operation that was performed just
prior to a call to ahd_clear_critical_section(). The saved mode
was never restored and wouldn't have been valid anyway since the
mode could change while single stepping out of a critical section.
aic79xx.h:
Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG.
aic79xx_inline.h:
Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG
and only apply the workaround if this bug is active. The old code
applied the workaround in all cases.
aic79xx_pci.c:
Set AHD_PCIX_SCBRAM_RD_BUG for the A4.
Remove an attempted saved_modes call in ahd_pci_test_register_access().
Saving the modes can only occur when we are paused, but the call was
happening before the chip was known to be paused. Restoring the
modes doesn't make sense either since the code makes no assumptions
about the state of the sequencer until the first time the mode is set
by the driver. This happens after the registers are successfully
mapped.
Clear the LQICRC_NLQ status should it pop up after we have
already handled the SCSIPERR. During some streaming operations
this status can be delayed until the stream ends. Without this
change, the driver would complain about a "Missing case in
ahd_handle_scsiint".
In the LQOBUSFREE handler...
Don't return the LQOMGR back to the idle state until after
we have cleaned up ENSELO and any status related to this
selection. The last thing we need is the LQO manager starting
another select-out before we have updated the execution queue.
It is not clear whether the LQOMGR would, or would not
start a new selection early.
Make sure ENSELO is off prior to clearing SELDO by flushing
device writes.
Move assignment of the next target SCB pointer inside of
an if to make the code clearer. The effect is the same.
Dump card state in both "Unexpected PKT busfree" paths.
In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1.
That register only exists in the SCSI mode. Also set the mode
explicitly to the SCSI mode after chip reset due to paranoia.
Re-arrange code so that SXFRCTL1 is restored as quickly after the
chip reset as possible.
S/G structurs must be 8byte aligned. Make this official by saying
so in our DMA tag.
Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come
true. This can cause a CIO bus lockup if a PCI or PCI-X error
occurs while the stretch is occurring - the host cannot service
the PCI-X error since the CIO bus is locked out and SHVALID will
never resolve. The stretch was added in the Rev B to simplify the
wait for SHVALID to resolve, but the code to do this in the open
source sequencer is so simple it was never removed.
Consistently use MAX_OFFSET for the user max syncrate set from
non-volatile storage. This ensures that the offset does not
conflict with AH?_OFFSET_UNKNOWN.
Have ahd_pause_and_flushwork set the mode to ensure that it has
access to the registers it checks. Also modify the checking of
intstat so that the check against 0xFF can actually succeed if
the INT_PEND mask is something other than 0xFF. Although there
are no cardbus U320 controllers, this check may be needed to
recover from a hot-plug PCI removal that occurs without informing
the driver.
Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes
an infinite loop at card initialization if the cacheline size is 0.
aic79xx.h:
Add AHD_EARLY_REQ_BUG bug flag.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the
curr->offset can never be, unlike '0' which we previously used.
This fixes code that only checks for a non-zero offset to
determine if a sync negotiation is required since it will fire
in the unknown case even if the goal is async.
aic79xx.reg:
Add comments for LQISTAT bits indicating their names in the 7902
data book. We use slightly different and more descriptive names
in the firmware.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
aic79xx.seq:
Update comments regarding rundown of the GSFIFO to reflect reality.
Fix spelling errors.
Since we use an 8byte address and 1 byte length, shorten the size
of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes.
Remove code that, assuming the abort pending feature worked, would
set MK_MESSAGE in the SCB's control byte on completion to catch
invalid reselections. Since we don't see interrupts for completed
selections, this status update could occur prior to us noticing the
SELDO. The "select-out" queue logic will get confused by the
MK_MESSAGE bit being set as this is used to catch packatized
connections where we select-out with ATN. Since the abort pending
feature doesn't work on any released controllers yet, this code was
never executed.
Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ
assertions just because they were asserted within the bus settle delay
window. This allows us to tolerate devices like the GEM318 that
violate the SCSI spec.
Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit
should have no effect, but who knows...
On the Rev A, we must wait for HDMAENACK before loading additional
segments to avoid clobbering the address of the first segment in
the S/G FIFO. This resolves data-corruption issues with certain
IBM (now Hitachi) and Fujitsu U320 drives.
Rearrange calc_residual to avoid an extra jmp instruction.
On RevA Silicon, if the target returns us to data-out after we
have already trained for data-out, it is possible for us to
transition the free running clock to data-valid before the required
100ns P1 setup time (8 P1 assertions in fast-160 mode). This will
only happen if this L-Q is a continuation of a data transfer for
which we have already prefetched data into our FIFO (LQ/Data
followed by LQ/Data for the same write transaction). This can
cause some target implementations to miss the first few data
transfers on the bus. We detect this situation by noticing that
this is the first data transfer after an LQ (LQIWORKONLQ true),
that the data transfer is a continuation of a transfer already
setup in our FIFO (SAVEPTRS interrupt), and that the transaction
is a write (DIRECTION set in DFCNTRL). The delay is performed by
disabling SCSIEN until we see the first REQ from the target.
Only compile in snapshot savepointers handler for RevA silicon
where it is enabled.
Handle the cfg4icmd packetized interrupt. We just need to load
the address and count, start the DMA, and CLRCHN once the transfer
is complete.
Fix an oversight in the overrun handler for packetized status
operations. We need to wait for either CTXTDONE or an overrun
when checking for an overrun. The previous code did not wait
and thus could decide that no overrun had occurred even though
an overrun will occur on the next data-valid req. Add some
comment to this section for clarity.
Use LAST_SEG_DONE instead of LASTSDONE for testing transfer
completion in the packetized status case. LASTSDONE may come up
more quickly since it only records completion on the SCSI side,
but since LAST_SEG_DONE is used everywhere else (and needs to be),
this is less confusing.
Add a missing invalidation of the longjmp address in the non-pack
handler. This code needs additional review.
aic79xx_inline.h:
Fix spelling error.
aic79xx_osm.c:
Set the cdb length for CDBs dma'ed from host memory.
Add a comment indicating that, should CAM start supporting cdbs
larger than 16bytes, the driver could store the CDB in the status
buffer.
aic79xx_pci.c:
Add a table entry for the 39320A.
Added a missing comma to an error string table.
Fix spelling errors.
Add a constant for the controller's stack size and the
maximum scsi offset.
aic7xxx.seq:
Style nit. The source is implied to be the destination
unless overridden in an "and" instruction.
Update target mode code for changes in identify seen
sequencer flags.
aic7xxx_pci.c:
Ensure that the PCIERRGENDIS bit is set in the
PCIERRGEN config space register. Perhaps this
is a reason for the spurios parity errors reported
on U160 controllers.
Honor the AHC_NO_BIOS_INIT flag.
Allow PCI interrupt reporting to be disabled,
by clearing the PERRRESEN bit in the command
register. This option is now enabled via a new
softc flag: AHC_DISABLE_PCI_PERR.
Disable SERR and pause the controller prior to performing
our mmapped I/O test. This should handle the case of
controllers that do not "auto-access pause". For legacy
controllers, use SCB ram instead of scratch ram since
the latter may contain settings left over from the BIOS
that we will use if an seeprom is not found.
Make use of new ahc_inl/outl() inlines.
aic7xxx.h:
Reformat a few comments to follow driver style.
Add a controller flags that indicate that a controller
has not been initialized by the BIOS and whether to
disable PCI parity errors..
Remove stack probing softc members.
Add a few more syncrate constants that are useful in speed
fallback calculations.
Add the SHOW_MASKED_ERRORS debug flag.
aic7xxx.h:
aic7xxx.c:
Implement the SCB_SILENT flag. This is useful for
hushing up the driver during DV or other operations
that we expect to cause transmission errors. The
messages will still print if the SHOW_MASKED_ERRORS
debug option is enabled.
aic7xxx_inline.h:
Implement ahc_[in|out][w|l|q]. This removes the need
for manual 'or and shift" type operations throughout
the driver.
aic7xxx.c:
Move SELTO dignostic so that the SCB is still valid
when we use it for printing path information.
If we are narrow, limit syncrate to Ultra2.
Don't clobber ppr_options when forcing a renegotiation.
The current ppr_options may be referenced while queuing
new commands. Don't set our width to unknown when forcing
negotiation on narrow controllers. This will confuse the
negotiation code into negotiating with a wide message on
narrow controllers.
Add an "asserting atn" diagnostic with controller/target
information.
Remove the probe_stack code. The stack is always
4 deep on legacy controllers, so probing is pointless.
This also avoids an issue where probing the stack would
upset the aic7770.
In ahc_reset(), record whether or not we found the
controller in a reset state. If the controller was
already reset, assume that no BIOS has initialized
the controller and ignore left over scratch ram
settings.
Fix an ifdef bug that caused sequencer debugging to
be enabled always.
Clear the ultraenb flag in our tstate during startup.
The ultraenbled'ness of a device is recorded in the user
transfer settings. tstate->ultraenb bitmask indicates
which devices we have negotiated an ultra speed with.
Just after initialization, we are async. Setting the
ultraenb flag while async seems to be harmless, but it
was confusing to see the ULTRAENB flag set in the SCB.
Enhance residual diagnostic to indicate if the residual
if for sense information or normal data transfers.
Indicate the features, bugs, and flags set in the softc
that are used to control firmware patch download when
booting verbose.
In ahc_dump_card_state() fix a logic reversal. The
SCSIPHASE register only exists on U160 controllers.
The SCSISIGI register exists on all controllers. Not
the other way around. Also print out the ERROR register.
Allow ahc_dump_card_state() to be called when the sequencer
is not paused. Add dump card state markers as in the U320
driver.
Implement the SCB_SILENT flag. This is useful for
hushing up the driver during DV or other operations
that we expect to cause transmission errors. The
messages will still print if the SHOW_MASKED_ERRORS
debug option is enabled.
Save and restore the NEGOADDR address when setting
new transfer settings. The sequencer performs lookups
in the negotiation table too and it expects NEGOADDR
to remain consistent across pause/unpause sessions.
Consistently use "offset" instead of "period" to determine
if we are running sync or not.
Add a SHOW_MESSAGES diagnostic for when we assert ATN
during message processing.
Print out IU, QAS, and RTI features when showing transfer options.
Limit the syncrate after all option conformance
changes have taken place in ahd_devlimited_syncrate.
Changes in options may change the final syncrate we
accept.
Keep a copy of the hs_mailbox in our softc so that
we can perform read/modify/write operations on the
hs_mailbox without having to pause the sequencer to
read the last written value. Use the ENINT_COALESS
flag in the hs_mailbox to toggle interrupt coalessing.
Add entrypoints for enabling interrupt coalessing and
setting both a timeout (how long to wait for commands
to be coalessed) and a maximum commands to coaless value.
Add a statistics timer that decides when to enable or
disable interrupt coalessing based on load.
Add a routine, ahd_reset_cmds_pending() which is used
to update the CMDS_PENDING sequencer variable whenever
error recovery compeltes SCBs without notifying the
sequencer. Since ahd_reset_cmds_pending is called
during ahd_unpause() only if we've aborted SCBs, its
call to ahd_flush_qoutfifo should not cause recursion
through ahd_run_qoutfifo(). A panic has been added to
ensure that this recursion does not occur.
In ahd_search_qinfifo, update the CMDS_PENDING sequencer
variable directly. ahd_search_qinififo can be called
in situations where using ahd_reset_cmds_pending() might
cause recursion. Since we can safely determine the
exact number to reduce CMDS_PENDING by in this scenario
without running the qoutfifo, the manual update is sufficient.
Clean up diagnostics.
Add ahd_flush_qoutfifo() which will run the qoutfifo
as well as complete any commands sitting on the
sequencer's COMPLETE_SCB lists or the good status FIFO.
Use this routine in several places that did similar
things in an add-hoc, but incomplete, fashion. A call
to this routine was also added to ahd_abort_scbs() to
close a race.
In ahd_pause_and_flushwork() only return once selections
are safely disabled. Flush all completed commands via
ahd_flush_qoutfifo().
Remove "Now packetized" diagnostic now that this
information is incorperated into the actual negotiation
messages that are displayed.
When forcing renegotiation, don't clober the current
ppr_options. Much of the driver uses this information
to determine if we are currently packetized or not.
Remove some stray spaces at column 1 in ahd_set_tags.
When complaining about getting a host message loop
request with no pending messages, print out the
SCB_CONTROL register down on the card.
Modify the ahd_sent_msg() routine to handle a search
for an outgoing identify message. Use this to detect
a msg reject on an identify message which typically
indicates that the target thought we were packetized.
Force a renegotiation in this case.
In ahd_search_qinfifo(), wait more effectively for SCB
DMA activities to cease. We also disable SCB fetch
operations since we are about to change the qinfifo
and any fetch in progress will likely be invalidated.
In ahd_qinfifo_count(), fix the qinfifo empty case.
In ahd_dump_card_state(), print out CCSCBCTL in the
correct mode.
If we are a narrow controller, don't set the current
width to unknown when forcing a future negotiation.
This just confuses the code into attempting a wide
negotiation on a narrow bus.
Add support for task management function completions.
Modify ahd_handle_devreset so that it can handle
lun resets in addition to target resets. Use
ahd_handle_devreset for lun and target reset task
management functions.
Handle the abort task TMF race case better. We now
wait until any current selections are over and then
set the TMF back to zero. This should cause the sequencer
to ignore the abort TMF completion should it occur.
Correct a bug in the illegal phase handler that
caused us to drop down to narrow when handling the
unexpected command phase case after 3rd party
reset of a packetized device.
Indicate the features, bugs, and flags set in the softc
that are used to control firmware patch download when
booting verbose.
aic79xx.h:
Add coalessing and HS_MAILBOX fields.
Add per-softc variables for the stats "daemon".
Add a debug option for interrupt coalessing activities.
Add two new softc flags:
o AHD_UPDATE_PEND_CMDS
Run ahd_reset_cmds_pending() on the next unpause.
o AHD_RUNNING_QOUTFIFO
Used to catch recursion through ahd_run_qoutfifo().
aic79xx.reg:
Correct register addresses related to the software timer
and the DFDBCTL register.
Add constants paramaterizing the software timer.
Add scratch ram locations for storing interrupt coalessing
tunables.
Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2.
In at least the REV A, these are writable bits. We make
use of that for a swtimer workaround in the sequencer.
Since HS_MAILBOX autoclears, provide a sequencer variable
to store its contents.
Add SEQINT codes for handling task management completions.
aic79xx.seq:
Correct ignore wide residue processing check for
a wide negotiation being in effect. We must be
in the SCSI register window in order to access the
negotiation table.
Use the software timer and a commands completed count to
implement interrupt coalessing. The command complete is
deferred until either the maximum command threshold or a
the expiration of a command deferral timer. If we have
more SCBs to complete to the host (sitting in COMPLETE_SCB
lists), always try to coaless them up to our coalessing limit.
If coalessing is enabled, but we have fewer commands oustanting
than the host's min coalessing limit, complete the command
immediately.
Add code to track the number of commands outstanding.
Commands are outstanding from the time they are placed
into the execution queue until the DMA to post completion
is setup.
Add a workaround for intvec_2 interrupts on the H2A4.
In H2A4, the mode pointer is not saved for intvec2, but
is restored on iret. This can lead to the restoration
of a bogus mode ptr. Manually clear the intmask bits and
do a normal return to compensate. We use intvec_2 to
track interrupt coalessing timeouts.
Since we cannot disable the swtimer's countdown, simply
mask its interrupt once we no longer care about it firing.
In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime
we are notified of an HS_MAILBOX update via the
HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a
local copy of persistant portions of the HS_MAILBOX as
the mailbox auto-clears on any read.
Move the test for the cfg4istat interrupt up an instruction
to hopefully close a race between the next outgoing selection
and our disabling of selections.
Add a missing ret to the last instruction in load_overrun_buf.
Add notifications to the host of task management
completions as well as the completions for commands
that completed successfully before their corresponding
TMF could be sent.
Hold a critical section during select-out processing
until we have a fully identified connection. This
removes a race condition with the legacy abort handler.
Correct a few spelling errors in some comments.
aic79xx_inline.h:
Call ahd_reset_cmds_pending() in ahd_unpause if required.
Update cmdcmplt interrupt statistics in our interrupt
handler.
Allow callers to ahd_send_scb() to set the task management
function.
aic79xx_pci.c:
Disable SERR and pause the controller prior to performing
our mmapped I/O test. The U320 controllers do not support
"auto-access-pause".
aic79xx_osm.c:
Set the task management function now that
ahd_send_scb() doesn't do it for us. We
also perform a lun reset in response to BDR
requests to packetized devices.
Use BUS_SPACE_MAXSIZE_32BIT for the parent dma tags, and
(NSEGS - 1) * PAGE_SIZE for the data buffer tags. FreeBSD/sparc64 is
more strict about checking these values that other arches.
labels are acurate in relation to a fully compiled
sequencer program (all patches downloaded). Correct
a few occurances of a relative jump across a macro
that ended up jumping us into the last instruction
of the macro.
Spproved by: re (bmah)
ahd_pci.c:
Retrieve the allow_memio hint from the resource manager to
determine whether or not to try PCI MEMIO.
aic79xx_osm.h:
aic7xxx_osm.h:
Don't wrongly abuse the callout_reset() interface when trying
to abuse timeouts generated from the CAM layer. This fixes the
console freeze and lost timeout problem that many have reported,
especially on SMP systems.
aic79xx_pci.c
aic7xxx_pci.c
Rewrite the MEMIO test routine to prevent certain broken chipsets
from trying to burst multiple DWORDs to the registers. Also make
the routine better detect byte merging by the host bridge and
deal with it.
aic79xx.reg:
Correct an incorrect register definition.
Approved by: re (rwatson, jhb)
version, plus add support for the new features found in the Rev B
version of the chip. The changelog is quite long and can be provided
on request. Major features include vastly improved protocol violation
handling, full support for the 7902 Rev B, better parity error
handling, and better packetized overrun handling, to name a few.
Approved by: re (blanket)
HP -> CPQ
Rearrange IDs to better match which chips they use.
Convert to uniform product description strings.
Simplify 7901A setup function.
Add the NONPACKFIFO_BUG and PACED_NEGTABLE_BUG entries
for the A.
Add rev B bugs and features.
The double write workaround for CURRSCB is only required if
abort pending is set. Remove this work around and set the
abort pending bug bit on the B at least until we have better
confirmation that the double write is always safe.
Add updated H2B identifiers
Move IOCell paramters into softc and add a hook for the
OSM to modify these as well as other settings prior to
committing them to the chip.
SLEW -> SLEWRATE
PREQDIS in DEVCONFIG1 went away after the A2.
Remove all code that references this bit. This
is especially important since this bit was reused
in the B for a different HW fix workaround.
Properly set the AHD_NEW_IOCELL_OPTS and
AHD_NEW_DFCNTRL_OPTS features for the B.
Remove stray/random extra 7901A generic PCI
table entry. Also switch the correct 7901A
generic entry to use ID_ALL_MASK since we
can only differentiate the 7901A from the
7902 by checking for a "type field" of 0xE.
Set AHD_INTCOLLISIONT_BUG for the Rev B.
Set the PREQDIS bit in DEVCONFIG1 for the B. The
bit is misnamed, but seems to disable a work-around
that breaks on the B on PCI busses.
Add a routine for testing memory mapped register access.
This will hopefully detect things like buggy via chipsets
so that the OSM can fallback to using I/O mapped access
when memory mapped I/O simply will not work.
Approved by: re (blanket)
diagnostic "Setting Mode" messages.
Use a read of HCNTRL to flush our write to CLRCMDCMPLT
on the RevB. This allows us to check to see if the sequencer
is paused and to initiate the interrupt collision workaround
without incuring an extra read.
Approved by: re (blanket)
PCI-X only workarounds are automatically masked out
if we are operating in PCI mode.
Make use of ahd_pci_test_register_access()
Approved by: re (blanket)
Move IOCell paramters into softc and add a hook for the
OSM to modify these as well as other settings prior to
committing them to the chip.
Approved by: re (blanket)
aic7xxx.c:
aic7xxx.h:
aic7xxx.reg:
aic7xxx.seq:
Bring in the protocol violation handler from the U320
driver and replace the NO_IDENT sequencer interrupt code
with the PROTO_VIOLATION code. Support for this code
required the following changes:
SEQ_FLAGS:
IDENTIFY_SEEN -> NOT_IDENTIFIED
Added NO_CDB_SENT
SCB_CONTROL:
TARGET_SCB == STATUS_RCVD for initiator mode
scb->flags:
Added SCB_TARGET_SCB since we cannot rely on
TARGET_SCB as a target/initiator differentiator
due to it being overloaded in initiator mode to
indicate that status has been received.
aic7xxx.seq:
Move data fifo CLRCHN to mesgin_rdptrs which is a safer
location for doing this operation. This also saves a
sequencer instruction.
aic7xxx.c:
aic7xxx.h:
Change ahc/ahd_upate_neg_request() to take a "negotiation
type" enum that allows us to negotiate:
o only if the goal and current parameters differ.
o only if the goal is non-async
o always - even if the negotiation will be for async.
aic7xxx.seq:
Reset the FIFO whenever a short CDB transfer occurs
so that the FIFO contents do not corrupt a future CDB
transfer retry.
Add support for catching the various protocol violations
handled by ahc_handle_protocol_violation.
Reformat some comments.
aic7xxx.c:
aic7xxx.h:
Just for safety, have the aic7xxx driver probe
the stack depth.
aic7xxx.c:
aic7xxx.h:
Save and restore stack contents during diagnostics.
Some chip variants overwrite stale entries on a
stack "pop".
Don't use 0 to probe the stack depth. 0 is the typical
value used to backfill the stack if entries are overwritten
on a "pop".
aic7xxx.h:
Add a missing typedef.
Collapse SCB flag entries so they are bit contiguous.
Add AHD_ULTRA2_XFER_PERIOD for narrow fallback calculations
aic7xxx.c:
Don't panic (as a diagnostic to catch bugs) if we decided to
force the renegotiation of async even if we believe we are
already async. This should allow us to negotiate async instead
of the full user goal rate during startup if bus resets are
disabled.
Add a space to the end of the ahc/ahd_print_devinfo routines
so that it behaves as expected by the code that uses it.
Only force a renegotiation on a selection timeout
if the SCB was valid. Doing otherwise may be dangerous
as the connection was not valid for an unknown reason.
Add additional diagnostic output to ahc_dump_card_state(),
and have it use the register pretty printing functions.
Update ahc_reg_print() to handle a NULL cur_col.
Add a newline to ahc_dump_card_state() output.
Bring back "use_ppr". We need to use_ppr anytime
doppr is true or we have non-zero protocol options.
The later case was not handled in the recent removal
of use_ppr.
Move a comment and remove a useless clearing of use_ppr.
Don't disable ENBUSFREE when single stepping on
a DT capable controller. We cannot re-enable unexpected
busfree detection, so we must clear BUSFREE on each
step instead.
Correct the lookup of the SCB ID in ahc_handle_proto_error.
Remove a diagnostic printf.
Remove unecessary restoration of the STACK for older
chips.
Approved by: re (blanket)
This will hopefully detect things like buggy via chipsets
so that the OSM can fallback to using I/O mapped access
when memory mapped I/O simply will not work.
Approved by: re (blanket)
AHC_ALLOW_MEMIO is set, or the hint hint.ahc.N.allow_memio=1 is
set in the bootloader.
Make use of ah?_pci_test_register_access().
Approved by: re (blanket)
aicasm_gram.y:
Use a direct move from allzeros to emulate a
mvi of 0.
aicasm_insformat.h:
sync $Id$
aicasm_symbol.c:
Minor header change.
Approved by: re (blanket)
alpha. This will take the file out of sync with the private version
that we maintain, but alpha tinderbox has been broken for too long.
Tested on: i386, sparc64, alpha
aic79xx.c:
o Remove redundant ahd_update_modes() call.
o Correct panic in diagnostic should state corruption cause
the SCB Id to be invalid during a selection timeout.
o Add workaround for missing BUSFREEREV feature in Rev A silicon.
o Corect formatting nits.
o Use register pretty printing in more places.
o Save and restore our SCB pointer when updating the waiting queue
list for an "expected" LQ-out busfree.
o In ahd_clear_intstat, deal with the missing autoclear in the
CLRLQO* registers.
o BE fixup in a diagnostic printf.
o Make sure that we are in the proper mode before disabling
selections in ahd_update_pending_scbs.
o Add more diagnostics.
o task_attribute_nonpkt_tag -> task_attribute: we don't need a
nonpkt_tag field anymore for allowing all 512 SCBs to be
used in non-packetized connections.
o Negotiate HOLD_MCS to U320 devices.
o Add a few additional mode assertions.
o Restore the chip mode after clearing out the qinfifo so that
code using ahd_abort_scbs sees a consistent mode.
o Simplify the DMA engine shutdown routine prior to performing
a bus reset.
o Perform the sequencer restart after a chip reset prior to
setting up our timer to poll for the reset to be complete.
On some OSes, the timer could actually pre-empt us and order
is important here.
o Have our "reset poller" set the expected mode since there is
no guarantee of what mode will be in force when we are called
from the OS timer.
o Save and restore the SCB pointer in ahd_dump_card_state(). This
routine must not modify card state.
o Ditto for ahd_dump_scbs().
aic79xx.h:
o Add a few more chip bug definitions.
o Align our tag on a 32bit boundary.
aic79xx.reg:
aic79xx.seq:
o Start work on removing workarounds for Rev B.
o Use a special location in scratch from for stroring
our SCBPTR during legacy FIFO allocations. This corrects
problems in mixed packetized/non-packetized configurations
where calling into a FIFO task corrupted our SCBPTR.
o Don't rely on DMA priority to guarantee that all data in
our FIFOs will flush prior to a command completion notification
going out of the command channel. We've never seen this assumption
fail, but better safe than sorry.
o Deal with missing BUSFREEREV feature in H2A.
o Simplify disconnect list code now that the list will always
have only a single entry.
o Implement the AHD_REG_SLOW_SETTLE_BUG workaround.
o Swith to using "REG_ISR" for local mode scratch during
our ISR.
o Add a missing jmp to the data_group_dma_loop after our
data pointers have been re-initialized by the kernel.
o Correct test in the bitbucket code so that we actually
wait for the bitbucket to complete before signaling the
kernel of the overrun condition.
o Reposition pkt_saveptrs to avoid a jmp instruction.
o Update a comment to reflect that the code now waits for
a FIFO to drain prior to issuing a CLRCHN.
aic79xx_inline.h:
o Remove unused untagged queue handling code.
o Don't attempt to htole64 what could be a 32bit value.
aic79xx_pci.c:
o Set additional bug flags for rev A chips.
This ensures that we don't enter our interrupt handler until
all OSM components it might reference have been fully initialized
during attach.
Remove vestiges of untagged queue handling.
Add hints to ahd_get_scb() so it knows what type of SCB collision
management to perform for each new transaction.
Properly disable/enable IU_REQ with changes in tagged queuing and
disconnection settings passed in by CAM.
Uninline some routines that are just too big to be inlined.
Add some helper macros for SCB ID collision management.
Use a hardware SCB rather than a full SCB for the "next
SCB to queue" sentinal.
Update for new "high SCBID bit" qoutfifo delivery scheme.
If interrupts are disabled on the card, don't bother running
our interrupt handler. Our handler was called due to a shared
interrupt, and the card's interrupts are explicitly disabled
to prevent entry into our interrupt handler.
functions for register pretty-printing.
Implement "top bit of SCBID is valid bit" qoutfifo delivery scheme.
"the the" -> "the".
Remove old and never used tag collision chain handling in the
sequencer. Tag collisions are never allowed to get as far as
on the controller.
Simplify busy target table handling routines.
Update comments to reflect reality.
Add support for catching more protocol violations.
Correct a bug in data fifo handling in mixed packetized and
non-packetized environments. SG_STATE must be cleared even
if an SG fetch is not in progress at the time of FIFO shutdown
or we may confuse the non-packetized transaction idle-loop.
busy target table addressing changes, our qoufifo scheme,
and long lun support.
Drop bus reset hold delay to 25us.
Remove chip workarounds for revisions that never went to
production.
Add aic7901A identification information.
Remove untagged queue logic.
Push protocol violation handler to its own routine. We now
properly detect and recovery from the following target induced
protocol violations:
o Unexpected or invalid non-packetized Relesection
o Command complete with no status message
o Good Status after incomplete cdb transfer
Add an SCB collision avoidance algorithm that allows us to
use all 512 SCBs for non-packetized operations. There is
still the possibility of running out of SCBs with non-colliding
tag identifiers, but the algorithm ensures that the stall will
be rare and short lived.
Convert to a read-only algorithm for validing entries in the
qoufifo. The sequencer now toggles the high bit of the SCB
identifier on each wrap around of the qinfifo. If the high
bit doesn't match the expected value for this pass of the
qoufifo, the entry is not valid. This has the benefit of
working on machines that have large granularity cache write
back semantics without requiring any additional memory.
Remove lots of code related to untagged SCB queues. Since
these controllers can keep a fully busy target table, we
will never have untagged SCB queues.
Lots of improvements to diagnostic logging.
Clarify some comments.
Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO
handler. Just clearing the interrupt status is sufficient and
this avoids the chance of disabling busfree detection in connection
that occurs while we are handling the busfree interrupt.
Clear all possible interrupt sources when handling a busfree
interrupt. The hardware clears some but not all of them.
Don't panic if we get into the default SCSIINT handler.
Dump the card state and clear all interrupt sources in the
hope that we can continue.
LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing
against values in the PERRDIAG register.
According to SPI4, the bus free that is required after certain
PPR negotiations will only occur at the end of all message phases.
Handle the bus free if it occurs after a transaction in either
the message-in or message-out phases. The busfree can also occur
if the status of IU_REQ changes due to a WDTR or SDTR message.
We now set the expect busfree flag in ahd_set_syncrate so that
it works regardless of message type.
Correct a problem with missing certain busfree events. The
chip supports single-stepping even if a SCSIINT is pending.
This obviates the need to clear all of the SCSI interrupt enables
prior to single stepping. Since ENBUSFREE can only be disabled
manually and not re-enabled, avoiding touching this bit in the
single-step case yields reliable bus free detection.
Enhance ahd_clear_intstat to clear all SCSIINT sources.
Only use ahd_update_pending_scbs() if we are active on the
bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the
execution queue if a selection might be in process since
the sequencer uses this bit to detect PPR negotiation to
a target with an outstanding IU_REQ agreement.
Allocate the SCB delivery mechansim's sentinal SCB specially
so we don't waste a valid SCB for this task.
Move tranceive state settle logic to ahd_chip_init() since
this needs to occur after every chip reset, not just the
chip reset that happens during primary driver initialization.
Correct a bug with transmitting lun information in packetized
connections.
Restrict busy target table operations to the range of luns
that can be used for non-packetized connections. Larger luns
can only be accessed in packetized mode.
Correct a busy target table addressing bug.
Be more careful about how we shutdown the DMA engines during
bus reset events.
Only freeze the SIMQ once regardless of the number of bus
reset events that occur while we are polling for the resets
to stop.
Don't rely on the sequencer remaining paused() during our
reset poll. It is safe for the sequencer to run during this
time, and many callers to the bus reset code would need to
be modified to make this assumption universally true.
Even if we are not going to clobber SCB state when an auto-request
sense SCB has a check condition, we must still unfreeze the queue.
Re-arrange the BAD STATUS handler to handle this case appropriately.
Modify the SCB download size depending on whether long luns are
being stored in the SCB.
Add ahd_print_register() for pretty printing register diagnostics.
Don't trust that the flexport logic to detect the presence of
a seeprom is available. It may not be on some motherboard
implementations.
"the the" -> "the"
