The QCA955x looks a lot like the AR724x PCIe controller, except it
supports two root complexes. Unfortunately I only have one, so
although this code has started down the path of supporting more than
one, it's definitely not yet ready.
Tested:
* AP135 board (QCA9558 SoC), with the 11ac NIC swapped for an AR9380
PCIe NIC.
Notes:
* Yes, this driver isn't very pretty. I decided to commit what I have
versus holding onto something that isn't yet finished. It is enough
to bring up the above NIC and interrupt routing works, so it's a good
start.
* However, yes, the DDR flush routine hooks need to be fixed up.
I don't think I'm firing the right one at the moment.
A lot of these embedded boards don't have a unique MAC address per
device stored somewhere unique - sometimes they'll have one MAC
for both arge NICs; someties they'll have one MAC for both arge NICs
/and/ the ath NICs. In these instances, we need to derive device
specific MAC addresses from the base MAC address.
These functions will be used by some follow-up code that'll slot
into if_arge and if_ath.
The QCA955x has more mux interrupts going on - and the AR934x actually does,
but I cheated and assigned wlan and pcie to the same interrupt line.
They are, there's just a status register mux that I should've been using.
Luckily this isn't too bad a change in itself - almost all of the
Atheros MIPS configurations use a _BASE file to inherit from.
Except PB92, which I should really fix up at some point.
The AR934x will use the legacy apb for now until I write its replacement.
The QCA955x SoC I'm doing bring-up on will have a separate qca955x_apb.c
implementation that includes hooking into IP2/IP3 and doing further
interrupt demuxing as appropriate.
This adds the initial frequency poking and configures up enough
for it to boot and spit out data over the console.
There's still a whole bunch of work to do in the reset path
and devices to support this thing, but hey, it's alive!
ath> go 0x80050100
## Starting application at 0x80050100 ...
CPU platform: Atheros AR9558 rev 0
CPU Frequency=720 MHz
CPU DDR Frequency=600 MHz
CPU AHB Frequency=200 MHz
platform frequency: 720 MHz
CPU reference clock: 0 MHz
CPU MDIO clock: 40 MHz
Done at: hackathon
Obtained from: Linux OpenWRT, Qualcomm Atheros
This code reads the PLL configuration registers and correctly programs
things so the UART and such can come up.
There's MIPS74k platform issues that need fixing; but this at least brings
things up enough to echo stuff out the serial port and allow for interactive
debugging with ddb.
Tested:
* AR71xx SoCs
* AR933x SoC
* AR9344 board (DB120)
Obtained from: Qualcomm Atheros; Linux/OpenWRT
ar724x_pci.c.
* Move out the code which populates the firmware into ar71xx_fixup.c
* Shuffle around the ar724x fixup code to match what the ar71xx fixup
code does.
I've validated this on an AR7240 with AR9285 on-board NIC. It doesn't
yet load, as the AR9285 EEPROM code needs to be made "flash aware."
TODO:
* Validate that I haven't broken AR71xx
* Test AR9285/AR9287 onboard NICs, complete with EEPROM code changes
* Port over the needed BAR hacks for AR7240, AR7241 and AR7242 from
Linux OpenWRT. The current WAR has only been tested on the AR7240
and I'm not sure the way the BAR register is treated is "right".
The "fixup" method here is right when setting the BAR for local access -
ie, the BAR address is either 0xffff (AR7240) or 0x1000ffff (AR7241/AR7242),
but the ath9k-fixup.c code (Linux OpenWRT) does this when setting the
initial "fixup" BAR. It then restores the original BAR.
I'll have to read the ar724x PCI bus glue to see what other special cases
await.
- Replace MIPS24K-specific code with more generic framework that will
make adding new CPU support easier
- Add MIPS24K support for new framework
- Limit backtrace depth to 1 for stability reasons and add option
HWPMC_MIPS_BACKTRACE to override this limitation
This is reported to work on the AR7240 based Ubiquiti Rocket M5
but I haven't tested it on that hardware. I also don't yet have
it fully working on the AR7242 based development board here;
probe/attach functions but the register space resource looks like
the endian-ness is wrong (0x10000000 instead of 0x00001000).o
Further digging will be required.
Submitted by: Luiz Otavio O Souza
This is untested but should at least allow an AR724X to boot.
The current code is lacking the detail needed to expose the PCIe bus.
It is also lacking any NIC, PLL or flush/WB code.
This works well enough to bring a system up to single-user mode
using an MDROOT.
Known Issues:
* The EHCI USB doesn't currently work and will panic the kernel during
attach.
* The onboard ethernet won't work until the PLL routines have been
fleshed out and shoe-horned into if_arge.
* The WMAC device glue (and quite likely the if_ath support)
hasn't yet been implemented.
* Implement a SoC probe function, from Linux, which determines the
SoC family, type and revision. This only probes the AR71xx series
SoC and (currently) panics on others.
* Migrate some of the AR71XX specific hardware init (USB device, determining
system frequencies) into using the cpuops introduced in an earlier commit.
Other SoC specific hardware stuff (per-device flush/WB, GPIO pin wiring,
Ethernet PLL setup, other things I've likely missed) will be introduced in
subsequent commits.
Reviewed by: imp@
Obtained from: (partially) Linux
1) Adds future RMI directories
2) Places intr_machdep.c in specfic files.arch pointing to the generic
intr_machdep.c. This allows us to have an architecture dependant intr_machdep.c
(which we will need for RMI) in the machine specific directory
3) removes intr_machdep.c from files.mips
4) Adds some TARGET_XLR_XLS ifdef's for the machine specific intra_machdep.h. We
may need to look at finding a better place to put this. But first I want to
get this thing compiling.
registers with ar71xx_bus_space_reversed. Note, that byte order
of values is handled by drivers. bus_spaces fixes only position
of register in word.
- Replace .hints hack for AR71XX UART with ar71xx_bus_space_reversed.
