the NFS subsystems use five of the rpcsec_gss/kgssapi entry points,
but since it was not obvious which others might be useful, all
nineteen were included. Basically the nineteen entry points are
set in a structure called rpc_gss_entries and inline functions
defined in sys/rpc/rpcsec_gss.h check for the entry points being
non-NULL and then call them. A default value is returned otherwise.
Requested by rwatson.
Reviewed by: jhb
MFC after: 2 weeks
cloned from the old NFS client, plus additions for NFSv4. A
review of this code is in progress, however it was felt by the
reviewer that it could go in now, before code slush. Any changes
required by the review can be committed as bug fixes later.
This is in no way a complete DFS/radar detection implementation!
It merely creates an abstracted interface which allows for future
development of the DFS radar detection code.
Note: Net80211 already handles the bulk of the DFS machinery,
all we need to do here is figure out that a radar event has occured
and inform it as such. It then drives the DFS state engine for us.
The "null" DFS radar detection module is included by default;
it doesn't require a device line.
This commit:
* Adds a simple abstracted layer for radar detection state -
sys/dev/ath/ath_dfs/;
* Implements a null DFS module which doesn't do anything;
(ie, implements the exact behaviour at the moment);
* Adds hooks to the ath driver to process received radar events
and gives the DFS module a chance to determine whether
a radar has been detected.
Obtained from: Atheros
filters working. (All other filters - switch without L2 info rewrite,
steer, and drop - were already fully-functional).
Some contrived examples of "switch" filters with L2 rewriting:
# cxgbetool t4nex0 iport 0 dport 80 action switch vlan +9 eport 3
Intercept all packets received on physical port 0 with TCP port 80 as
destination, insert a vlan tag with VID 9, and send them out of port 3.
# cxgbetool t4nex0 sip 192.168.1.1/32 ivlan 5 action switch \
vlan =9 smac aa:bb:cc:dd:ee:ff eport 0
Intercept all packets (received on any port) with source IP address
192.168.1.1 and VLAN id 5, rewrite the VLAN id to 9, rewrite source mac
to aa:bb:cc:dd:ee:ff, and send it out of port 0.
MFC after: 1 week
Some files keep the SUN4V tags as a code reference, for the future,
if any rewamped sun4v support wants to be added again.
Reviewed by: marius
Tested by: sbruno
Approved by: re
Reference code that shows how to get a packet's timestamp out of
cxgbe(4). Disabled by default because we don't have a standard way
today to pass this information up the stack.
The timestamp is 60 bits wide and each increment represents 1 tick of
the T4's core clock. As an example, the timestamp granularity is ~4.4ns
for this card:
# sysctl dev.t4nex.0.core_clock
dev.t4nex.0.core_clock: 228125
MFC after: 1 week
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
- 77115: Implement support for O_DIRECT.
- 98425: Fix a performance issue introduced in 70131 that was causing
reads before writes even when writing full blocks.
- 98658: Rename the BALLOC flags from B_* to BA_* to avoid confusion with
the struct buf B_ flags.
- 100344: Merge the BA_ and IO_ flags so so that they may both be used in
the same flags word. This merger is possible by assigning the IO_ flags
to the low sixteen bits and the BA_ flags the high sixteen bits.
- 105422: Fix a file-rewrite performance case.
- 129545: Implement IO_INVAL in VOP_WRITE() by marking the buffer as
"no cache".
- Readd the DOINGASYNC() macro and use it to control asynchronous writes.
Change i-node updates to honor DOINGASYNC() instead of always being
synchronous.
- Use a PRIV_VFS_RETAINSUGID check instead of checking cr_uid against 0
directly when deciding whether or not to clear suid and sgid bits.
Submitted by: Pedro F. Giffuni giffunip at yahoo
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
set the f_flags field of "struct statfs". This had the interesting
effect of making the NFSv4 mounts "disappear" after r221014,
since NFSMNT_NFSV4 and MNT_IGNORE became the same bit.
Move the files used for a diskless NFS root from sys/nfsclient
to sys/nfs in preparation for them to be used by both NFS
clients. Also, move the declaration of the three global data
structures from sys/nfsclient/nfs_vfsops.c to sys/nfs/nfs_diskless.c
so that they are defined when either client uses them.
Reviewed by: jhb
MFC after: 2 weeks
create reasonably large cache for the keys that is filled when
needed. The previous version was problematic for very large providers
(hundreds of terabytes or serval petabytes). Every terabyte of data
needs around 256kB for keys. Make the default cache limit big enough
to fit all the keys needed for 4TB providers, which will eat at most
1MB of memory.
MFC after: 2 weeks
In particular:
- implement compat shims for old stat(2) variants and ogetdirentries(2);
- implement delivery of signals with ancient stack frame layout and
corresponding sigreturn(2);
- implement old getpagesize(2);
- provide a user-mode trampoline and LDT call gate for lcall $7,$0;
- port a.out image activator and connect it to the build as a module
on amd64.
The changes are hidden under COMPAT_43.
MFC after: 1 month
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
Add new RAID GEOM class, that is going to replace ataraid(4) in supporting
various BIOS-based software RAIDs. Unlike ataraid(4) this implementation
does not depend on legacy ata(4) subsystem and can be used with any disk
drivers, including new CAM-based ones (ahci(4), siis(4), mvs(4), ata(4)
with `options ATA_CAM`). To make code more readable and extensible, this
implementation follows modular design, including core part and two sets
of modules, implementing support for different metadata formats and RAID
levels.
Support for such popular metadata formats is now implemented:
Intel, JMicron, NVIDIA, Promise (also used by AMD/ATI) and SiliconImage.
Such RAID levels are now supported:
RAID0, RAID1, RAID1E, RAID10, SINGLE, CONCAT.
For any all of these RAID levels and metadata formats this class supports
full cycle of volume operations: reading, writing, creation, deletion,
disk removal and insertion, rebuilding, dirty shutdown detection
and resynchronization, bad sector recovery, faulty disks tracking,
hot-spare disks. For Intel and Promise formats there is support multiple
volumes per disk set.
Look graid(8) manual page for additional details.
Co-authored by: imp
Sponsored by: Cisco Systems, Inc. and iXsystems, Inc.
