NFSCL, NFSD instead of NFSCLIENT, NFSSERVER since
NFSCL and NFSD are now the defaults. The client change is
needed for diskless configurations, so that the root
mount works for fstype nfs.
Reported by seanbru at yahoo-inc.com for i386/XEN.
Approved by: re (hrs)
the 'debugging' section of any HEAD kernel and enable for the mainstream
ones, excluding the embedded architectures.
It may, of course, enabled on a case-by-case basis.
Sponsored by: Sandvine Incorporated
Requested by: emaste
Discussed with: kib
- Move USB serial drivers earlier to match their placement in other kernel
configs.
- Add descriptions to various USB drivers.
- Move the USB wireless drivers into a new section.
- Add ulscom to the list of USB serial drivers.
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
machine arm
device mem
options GEOM_BSD
options GEOM_MBR
Remove the first two from all kernel configuration files and
change geom_bsd and geom_mbr from standard to optional.
o It has been tested only on KB9202, KB9202A and KB9202B boards
o Better comments about hints
o option<space><tab>
o Add newer SX_NOINLINE option.
o Fix a few comments
As clearly mentioned on the mailing lists, there is a list of drivers
that have not been ported to the MPSAFE TTY layer yet. Remove them from
the kernel configuration files. This means people can now still use
these drivers if they explicitly put them in their kernel configuration
file, which is good.
People should keep in mind that after August 10, these drivers will not
work anymore. Even though owners of the hardware are capable of getting
these drivers working again, I will see if I can at least get them to a
compilable state (if time permits).
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
to detect (or load) kernel NLM support in rpc.lockd. Remove the '-k'
option to rpc.lockd and make kernel NLM the default. A user can still
force the use of the old user NLM by building a kernel without NFSLOCKD
and/or removing the nfslockd.ko module.
only USB 1.1 speeds available, but this shouldn't hurt. Now that we have
working usb support for this board, this is a natural followup.
Approved by: re (kensmith)
FreeBSD/arm installworld install is only 170MB. The smallest SD card
I could find at the store today was 512MB (and it was only $10 after
rebate), with a 2GB card for as low as $25.00...
Now that the IIC stuff has been sorted out, include that as well.
Include hints for the icee 16kb 16-bit i2c device. It should include
info about the temperature sensor as well, but that driver isn't quite
ready.
Add bpf for dhclient happiness.
MFC After: 1 week
The 'nooption' kernel config entry has to be used to turn KSE off now.
This isn't my preferred way of dealing with this, but I'll defer to
scottl's experience with the io/mem kernel option change and the grief
experienced over that.
Submitted by: scottl@
an explicit comment that it's needed for the linuxolator. This is not the
case anymore. For all other architectures there was only a "KEEP THIS".
I'm (and other people too) running a COMPAT_43-less kernel since it's not
necessary anymore for the linuxolator. Roman is running such a kernel for a
for longer time. No problems so far. And I doubt other (newer than ia32
or alpha) architectures really depend on it.
This may result in a small performance increase for some workloads.
If the removal of COMPAT_43 results in a not working program, please
recompile it and all dependencies and try again before reporting a
problem.
The only place where COMPAT_43 is needed (as in: does not compile without
it) is in the (outdated/not usable since too old) svr4 code.
Note: this does not remove the COMPAT_43TTY option.
Nagging by: rdivacky
is a ARM920T based CPU with a bunch of built-in peripherals. The
inital import supports the SPI bus, the TWI bus (although iicbus
integration is not complete), the uarts, the system timer and the
onboard ethernet. Support for the Kwikbyte KB9202
(http://www.kwikbyte.com) board is also included, although there's no
reason why the 9200 and the 9201 wouldn't also work. Primitive
support for running under the skyeye emulator is also provided
(although skyeye's support for the AT91RM9200 is a little weak).
The code has been structured so that other members of Atmel's arm family can
be supported in the future. The AT91SAM9260 is not presently supported
due to lack of hardware. The arm7tdmi families are also not supported
becasue they lack an MMU.
Many thanks to cognet@ for his help and assistance in bringing up this
board. He did much of the vm work and wrote parts of the uart and
system timer code as well as the bus space implementation.
The system boots to single user w/o problem, although the serial
console is a little slow and the ethernet driver is still in flux.
This work was sponsored by Timing Solutions, Corporation. I am
grateful to their support of the FreeBSD project in this manner.
