of queue entries have to be at least 16 bits now! If we're running
a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix
typo in checking against 2200 F/W revision. Slightly fix/reorder fabric
login stuff. Change to usage of isp_getrqentry for code clarity. Add some
defensive dual bus assumptions. Various cleanups, etc...
Role the core version minor number. Change the arguments to the dma
setup function to use a u_int16_t for the output request loop pointer
(truly amazing that this hasn't blown up in anyones face so far). Do
some shuffling around of some items.
by Qlogic. The firmware is now also kept from compiling by default
unless some config options are set.
While we're at it, roll the 2200 f/w to 2.01.0. Still need to get the
1.17.26 2100 f/w working as it solves a lot of problems but it doesn't
want to work yet with this driver (:-)).
out of the PCI CLASS reg and store it in the softc. Use the getenv_quad
function to get a WWN override from the environment. Look for a config
value for same. Make slightly less lame the wwn seed construction.
is documented to be 0x18 in the Adaptec manual, however there appears to
be a newer board rev with code 0x19. I added a #define for this and
updated the probe code so that this board will be properly identified
in the probe messages. (Currently it's just identified generically as
an AIC-6915 chip.)
o Delete pcic1 from NEWCARD
o Add explicit resource hints to pcic0
o Get attach working with newbus, kinda (it does all the newbus stuff,
but doesn't try to attach the pccard yet, too many panics).
o Disable ie0 and le0 in NEWCARD config. There appears to be a bug in
the isa_compat code wrt memory conflicts with newbus drivers for
reasons unknown.
o Minor cleanups.
ES1371 and ES1373 PCI Audio Sound Chips.
The 1371 and 1373 can be found on newer CreativeLabs/Ensoniq
sound cards such as the SoundBlaster PCI 16,64 and 128.
Submitted by: Russell Cattelan <cattelan@thebarn.com>
Obtained from: Parts obtained from linux, but rewritten by Russell
Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c)
Make sio work for pccard here - pccardd doesn't activate interrupts
until after prove has succeeded.
Mark the initial reset of likely sio ports as broken as it depended on
config supplying a list of locations to probe, devices are now proved
standalone.
Optimize a bit of COM_NOAST4() logic.
Use bus_get_resource_start() etc rather than using isa-centric calls.
Reactivate the IIR_TXRDYBUG test, I've got a card here with it.
Try to be a bit smarter about activating interrupts (ie: don't panic
if polled)
Fix some style bugs that have crept in over time (there are still more).
Don't use NFDC as an arbitary limit, it is not required and goes against
using PnP fdc devices (eg: when PNPBIOS is turned on, the motherboard
devices (sio, fdc, etc etc) are detected via PnP, not config(8).)
o Rewrite probe code to work in the newbus world.
o Add preliminary pnp support. I have no clue what the pnp ids for
the older ISA machines/cards. I don't have any of these cards/machines
so I'll have to rely on the user community to give me help.
o Minor code reformatting.
Attach hasn't been touched, and there may be some config issues that
we need to deal with as well. These will follow in time.
Cleaning up the code:
- Declare many functions static
- Change variable names to make them more self explanatory
- Change usbd_request_handle -> usbd_xfer_handle
- Syntactical changes
- Remove some unused code
- Other KNF changes
Interrupt context handling
- Change delay to usbd_delay_ms were possible (takes polling mode into
account)
- Change detection mechanism for interrupt context
Add support for pre-allocation DMA-able memory by device driver
Add preliminary support for isochronous to the UHCI driver (not for OHCI
yet).
usb.c, uhci.c, ohci.c
- Initial attempt at detachable USB host controllers
- Handle the use_polling flag with a lttle more care and only set it if
we are cold booting.
usb.c, uhci.c ohci.c, usbdi.c usbdi_util.c usb_subr.c
- Make sure an aborted pipe is marked as not running.
- Start queued request in the right order.
- Insert some more DIAGNOSTIC sanity checks.
- Remove (almost) unused definitions USBD_XFER_OUT and USBD_XFER_IN.
usb.c, usb_subr.c
- Add an event mechanism so that a userland process can watch devices
come and go.
ohci.c
- Handle the case when a USB transfer is so long that it crosses two
page (4K) boundaries. OHCI cannot do that with a single TD so we make
a chain.
ulpt.c
- Use a bigger buffer when transferring data.
- Pre-allocate the DMA buffer. This makes the driver slightly more
efficient.
- Comment out the GET_DEVICE_ID code, because for some unknown reason it
causes printing to fail sometimes.
usb.h
- Add a macro to extract the isoc type.
- Add a macro to check whether the routine has been entered after splusb
and if not, complain.
usbdi.c
- Fix a glitch in dequeueing and aborting requests on interrupt pipes.
- Add a flag in the request to determine if the data copying is done by
the driver or the usbdi layer.
Without this, ioctl commands for setting formats and speeds were
essentially ignored for simplex devices until the application actually
performed a read or write.
* Make sure that both channels are set in the SB mixer code and provide a
mixer table specifically for the ess18xx which supports the extended
accuracy available on this part.
* Fix a stupid bug in ess_format() which ignored the passed-in format and
changed the hardware based on the value which was set last time. This
meant that the hardware setting was often not set correctly at all.
* Add a custom identify driver for the ESS1888 which automagically detects
and adds the device in a pseudo-PnP way. This driver also emits the magic
sequence which enables the sound hardware after a hard reset, allowing
it to work correctly for the sound hardware of a PWS 433au (and probably
all other PWS class alpha machines).
With these changes, I was able to play back simple sounds on my 433au. I
have not tested recording or any other formats other than 8bit ulaw and
16bit stereo.
Make tuner on French SECAM Hauppauge cards work
Submitted by: Cyrille Lefevre <clefevre@citeweb.net>
Fix clipping bugs ready for Xv support in XFree86 4.0
Submitted by: Thomas Mueller <tmueller@thmu.de>
Fix the 'feature' where /dev/vbi needed to be opened before /dev/bktr
when using Teletext with Alevt and FXTV.
Requested by: Randall Hopper
Rename a few (I wish companies would stop buying each other)
Add a quirk entry for hubs that say they are self powered but are
in fact bus powered (usage in uhub follows shortly).
condition for Short transfers.
Change the scheduling to Depth first. We now transfer as many TD's as
possible from QH before moving to the next queue (Breadth first). It should
still be verified that this does not lead to starvation in a busy system
(in the case were transfers are added to the beginning of the control
or bulk queues).
